MTFDDAK256TBN MICRON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 41
Technical content
Features
- Micron ® 3D TLC NAND Flash
- RoHS-compliant package
- SATA 6 Gb/s interface
- TCG/Opal 2.0-compliant self-encrypting drive (SED)
- Compatible with Microsoft eDrive ®
- Hardware-based AES-256 encryption engine
- ATA modes supported – PIO mode 3, 4 – Multiword DMA mode 0, 1, 2 – Ultra DMA mode 0, 1, 2, 3, 4, 5, 6
- Industry-standard, 512-byte sector size support
- Hot-plug/hot-remove capable (2.5")
- Device sleep (DEVSLP), extreme low-power mode
- Native command queuing support with 32-com- mand slot support
- ATA-8 ACS3 command set compliant
- ATA security feature command set and password login support
- Secure erase (data page) command set: fast and se- cure erase
- Sanitize device feature set support
- Self-monitoring, analysis, and reporting technology (SMART) command set
- Dynamic write acceleration
- Adaptive thermal monitoring
- Power loss protection for data-at-rest
- Performance 1, 2 – PCMark ® Vantage (HDD test suite score): Up to 84,000 – Sequential 128KB READ: Up to 530 MB/s – Sequential 128KB WRITE: Up to 500 MB/s – Random 4KB READ: Up to 55,000 IOPS – Random 4KB WRITE: Up to 83,000 IOPS – READ/WRITE latency: 85µs/40µs (TYP)
- Reliability – MTTF: 1.5 million device hours 3 – Static and dynamic wear leveling – Uncorrectable bit error rate (UBER): <1 sector per 1015 bits read
- Low power consumption – Device Sleep numbers: <4mW – DIPM numbers: 110mW TYP 4
- Endurance: Total bytes written (TBW) – 120TB
- Capacity (unformatted): 128GB
- 2.5-inch × 7mm form factor
- Secure firmware update with digitally signed firm- ware image
- Operating temperature – Commercial (0°C to +70°C) 5 Notes: 1. Typical I/O performance numbers as meas- ured fresh-out-of-the-box (FOB) using Iome- ter with a queue depth of 32 and write cache enabled. 2. 4 KB transfers used for READ/WRITE latency values. 3. The product achieves a mean time to failure (MTTF) based on population statistics not relevant to individual units. 4. Active average power measured during exe- cution of MobileMark® with DIPM (device- initiated power management) enabled. 5. Temperature measured by SMART attribute 194. Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties. 1100 2.5-Inch and M.2 NAND Flash SSD
1100_ssd.pdf - Rev. D 10/17 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice.
Part Numbering Information Micron’s 1100 SSD is available in different configurations and densities. The chart below is a comprehensive list of options for the 1100 series devices; not all options listed can be combined to define an offered product. Visit www.micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AK 256 T BN - 1 AR 1 ES Micron Technology Product Family FD = Flash drive Drive Interface D = SATA 6.0 Gb/s Drive Form Factor AK = 2.5-inch (7mm) AV = M.2 (80mm x 22mm) Drive Density 256 = 256GB 512 = 512GB 1T0 = 1024GB 2T0 = 2048GB NAND Flash Type T = TLC Product Family BN = 1100 Production Status Blank = Production ES = Engineering sample Customer Designator YY = Standard Feature Set AB = Standard TA = TAA Compliant ZZ = Blank Extended Firmware Features Z = Non-Encrypted 2 = SED (self-encrypting drive) Sector Size 1 = 512 byte NAND Flash Component AR = 384Gb, TLC, x16, 1.8V (3D) For example: 1 = 1st generation 2 = 2nd generation
2 AB YY
1100 2.5-Inch and M.2 NAND Flash SSD 1100_ssd.pdf - Rev. D 10/17 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Micron’s solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and up to four channels of Micron NAND Flash internally. Available in both M.2 and 2.5-inch form factors, the SSD integrates easily in existing storage infra- structures. The SSD is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth-focused performance. SSD technology enables en- hanced boot times, faster application load times, reduced power consumption and ex- tended reliability. The self-encrypting drive (SED) features a FIPS-compliant, AES-256 encryption engine, providing hardware-based, secure data encryption, with no loss of SSD performance. This SED follows the TCG/Opal specification for trusted peripherals. When TCG/Opal features are not enabled, the device can perform alternate data en- cryption by invoking the ATA security command set encryption features, to provide full- disk encryption (FDE) managed in the host system BIOS. TCG/Opal and ATA security feature sets cannot be enabled simultaneously. The data encryption is always running; however, encryption keys are not managed and the data is not secure until either TCG/Opal or ATA security feature sets are enabled. Figure 2: Functional Block Diagram NAND SATA NAND NAND SSD controller DRAM buffer NAND 1100 2.5-Inch and M.2 NAND Flash SSD General Description CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Measured performance can vary for a number of reasons. The major factors affecting drive performance are the capacity of the drive and the interface of the host. Addition- ally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration. For SSDs designed for the client computing market, Micron specifies performance in fresh-out-of-box (FOB) state. Data throughput measured in steady state may be lower than FOB state, depending on the nature of the data workload. For a description of these performance states and of Micron's best practices for per- formance measurement, refer to Micron's technical marketing brief, Best Practices for SSD Performance Measurement. Table 1: Drive Performance Capacity 256GB 512GB 1024GB 2048GB UnitInterface Speed 6 Gb/s PCMark vantage 84,000 84,000 84,000 84,000 HDD score Sequential read (128KB transfer) 530 530 530 530 MB/s Sequential write (128KB transfer) 500 500 500 500 MB/s Random read (4KB transfer) 55,000 92,000 92,000 92,000 IOPS Random write (4KB transfer) 83,000 83,000 83,000 83,000 IOPS READ latency (TYP) 85 85 85 85 µs WRITE latency (TYP) 40 40 40 40 µs Notes: 1. Performance numbers are maximum values, except as noted. 