N150 IVO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
– Manual format alignment – Through hollow shaft max. ø14 mm – Resolution: 1440 steps/revolution ±4096 revolutions – Display: LCD backlit, two lines – Absolute multiturn measuring system – Actual value and target display – Interface RS485 Technical data - electrical ratings Voltage supply 24 VDC ±10 % Current consumption ≤30 mA Display LCD, 7-segment display, 2-lines, backlit Measuring principle Absolute multiturn measuring system Steps per turn 1440 Number of turns 4096 / 12 bit Spindle pitch ≤14 mm Interface RS485 (ASCII protocol) Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Spindle pitch Counting direction Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Standard DIN EN 61010-1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL approval / E63076 N 150 Technical data - mechanical design Shaft type ø14 mm (through hollow shaft) Operating speed ≤600 rpm (short-term) Protection DIN EN 60529 IP 65 Operating temperature -10...+50 °C Storage temperature -20...+70 °C Relative humidity 80 % non-condensing Torque support Torque pin provided at housing Connection - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin Housing type Surface-mount with hollow shaft Dimensions 37 x 75 x 45 mm Mounting Surface-mount with hollow shaft Weight approx. 120 g Material Polyamide black, UL 94V-0 Through hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485
www.baumer.com/motion Subject to modification in technic and design. Errors and omissions excepted.14/5/2014 N 150 Part number N 150. 1 3 A 01 Through hollow shaft A ø14 mm Display A Inclined B Horizontal at front Voltage supply 3 24 VDC Connection
0 Connector output M8
1 Cable output M8
1 RS485
Through hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 Accessories Connectors and cables Z 178.A01 Adaptor cable between cable connector M8 and female M16, 1 m Z 178.AW1 Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Z 178.B01 Female connector M8, 4-pin, less cable Z 178.D05 Data and supply cable M8, Master to N 150 and N 155, 5 m Z 178.S01 Cable connector M8, 4-pin, less cable Z 178.V01 Coupling cable with M8 - M8, 1 m cable Z 178.V03 Coupling cable with M8 - M8, 3 m cable Z 178.V05 Coupling cable with M8 - M8, 5 m cable Z 178.V10 Coupling cable with M8 - M8, 10 m cable Z 178.050 Data and supply cable, ø5 mm, 4 cores, shielded, on 50 m drum N 150 spindle position display supports the editing engineer in manual spindle positioning. The principal benefits of the new electronic spindle position display are saving time in machine setup and editing as well as eliminating errors when aligning formats to new position values. The absolute measuring system captures any change in position even in powerless state. The backlit LCD display provides the editing engineer with all necessary information for efficient editing of new spindle positions. The two-line display shows both current value and target. A little arrow signalizes the editing engineer the direction the spindle must be turned to get to the new position. RS485 serial interface enables network of maximum 32 spindle position displays to PC or PLC. For complete solutions also memory controllers serving as decentralized operating and memory terminals are avail- able. Up to 100 format profiles can be stored by teach-in. Upon request the desired profile is recalled upon press- ing a button and and retransmitted to every spindle position display and shown as target.
Description
www.baumer.com/motion Spindle position displays Subject to modification in technic and design. Errors and omissions excepted.14/5/2014 N 150 Through hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 Connector Assignment Pin 1 Tx/Rx-, RS485 Pin 2 Tx/Rx+, RS485 Pin 3 Sensor supply +24 V Pin 4 Sensor supply 0 V 4 3 M8 connector M8 female connector Terminal assignment Dimensions A ø12ø12 A 300 150 female connector connector Cable outputConnect or output 20.5 2216 6.5 30.15 31.8 12.5 ø14H7 ø20 75° 4.8 ø6h9 0.5x 45° 2:1 Pin M4 Connector Female connector Optional display position Torque pin Seal
www.baumer.com/motion Subject to modification in technic and design. Errors and omissions excepted.14/5/2014 N 150 Through hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485