N142 IVO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Motive spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft ø20 mm / ø25 mm – Interface RS485 – Resolution: 2304 steps/revolution ±4096 revolutions – Two operating keys for format alignment touch by – touch Technical data - electrical ratings Voltage supply 24 VDC ±10 % Current consumption ≤40 mA Display LCD, 7-segment display, 2-lines, backlit Measuring principle Absolute multiturn measuring system Measuring range -999,99...+9999,99 mm Steps per turn 2304 Number of turns 4096 / 12 bit Spindle pitch ≤23 mm Interface RS485 (ASCII protocol) Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Motive positioning Two softkeys for format alignment Direct motor connection to N 142 by motor cable Standard DIN EN 61010-1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL/cUL N 142 Technical data - mechanical design Hollow shaft ø20 mm, ø25 mm Operating speed ≤600 rpm (short-term) Protection DIN EN 60529 IP 65 Operating temperature -10...+50 °C Storing temperature -20...+70 °C Relative humidity 80 % non-condensing Torque support Torque pin provided at housing E-connection - Cable output (30 cm) with male/female connector M16, 5-pin - Motor cable with female connector M16, 12-pin Operation / keypad Membrane with two keys Housing type Surface-mount with hollow shaft Dimensions W x H x L 56 x 100 x 62.5 mm Mounting Surface-mount with hollow shaft Weight approx. 200 g Material Polycarbonate black, UL 94V-0 Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 2 Subject to modification in technic and design. Errors and omissions excepted.30/10/2008 N 142 Part number N 142. 1 3 A 01 Hollow shaft A Hollow shaft ø25 mm B Hollow shaft ø20 mm Display A Inclined Voltage supply 3 24 VDC E-connection 1 Cable output M16, motor cable 0.5 m 2 Cable output M16, motor cable 1.5 m Interface
1 RS485
Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 Accessories Connectors and cables (page %S) Z 165.A01 Adaptor cable between cable connector M16 and female M8, 1 m Z 165.AW1 Cable connector M16, 5-pin, less cable with integrated terminating resistor 120 Ω Z 165.B01 Mating connector M16, 5-pin, less cable Z 165.D05 Data and supply cable M16, Master to N 140, N 141 and N 142, 5 m Z 165.S01 Cable connector M16, 5-pin, less cable Z 165.V01 Coupling cable between M16 and M16, 1 m multiconDrive represents a simplified and very efficient, reasonably priced system for automatic format alignment. With multiconDrive the spindle position displays communi- cate directly with EC motors. Every spindle position display is connected to the corresponding motor by a separate cable output providing the motor without delay with the signals “clockwise”, “counterclockwise”, “rotation speed” for switchover to high/low speed. The spindle position display provides two keys for clock- wise and counterclockwise direction used during the first editing operation. The key makes the motor moving into the requested direction. A soft touch results in a defined STEP. Thus, new spindle positions can be edited under direct visual check of the operator with an accuracy of ±1/100 mm. Shaft position parameters once set can be filed as profile in the control. The serial interface enables network of maxi- mum 32 spindle position displays with PC or PLC. For complete solutions N 242 memory controller as operat- ing and memory terminal is available. Up to 100 format profiles can be stored by teach-in. The respective position parameters can be retransmitted at any time as target to the respecitve spindle position displays to release automatic format alignment cycles.
Description
www.baumerivo.com Spindle Position Displays N 142 Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 24 V 0 V IN 1 output IN 1 input IN 2 output IN 2 input (logic 24 V) OUT 1 IN 1 (left) IN 2 (right) IN 4 (speed) 24 V n.c. n.c. AI- (0...10 V) AI+ (0...10 V) OUT 3 (fault) IN 3 (speed) 0 V A B C D E F G H J K L M supply voltage Error SPAMotor Motor left Motor right Speed n.c. key 1 external key 2 external n.c. n.c. Error signal Speed GND release counter- clockwise Enable n.c. release clockwise M Circuit diagram SPA connector and female connector, 5-pin Connector Assignment Pin 1 Sensor supply +24 V Pin 2 Sensor supply 0 V Pin 3 – Pin 4 Tx/Rx+, RS485 Pin 5 Tx/Rx-, RS485 M16 connector M16 female connector Motor connector, 12-pin Connector Assignment Pin A – Pin B Motor left Pin C Motor right Pin D Speed Pin E – Pin F Key 1 external Pin G Key 2 external Pin H – Pin J – Pin K Error signal Pin L Speed Pin M GND AB D C E F G H J K M L M16 male connector Terminal assignment
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 4 Subject to modification in technic and design. Errors and omissions excepted.30/10/2008 N 142 Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 Dimensions Hollow shaft Ø25 mm Hollow shaft Ø20 mm Fixing pin for bore Ø10 mm M16 female connector M16 male connector 25 H7 (20 H7) 62.5 21.5 8.5 58.5 100 Ø37 40 ±0.2 Ø37 Ø37 20° M16 male connector / motor