2. Typical I/O performance numbers as measured using Iometer with a queue depth of 32 and write cache enabled. Fresh-out-of-box (FOB) state is assumed. For performance measurement purposes, the SSD may be restored to FOB state using the SECURE ERASE command. 3. Iometer measurements are performed on an 20GB span of logical block addresses (LBAs). 4. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values with write cache enabled. 5. System variations will affect measured results. For comparison, PCMark scores are meas- ured with the SSD as a secondary drive in a two-drive system. When measured as an OS drive, system overhead can cause lower scores. 1100 2.5-Inch and M.2 NAND Flash SSD Performance CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified capacity. Standard LBA settings, based on the IDEMA standard (LBA1-03), are shown below. Table 2: Standard LBA Settings Capacity Total LBA Max LBA User Available Bytes Decimal Hexadecimal Decimal Hexadecimal (Unformatted) 256GB 500,118,192 1DCF32B0 500,118,191 1DCF32AF 256,060,514,304 512GB 1,000,215,216 3B9E12B0 1,000,215,215 3B9E12AF 512,110,190,592 1024GB 2,000,409,264 773BD2B0 2,000,409,263 773BD2AF 1,024,209,543,168 2048GB 4,000,797,360 EE7752B0 4,000,797,359 EE7752AF 2,048,408,248,320 1100 2.5-Inch and M.2 NAND Flash SSD Logical Block Address Configuration CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Micron’s SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmware-based static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is de- fined as data that is reported as successfully programmed to the SSD but when it is read out of the SSD, the data differs from what was programmed. Table 3: Uncorrectable Bit Error Rate Uncorrectable Bit Error Rate Operation <1 sector per 1015 bits read READ Mean Time To Failure Mean time to failure (MTTF) for the SSD can be predicted based on the component reli- ability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. Table 4: MTTF Capacity MTTF (Operating Hours)1 256GB 1.5 million 512GB 1024GB 2048GB Note: 1. The product achieves a mean time to failure (MTTF) of 1.5 million hours, based on popu- lation statistics not relevant to individual units. 1100 2.5-Inch and M.2 NAND Flash SSD Reliability CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Endurance for the SSD can be predicted based on the usage conditions applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficiency of the drive. The table below shows the drive lifetime for each SSD capacity by client computing and sequential input and based on predefined usage conditions. Table 5: Drive Lifetime – Client Computing Capacity Drive Lifetime (Total Bytes Written) 256GB 120TB 512GB 240TB 1024GB 400TB 2048GB Notes: 1. Total bytes written validated with the drive 90% full. 2. SSD volatile write cache is enabled. 3. Access patterns used during reliability testing are 25% sequential and 75% random and consist of the following: 1% are 512B; 44% are 4 KiB; 35% are 64 KiB; and 20% are 128 KiB. 4. Host workload parameters, including write cache settings, I/O alignment, transfer sizes, randomness, and percent full, that are substantially different than the described notes may result in varied endurance results. 5. GB/day can be calculated by dividing the total bytes written value by the number of days in the interval of interest (365 days × number of years). For example: 100 TB/3 years/365 days = 91 GB/day for 3 years. 1100 2.5-Inch and M.2 NAND Flash SSD Reliability CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Electrical Characteristics
Environmental conditions beyond those listed may cause permanent damage to the de- vice. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 6: SATA Power Consumption Capacity Device Sleep Typical Idle Average Active Average Active Maximum (128KB transfer) Unit 256GB 2 55 70 3000 mW 512GB 4000 1024GB 4 65 75 5000 mW 2048GB 25 110 150 6000 Notes: 1. Data taken at 25°C using a 6 Gb/s SATA interface. 2. Active average power measured while running MobileMark productivity suite. 3. Device-initiated power management (DIPM) enabled. DIPM slumber and DEVSLP ena- bled. 4. Active maximum power is an average power measurement performed using Iometer with 128KB sequential write transfers. Table 7: Maximum Ratings Parameter/Condition Symbol Min Max Unit Notes Voltage input, 2.5-inch V5 4.5 5.5 V – Voltage input, M.2 3V3 3.14 3.46 V – Operating temperature TC 0 70 °C 1 Non-operating temperature – –40 85 °C – Rate of temperature change – – 20 °C/hour – Relative humidity (non-condensing) – 5 95 % – Note: 1. Operating temperature is best measured by reading the SSD's on-board temperature sensor, which is recorded in SMART attribute 194 (0xC2). Table 8: Shock and Vibration Parameter/Condition Specification Non-operating shock 1500G/0.5ms Non-operating vibration 5–800Hz @ 3.10G 1100 2.5-Inch and M.2 NAND Flash SSD 1100_ssd.pdf - Rev. D 10/17 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Dynamic Write Acceleration Dynamic write acceleration optimizes SSD performance for typical client-computing environments, where WRITE operations tend to occur in bursts of commands with idle time between these bursts. Capacity for accelerated performance is derived from the adaptive usage of the SSD's native NAND array, without sacrificing user-addressable storage. Recent advances in Micron NAND technology enable the SSD firmware to achieve acceleration through on- the-fly mode switching between SLC and TLC modes to create a high-speed SLC pool that changes in size and location with usage conditions. During periods of idle time between write bursts, the drive may free additional capacity for accelerated write performance. The amount of accelerated capacity recovered dur- ing idle time depends on the portion of logical addresses that contain user data and other runtime parameters. In applications that do not provide sufficient idle time, the device may need to perform SLC-to-TLC data migration during host activity. Under accelerated operation, write performance may be significantly higher than non- accelerated operations. Power consumption per-byte written is lower during acceler- ated operation, which may reduce overall power consumption and heat production. 