N140 IVO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Electronic spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft ø20 mm / ø25 mm – Interface RS485 – Resolution: 2304 steps/revolution ±4096 revolutions – Technical data - electrical ratings Voltage supply 24 VDC ±10 % Current consumption ≤30 mA Display LCD, 7-segment display, 2-lines, backlit Measuring principle Absolute multiturn measuring system Measuring range -999,99...+9999,99 mm Steps per turn 2304 Number of turns 4096 / 12 bit Spindle pitch ≤23 mm Interface RS485 (ASCII protocol) Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Standard DIN EN 61010-1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL/cUL N 140 Technical data - mechanical design Hollow shaft ø20 mm, ø25 mm Operating speed ≤600 rpm (short-term) Protection DIN EN 60529 IP 65 Operating temperature -10...+50 °C Storing temperature -20...+70 °C Relative humidity 80 % non-condensing Torque support Torque pin provided at housing E-connection - Cable output (30 cm) with male/female connector M16, 5-pin Housing type Surface-mount with hollow shaft Dimensions W x H x L 56 x 100 x 62.5 mm Mounting Surface-mount with hollow shaft Weight approx. 200 g Material Polycarbonate black, UL 94V-0 Hollow shaft max. ø25 mm, manual format alignment Display LCD two lines, interface RS485
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 2 Subject to modification in technic and design. Errors and omissions excepted.30/10/2008 N 140 Part number N 140. 1 0 3 A 01 Hollow shaft A Hollow shaft ø25 mm B Hollow shaft ø20 mm Display A Inclined Voltage supply 3 24 VDC E-connection
0 Cable output with M16 connector
1 RS485
Hollow shaft max. ø25 mm, manual format alignment Display LCD two lines, interface RS485 Accessories Connectors and cables (page %S) Z 165.B01 Mating connector M16, 5-pin, less cable Z 165.AW1 Cable connector M16, 5-pin, less cable with integrated terminating resistor 120 Ω Z 165.D05 Data and supply cable M16, Master to N 140, N 141 and N 142, 5 m Z 165.S01 Cable connector M16, 5-pin, less cable Z 165.V01 Coupling cable between M16 and M16, 1 m N 140 spindle position display supports the editing engineer in manual spindle positioning operations. The principal ben- efits of the new electronic spindle position display is saving time in machine setup and editing as well as elimination of errors when aligning formats to new position values. The absolute measuring system captures any change in position even in powerless state. The backlit LCD display provides the editing engineer with all necessary information for ef- ficient editing of new spindle positions. The two-line display shows both current value and target. A little arrow signalizes the editing engineer the direction the spindle must be turned to get to the new position. RS485 serial interface enables network of 32 spindle position displays with PC or PLC. For complete solutions also memory controllers as de- centralized operating and memory terminals are available. Up to 100 format profiles can be stored by teach-in. Upon request the desired profile is recalled and retransmitted upon pressing a button to every spindle position and shown as target.
Description
www.baumerivo.com Spindle Position Displays N 140 Hollow shaft max. ø25 mm, manual format alignment Display LCD two lines, interface RS485 Connector Assignment Pin 1 Sensor supply +24 V Pin 2 Sensor supply 0 V Pin 3 – Pin 4 Tx/Rx+, RS485 Pin 5 Tx/Rx-, RS485 M16 connector M16 female connector Terminal assignment Dimensions Hollow shaft Ø25 mm Hollow shaft Ø20 mm Fixing pin for bore Ø10 mm M16-female connector M16 connector 25 H7 (20 H7) 62.5 21.5 8.5 58.5 100 Ø37 40 ±0.2 Ø37 Ø37 20°
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 4 Subject to modification in technic and design. Errors and omissions excepted.30/10/2008 N 140 Hollow shaft max. ø25 mm, manual format alignment Display LCD two lines, interface RS485