1100 2.5-Inch and M.2 NAND Flash SSD Dynamic Write Acceleration CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Adaptive Thermal Monitoring The device features adaptive thermal monitoring. While most host computers exhibit operating environments that keep an SSD running in the range of 40°C to 45°C, adap- tive thermal monitoring enables the SSD to operate in a wide variety of environments by helping to prevent the host computer from running at excessive temperatures. Adaptive thermal monitoring reduces total SSD power consumption by the device con- troller, as well as the NAND media, by injecting time-based delays between internal processing of media commands when the device temperature reaches 75°C. The delay times used are bound to the microsecond range and are based on a proportional and differential control equation of the general form shown here: u(t) = Kp × T p (t) + Kd × dT d dt The delay-control equation is tuned for a steady-state temperature target, which has been designed as an optimum balance of hardware temperature tolerances and drive performance. Steady-state temperature targets are hardware-configuration dependent and may range around 80°C. Temperatures below the intended steady-state target will not produce a proportional component delay, but may produce a differential compo- nent based on the current rate of temperature change according to the control equa- tion. When the feature is active, DRAM refresh rates are also adjusted to improve data integrity and stability while operating outside of temperature specifications. When the device temperature falls below 73°C, normal operation will continue without induced delays. If the temperature continues to rise above the temperature target and exceeds a hardware-dependent critical threshold, the device will abort host commands to prevent component damage. The critical threshold values have a 5°C margin on top of the target threshold of 85°C. Device temperature values used by the adaptive thermal monitoring feature are based on an internal temperature sensor located on the device PCB and may differ from case or package temperatures as measured by a thermocouple. Device temperature is acces- sible through SMART attribute 194, though usage of the SMART feature is not necessary for adaptive thermal monitoring functionality. Adaptive thermal monitoring does not change the current negotiated speed of the SATA bus, nor require or cause any new commands to be issued on the SATA bus. Rated throughput performance is not guaranteed at any point above the maximum specified operating temperature. 1100 2.5-Inch and M.2 NAND Flash SSD Adaptive Thermal Monitoring CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 9: TCG/Opal Support Parameters Property Supported? Comments TCG Storage Specifications OPAL: TCG Storage Security SubSystem Class Specification 2.00 Revision 1.00, Feb 24, 2012 TCG Core Specification Specification 2.00 Revision 2.00, Nov 4, 2011 TCG Storage Interface Interactions Specifi- cation TCG Reference Specification Specification Version 1.02 Revision 1.00 30 Decem- ber, 2011 OPAL SSC 1.00 (backward compatibility) Not supported – OPAL SSC Additional Feature Set Specification Additional DataStore Table Supported Specification 1.00 Revision 1.00, Feb 24, 2012 Single User Mode Supported Specification 1.00 Revision 1.00, Feb 24, 2012 TCG Storage Protection Mechanisms for Secrets Supported Specification Version 1.00 Revision 1.07 17 August, 2011 PSID – Physical Presence SID Supported Specification Version 1.00 Committee Draft Revi- sion 1.05 February 9, 2011 GUDID (Globally Unique Serial Number) Supported Mandatory GUDID Proposal 11/03/2011 (Microsoft) SID Authority Disable Supported SID Authority Disable Proposal 9/26/2011 (Micro- soft) Modifiable CommonName Columns Supported Modifiable CommonName Columns Proposal 7/22/2010 (Microsoft) OPAL SSC Feature Set – Specific List ALL OPAL Mandatory Features Supported – Close Session (optional) Supported Allows TPer to notify the host it has aborted a ses- sion Restricted Command & Table (optional) Not Supported The interface control template enables TPer control over selected interface commands; the benefit is the reduction of undesired side effects Type Table (not required) Not Supported – Activate Method Supported – Revert Method Supported – Revert SP Method Supported – Activate Method Within Transactions Not Supported As per OPAL, this behavior is out of the scope Revert Method within Transactions Not Supported As per OPAL, this behavior is out of the scope Revert SP Method within Transactions Not Supported As per OPAL, this behavior is out of the scope Creation/Deletion of Tables/Rows after Manufacturing Not Supported As per OPAL, this behavior is out of the scope TPer Feature COM ID Management Support Not Supported Dynamic COM ID allocation & management not supported Buffer Management Support Not Supported Flow control 1100 2.5-Inch and M.2 NAND Flash SSD TCG/Opal Support CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 9: TCG/Opal Support Parameters (Continued) Property Supported? Comments ACK/NACK Support Not Supported Session reliability Async Support Not Supported Asynchronous protocol support with multiple com- mands per session Geometry Reporting Feature ALIGN Supported Alignment is not required Logical Block Size 512 bytes Logical block size = 512 bytes Alignment Granularity 512 bytes Logical block size = 512 bytes Lowest Aligned LBA 0 – OPAL SSC V2.00 Feature Descriptor Base COM ID 0x1000 0x1000-0xFFFF defined for COM ID management Number of COM IDs 1 – Range Crossing Behavior 0 If drive receives a READ or WRITE command that spans multiple LBA ranges and the LBA ranges are not locked, then: 1. Process the data transfer, if Range Crossing = 0 2. Terminate the command with “Other Invalid Command Parameter” if Range Crossing = 1 Number of Locking SP Admin Authorities Supported 4 As per OPAL 2.0, drive should support at least 4 ad- min Number of Locking SP User Authorities Supported 16 As per OPAL 2.0, drive should support at least 8 users Initial C_PIN_SID PIN Indicator 0x00 0x00 = The initial C_PIN_SID PIN value is equal to the C_PIN_MSID PIN value 0xFF = The initial C_PIN_SID PIN value is VU, and MAY not be equal to the C_PIN_MSID PIN value OPAL 2.0 (only) Customer-specific SID – Configurable Behavior of C_PIN_SID PIN upon Ter Revert 0x00 0x00 = The C_PIN_SID PIN value becomes the value of the C_PIN_MSID PIN column after successful in- vocation of revert on the admin SP’s object in the SP table 0xFF = The C_PIN_SID PIN value changes to a VU value after successful invocation of revert on the admin SP’s object in the SP table and MAY not be equal to the C_PIN_MSID PIN value OPAL 2.0 (only) DataStore Table Feature Maximum number of DataStore Tables 16 The maximum number of the DataStore tables that the TPer supports, including the DataStore table defined in OPAL SSC 2.0 Maximum total size of DataStore Tables 12MB Specifies the maximum total size in bytes of all of the DataStore tables that TPer supports, including the DataStore table defined in OPAL SSC 2.0 MBR Table 128MB – 1100 2.5-Inch and M.2 NAND Flash SSD TCG/Opal Support CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 9: TCG/Opal Support Parameters (Continued) Property Supported? Comments Byte Table Access Granularity Mandatory Write Granularity 1 TPer enforces when the host invokes the set meth- od on byte tables; it should be less than or equal to 8192; it should be less than or equal to Recommen- ded Access Granularity, OPAL 2.0 (only) Recommended Access Granularity 8192 TPer recommends when the host invokes the set or get method on byte tables; it should be less than or equal to 8192 Cryptographic Features AES Key Size 256 Bits AES key is generated by using CTR DRBG algorithm (FIPS Compliant) AES Mode XTS IV swapped Number of Ranges/Band Supported 16 Unique AES key per range/band; range crossing is allowed if the range is unlocked Re-Encryption Not Supported – Key Management Cryptographic Crypto Erase Completion Time <1s Yes – Cryptographic Algorithms are Certified by FIPS-197 No Designed to meet, no plans for certification AES 256-Bit CBC/ECB Mode Supported ECB mode used only for generating the random key by CTR DRBG CTR DRBG Supported – SHA 256 Supported – RSA 2048 Signature Verification Supported – TPer Communication Properties Max ComPacket Size 131072 256 sectors (128K) Max Response ComPacket Size 131072 256 sectors (128K) Max Packet Size 128512 – Max Individual Token Size 123904 – Max Packets 1 – Max SubPackets 1 – Max Sessions 1 Each session requires a set of buffers and variables Max Transaction Limit 1 Transaction are inside sessions Max Methods 1 Methods are contained in a transaction Max Authentications 21 21 = 16 users + 4 admins + 1 anybody Def Session Timeout Yes The session timeout length (in milliseconds) used by the TPer by default IEEE1667 Probe Silo Supported – TCG Storage Silo Supported – 1100 2.5-Inch and M.2 NAND Flash SSD TCG/Opal Support CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 9: TCG/Opal Support Parameters (Continued) Property Supported? Comments Other than Probe and TCG Storage Silo Not Supported – IEEE1667 Major Version 2 – IEEE1667 Minor Version 0 – Maximum P_OUT Transfer Size 131072 256 sectors (128K) Others FDE (ATA Security with Key Management) Yes – Secure Firmware Download Supported Firmware image is validated by using SHA256 and RSA2048 algorithm 1100 2.5-Inch and M.2 NAND Flash SSD TCG/Opal Support CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
0 General configuration bit-significant information
15 F 0b 0 = ATA device
14–8 X 0000100b Retired
7 F 0b Obsolete
6 F 1b Obsolete
5–3 X 000b Retired
2 V 0b Response incomplete
1 X 0b Retired
0 F 0b Reserved
2 F C837h Specific configuration
3 F 0010h Obsolete
4 F 0000h 0000h Retired
6 F 003Fh Obsolete
7 (O)V 0000h 0000h Reserved for assignment by the CompactFlash™ Association
9 X 0000h Retired
10 (M)F varies Serial number (20 ASCII characters)
20 X 0000h 0000h
23 (M)F varies Firmware revision (8 ASCII characters) 27 (M)F varies Model number (40 ASCII characters) 47 15–8 F 80h 80h 7–0 F 10h 00h = Reserved 01h-FFh = Maximum number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands.
48 Trusted Computing feature set options
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13–1 F 0000000000000b Reserved for the Trusted Computing Group
0 F varies 1 = Trusted Computing feature set is supported
This bit will be 1 for TCG drives, otherwise 0 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
49 Capabilities
15–14 F 00b Reserved for the IDENTIFY PACKET DEVICE command
13 F 1b 1 = Standby timer values as specified in this standard are sup-
0 = Standby timer values shall be managed by the device
12 F 0b Reserved for the IDENTIFY PACKET DEVICE command
11 F 1b 1 = IORDY supported
0 = IORDY may be supported 10 F 1b 1 = IORDY may be disabled.
9 F 1b 1 = LBA supported
8 F 1b 1 = DMA supported
7–2 F 000000b Retired 1–0 F 00b Long physical sector alignment error reporting
50 Capabilities
13–2 F 000000000000b Reserved
1 X 0b Obsolete
0 F 1b Shall be set to one to indicate a vendor specific standby timer
51 X 0000h 0000h Obsolete
53 15–8 F 00000000b Free-fall control sensitivity 7–3 F 00000b Reserved 2 F 1b 1 = The fields reported in word 88 are valid. 0 = The fields reported in word 88 are not valid. 1 F 1b 1 = The fields reported in words (70:64) are valid. 0 = The fields reported in words (70:64) are not valid.
0 X 1b Obsolete
54 X 3FFFh 0010h
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 59 15 F 1b 1 = The BLOCK ERASE EXT command is supported. 14 F 0b 1 = The OVERWRITE EXT command is supported. 13 F varies 1 = The CRYPTO SCRAMBLE EXT command is supported. This bit will be 1 for TCG drives, otherwise 0 12 F 1b 1 = The Sanitize feature set is supported.
11 F 0b Commands allowed during a sanitize operation are as speci-
10 F 0b SANITIZE ANTIFREEZE LOCK EXT command is supported
9 F 0b Reserved
8 V 1b 1 = Multiple sector setting is valid. 7–0 V 00010000b xxh = Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands 60–61 M(F) Varies by capacity Total number of user addressable logical sectors
62 X 0000h Obsolete
63 15–11 F 00000b Reserved 10 V 0b 1 = Multiword DMA mode 2 is selected. 0 = Multiword DMA mode 2 is not selected. 9 V 0b 1 = Multiword DMA mode 1 is selected. 0 = Multiword DMA mode 1 is not selected. 8 V 0b 1 = Multiword DMA mode 0 is selected. 0 = Multiword DMA mode 0 is not selected. 7–3 F 0000b Reserved 2 F 1b 1 = Multiword DMA mode 2 and below are supported. 1 F 1b 1 = Multiword DMA mode 1 and below are supported. 0 F 1b 1 = Multiword DMA mode 0 is supported. 64 15–2 F 00000000000000b Reserved 1–0 F 11b PIO modes supported
65 F 0078h Minimum Multiword DMA transfer cycle time per word
66 F 0078h Manufacturer's recommended Multiword DMA transfer cycle
67 F 0078h Minimum PIO transfer cycle time without flow control
68 F 0078h Minimum PIO transfer cycle time with IORDY flow control
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
69 Additional Supported
15 F 0b 1 = CFast Specification Support
14 F 1b 1 = Deterministic read after Trim is supported.
13 F 0b 1 = Long Physical Sector Alignment Error Reporting Control is
supported.
12 F 0b Obsolete
11 F 1b 1 = READ BUFFER DMA is supported. 10 F 1b 1 = WRITE BUFFER DMA is supported.
9 F 0b Obsolete
8 F 1b 1 = DOWNLOAD MICROCODE DMA is supported.
7 F varies 1 = IEEE-1667 supported
6 F 0b 1 = Optional ATA device 28-bit commands supported
5 F 1b 1 = Read zero after Trim is supported
4 F Varies 1 = Device encrypts all user data
3 F 1b 1 = Extended number of user addressable sectors is supported.
2 F 0b 1 = All write cache is nonvolatile
1–0 F 00b Reserved
70 F 0000h Reserved
71 F 0000h 0000h
Reserved for the IDENTIFY PACKET DEVICE command
75 Queue depth
15–5 F 00000000000b Reserved 4–0 F 11111b Maximum queue depth - 1 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
76 Serial ATA capabilities
15 F 1b 1 = Supports READ LOG DMA EXT as equivalent to READ LOG
14 F 0b 1 = Supports device automatic partial to slumber transitions
13 F 0b 1 = Supports host automatic partial to slumber transitions
12 F 1b Supports Native Command Queuing priority information
11 F 0b Supports Unload while NCQ commands outstanding
10 F 1b Supports Phy event counters
9 F 0b Supports receipt of host initiated interface power manage-
8 F 1b Supports Native Command Queueing
7–4 F 0000b Reserved for Serial ATA 3 F 1b 1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s) 2 F 1b 1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s) 1 F 1b 1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)
0 F 0b Reserved (set to 0)
77 Serial ATA additional capabilities
15–8 F 00000000b Reserved for future Serial ATA definition
7 F 1b 1 = Supports DEVSLP_to_ReducedPwrState
6 F 1b Supports RECEIVE FPDMA QUEUED and SEND FPDMA QUEUED
5 F 0b Supports NCQ Queue Management Command
4 F 0b Supports NCQ Streaming
3–1 V Varies Coded value indicating current negotiated Serial ATA signal speed
0 F 0b Shall be cleared to zero
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
78 Serial ATA features supported
15–12 F 0000b Reserved
11 F 0b 1 = Supports Rebuild Assist
10 F 0b 1 = Supports Device Initiated Interface Power Management
Software Settings Preservation
9 F 0b 1 = Supports Hybrid Information
8 F 1b 1 = Device sleep supported
7 F 0b 1 = Supports NCQ Autosense
6 F 1b 1 = Supports software settings preservation
5 F 0b 1 = HARDWARE FEATURE CONTROL SUPPORTED bit
4 F 0b 1 = Supports in-order data delivery
3 F 1b 1 = Supports device initiate interface power management
2 F 1b 1 = Supports DMA Setup Auto-Activate optimization
1 F 0b 1 = Supports non-zero buffer offsets in DMA Setup FIS
79 Serial ATA features enabled
15–12 V 0000b Reserved
11 V 0b 1 = Rebuild Assist enabled
10 V 0b Reserved
9 V 0b 1 = Hybrid Information feature is enabled
8 V 0b 1 = Device sleep enabled
7 V 0b 1 = Device automatic partial to slumber transitions enabled
6 V 1b 1 = Software settings preservation enabled
5 V 0b 1 = Hardware feature control is enabled
4 V 0b 1 = In-order data delivery enabled
3 V 0b 1 = Device initiating interface power management enabled
2 V 0b 1 = DMA Setup Auto-Activate optimization enabled
1 V 0b 1 = Non-zero buffer offsets in DMA Setup FIS enabled
0 V 0b Reserved (set to 0)
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
80 Major revision number
15–11 F 00000b Reserved
10 F 1b 1 = Supports ACS-3
9 F 1b 1 = Supports ATA8-ACS2
8 F 1b 1 = Supports ATA8-ACS
7 F 1b 1 = Supports ATA/ATAPI-7
6 F 1b 1 = Supports ATA/ATAPI-6
5 F 1b 1 = Supports ATA/ATAPI-5
4 F 1b Obsolete
3 F 1b Obsolete
2 S 0b Obsolete
1 S 0b Obsolete
81 F 006Dh Minor revision number
006Dh = ACS-3 version 5
82 Command set supported
15 X 0b Obsolete
14 F 1b 1 = NOP command supported
13 F 1b 1 = READ BUFFER command supported
12 F 1b 1 = WRITE BUFFER command supported
11 X 0b Obsolete
10 X 0b Obsolete
9 F 0b 1 = DEVICE RESET command supported
8 F 0b Obsolete
6 F 1b 1 = Read look-ahead supported
5 F 1b 1 = Write cache supported
4 F 0b Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3 F 1b 1 = Mandatory Power Management feature set supported
2 F 0b Obsolete
1 F 1b 1 = Security feature set supported
0 F 1b 1 = SMART feature set supported
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
83 Command set supported
13 F 1b 1 = FLUSH CACHE EXT command supported
12 F 1b 1 = Mandatory FLUSH CACHE command supported
10 F 1b 1 = 48-bit address feature set supported
8 X 0b Obsolete
6 F 0b 1 = SET FEATURES subcommand required to spin-up after pow-
5 F 0b 1 = Power-Up In Standby feature set supported
4 F 0b Obsolete
3 F varies 1 = Advanced Power Management feature set supported
2 F 0b 1 = CFA feature set supported
1 F 0b Obsolete
0 F 1b 1 = DOWNLOAD MICROCODE command supported
84 Command set/feature supported extension
13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
11 F 0b Obsolete
10–9 F 00b Obsolete
8 F 1b 1 = 64-bit word wide name supported
6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT com-
5 F 1b 1 = General Purpose Logging feature set supported
4 F 0b 1 = Streaming feature set supported
3 F 0b Obsolete
2 F 0b Reserved
1 F 1b 1 = SMART self-test supported
0 F 1b 1 = SMART error logging supported
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 85 Command set/feature enabled.
8 V 0b Obsolete
7 V 0b Obsolete
6 V 1b 1 = Read look-ahead enabled
5 V 1b 1 = Write cache enabled
set is not supported.
3 F 1b Power Management feature set is supported
1 V 0b 1 = Security Mode feature set enabled
0 V 1b 1 = SMART feature set enabled
86 Command set/feature enabled.
15 F 1b 1 = Words 120-119 are valid
14 F 0b 1 = Reserved
12 F 1b 1 = FLUSH CACHE command supported
10 F 1b 1 = 48-bit Address features set supported
9 V 0b Obsolete
5 V 0b 1 = Power-Up In Standby feature set enabled
4 V 0b Obsolete
3 V 1b 1 = Advanced Power Management feature set enabled
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
87 Command set/feature enabled/supported
12 V 0b Obsolete
11 V 0b Obsolete
10–9 F 00b Obsolete
3 V 0b Obsolete
2 V 0b 1 = Media serial number is valid
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
88 Ultra DMA modes
14 0b 1 = Ultra DMA mode 6 is selected 0 = Ultra DMA mode 6 is not selected 13 0b 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 12 0b 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 11 0b 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 10 0b 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 9 0b 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 8 0b 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected 7 0b Reserved 6 1b 1 = Ultra DMA mode 6 and below are supported 5 1b 1 = Ultra DMA mode 5 and below are supported 4 1b 1 = Ultra DMA mode 4 and below are supported 3 1b 1 = Ultra DMA mode 3 and below are supported 2 1b 1 = Ultra DMA mode 2 and below are supported 1 1b 1 = Ultra DMA mode 1 and below are supported 0 1b 1 = Ultra DMA mode 0 IS supported 89 (O)F 0001h Time required for security erase unit completion 90 (O)F 0001h Time required for enhanced security erase completion 91 (O)V 00FEh Current advanced power management value 92 (O)V FFFEh Master Password Identifier
93 F 0000h Shall be 0000h for SATA devices
94 F 0000h Obsolete
95 (O)V 0000h Stream Minimum Request Size 96 (O)V 0000h Streaming Transfer Time – DMA 97 (O)V 0000h Streaming Access Latency – DMA and PIO 98 (O)F 0000h 0000h Streaming Performance Granularity (98-99)
100 V Varies by capacity Maximum user LBA for 48-bit Address feature set
104 (O)V 0000h Streaming Transfer Time – PIO
105 F 0008h Maximum number of 512-byte blocks of LBA Range Entries
per DATA SET MANAGEMENT command 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
106 Physical sector size/logical sector size
13 F 0b 1 = Device has multiple logical sectors per physical sector
12 F 0b 1 = Device logical sector longer than 256 words
11–4 F 00000000b Reserved 3–0 F 0000b 2^x logical sectors per physical sector 107 (O)F 0000h Inter-seek delay for ISO-7779 acoustic testing in microseconds 108 15–12 F 0101b NAA (3-0) 11–0 000000001010b IEEE OUI (23-12) 109 15–4 F 000001110101b IEEE OUI (11-0) 3–0 Varies Unique ID (35-32) 110 (M)F Varies 5-0 Unique ID (31-16) 111 (M)F Varies Unique ID (15-0) 112 (O)F 0000h 0000h 0000h 0000h Reserved for 12- bit word-wide name extension to 128 bits 116 (O) 0000h Obsolete 117 (O)F 0000h 0000h Words per Logical Sector
119 Commands and feature sets supported (continued from words
84–82) 13–10 F 0000b Reserved
9 F 0b 1 = DSN feature set is supported
8 F 1b 1 = Accessible Max address configuration feature set is suppor-
7 F 0b 1 = Extended Power Conditions feature set is supported
6 F 0b 1 = Sense Data Reporting feature set is supported
5 F 0b 1 = Free-fall control feature set is supported
4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is
3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands
2 F 1b 1 = The WRITE UNCORRECTABLE EXT command is supported
1 F 1b 1 = The Write-Read-Verify feature set is supported
0 F 0b Obsolete
1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
120 Commands and feature sets supported or enabled (continued
from words 87–85) 15 0b Shall be cleared to zero 14 1b Shall be set to one 13–10 0000b Reserved 9 0b 1 = DSN feature set is enabled 8 0b Reserved 7 0b 1 = EPC feature set is enabled 6 0b 1 = Sense Data Reporting feature set is enabled 5 0b 1 = Free-fall control feature set is enabled 4 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT com- mands are supported 2 1b 1 = The WRITE UNCORRECTABLE EXT command is supported 1 0b 1 = The Write-Read-Verify feature set is enabled 0 0b Obsolete
121 F 0000h 0000h
Reserved for expanded supported and enabled settings 127 (O) 0000h Obsolete
128 Security status
15–9 F 0000000b Reserved
8 V 0b Security level 0 = High, 1 = Maximum
7–6 F 00b Reserved
5 F 1b 1 = Enhanced security erase supported
4 V 0b 1 = Security count expired
3 V 0b 1 = Security frozen
2 V 0b 1 = Security locked
1 V 0b 1 = Security enabled
0 F 1b 1 = Security supported
129–159 X Vendor specific data Vendor specific
160 X 0000h 0000h
Reserved for assignment by the CompactFlash Association 168 15–4 F 000h Reserved 3-0 F Varies Device Nominal Form Factor 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description
169 DATA SET MANAGEMENT command support
15–1 F 000000000000000 b Reserved
0 F 1b 1 = The Trim bit in the DATA SET MANAGEMENT command is
170 F 0000h 0000h
Additional product identifier
174 F 0000h 0000h Reserved
176 (O)V Varies Current media serial number (60 ASCII characters)
206 SCT Command Transport
15–12 X 0000b Vendor-specific 11–6 F 000000b Reserved
5 F 1b SCT Command Transport Data Tables supported
4 F 1b SCT Command Transport Features Control supported
3 F 0b SCT Command Transport Error Recovery Control supported
2 F 1b SCT Command Transport Write Same supported
0 F 1b SCT Command Transport supported
207 F 0000h 0000h Reserved for CE-ATA
209 (O) Alignment of logical blocks within a larger physical block 13–0 F 00000000000000b Logical sector offset within the first physical sector where the first logical sector is placed 210 (O)V 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only 212 (O)F 0000h 0001h Verify Sector Count Mode 2 Only 214 (O) 0000h Obsolete 215 (O)V 0000h Obsolete 216 (O)V 0000h Obsolete 217 (M)F 0001h Nominal media rotation rate (ATA8-ACS 1699-D Revision 6) 218 (O)V 0000h Reserved
219 Obsolete
220 15–8 F 00h Reserved 7–0 V 00h Write-Read-Verify feature set current mode 221 0000h Reserved 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 222 Transport Major revision number. 0000h or FFFFh = device does not report version 15–12 0001b Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved Parallel (Type = 0) Serial (Type = 1) 11–8 0000b Reserved 7 1b Supports SATA Rev 3.2 6 1b Supports SATA Rev 3.1 5 1b Supports SATA Rev 3.0 4 1b Supports SATA Rev 2.6 3 1b Supports SATA Rev 2.5 2 1b Supports SATA II: Extensions 1 1b Supports SATA 1.0a 0 1b Supports ATA8-APT ATA8-AST 223 (M)F 0000h Transport Minor revision number
224 F 0000h 0000h
230-233 Varies Extended number of user addressable sectors 234 (O)F 0001h Minimum number of 512 byte units per DOWNLOAD MICRO- CODE command for mode 3 235 00FFh Maximum number of 512 byte units per DOWNLOAD MICRO- CODE command for mode 3 236 0000h 0000h 0000h 0000h 0000h 0000h 0000h Reserved 243 15 0b Reserved 14 varies Bit 14 = 1 Supports FDE security features 13-0 00000000000000b Reserved 244 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h Reserved 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 10: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 255 (M)F Integrity word 15–8 Varies Checksum 7–0 A5h Signature Note: 1. F = The content of the word is fixed and does not change. V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device. X = The content of the word may be fixed or variable. R = The content of the word is reserved and will be zero. M = Support of the word is mandatory. O = Support of the word is optional. 1100 2.5-Inch and M.2 NAND Flash SSD Device ID CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 11: Supported ATA Command Set See ACS-3 standard for command details Command Name Command Code (hex) AMAC-GET NATIVE MAX ADDRESS EXT 78h/0000h AMAC-SET ACCESSIBLE MAX ADDRESS EXT 78h/0001h AMAC-FREEZE ACCESSIBLE MAX ADDRESS EXT 78h/0002h CHECK POWER MODE 98h or E5h DATA SET MANAGEMENT – TRIM 06h/0001h DOWNLOAD MICROCODE 92h DOWNLOAD MICROCODE DMA 93h EXECUTE DEVICE DIAGNOSTIC 90h FLUSH CACHE E7h FLUSH CACHE EXT EAh IDENTIFY DEVICE ECh IDLE E3h or 97h IDLE IMMEDIATE E1h or 95h INITIALIZE DEVICE PARAMETERS 91h READ BUFFER E4h READ DMA (with retry) C8h READ DMA (without retry) C9h READ DMA EXT 25h READ FPDMA QUEUED 60h READ LOG EXT 2Fh READ MULTIPLE C4h READ MULTIPLE EXT 29h READ SECTOR(S) EXT 24h READ SECTOR(S) (with retry) 20h READ SECTOR(S) (without retry) 21h READ VERIFY SECTOR(S) EXT 42h READ VERIFY SECTOR(S) (with retry) 40h READ VERIFY SECTOR(S) (without retry) 41h RECEIVE FPDMA QUEUED 65h SANITIZE DEVICE B4h SCT WRITE SAME 02h/0001h 02h/0002h 02h/0101h 02h/0102h SCT SET FEATURE CONTROL 04h/01h SCT RETURN FEATURE CONTROL 04h/02h SCT RETURN FEATURE OPTION FLAG 04h/03h 1100 2.5-Inch and M.2 NAND Flash SSD Commands CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 11: Supported ATA Command Set (Continued) See ACS-3 standard for command details Command Name Command Code (hex) SCT RETURN SCT DATA TABLE 05h/01h SECURITY DISABLE PASSWORD F6h SECURITY ERASE PREPARE F3h SECURITY ERASE UNIT F4h SECURITY FREEZE LOCK F5h SECURITY SET PASSWORD F1h SECURITY UNLOCK F2h SEND FPDMA QUEUED 64h SET FEATURES EFh SET MULTIPLE MODE C6h SLEEP E6h or 99h SMART DISABLE OPERATIONS B0h/D9h SMART ENABLE OPERATIONS B0h/D8h SMART ENABLE/DISABLE AUTOSAVE B0h/D2h SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h SMART READ DATA B0h/D0h SMART READ LOG B0h/D5h SMART RETURN STATUS B0h/DAh SMART WRITE LOG B0h/D6h STANDBY E2h or 96h STANDBY IMMEDIATE E0h or 94h TRUSTED NON-DATA 5Bh TRUSTED RECEIVE 5Ch TRUSTED RECEIVE DMA 5Dh TRUSTED SEND 5Eh TRUSTED SEND DMA 5Fh WRITE BUFFER E8h WRITE DMA (with retry) CAh WRITE DMA (without retry) CBh WRITE DMA EXT 35h WRITE DMA FUA EXT 3Dh WRITE FPDMA QUEUED 61h WRITE LOG EXT 3Fh WRITE MULTIPLE C5h WRITE MULTIPLE EXT 39h WRITE MULTIPLE FUA EXT CEh WRITE SECTOR(S) (with retry) 30h 1100 2.5-Inch and M.2 NAND Flash SSD Commands CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 11: Supported ATA Command Set (Continued) See ACS-3 standard for command details Command Name Command Code (hex) WRITE SECTOR(S) EXT 34h WRITE UNCORRECTABLE EXT 45h 1100 2.5-Inch and M.2 NAND Flash SSD Commands CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
2.5" 7 mm Figure 3: 2.5" 7 mm SSD Interface Connections Power segment Signal segment P1 S1 Table 12: SATA Signal Segment Pin Assignments Signal Name Type Description S1 GND Ground S2 A Differential signal pair A and A# S3 A# S4 GND Ground S5 B# Differential signal pair B and B# S6 B S7 GND Ground Table 13: 2.5-Inch SATA Power Segment Pin Assignments Pin# Signal Name Description P1 RETIRED No connect P2 RETIRED No connect P3 DEVSLP Device sleep P4 GND Ground P5 GND Ground P6 GND Ground P7 V5 5V power, precharge P8 V5 5V power P9 V5 5V power P10 GND Ground P11 DAS Device activity signal P12 GND Ground P13 V12 No connect P14 V12 No connect P15 V12 No connect 1100 2.5-Inch and M.2 NAND Flash SSD Interface Connectors CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
M.2 2280 Figure 4: M.2 2280 SSD Interface Connections P1P75 P67 P57 P21 P11 P74P2 P10 P20 P58 P68 Primary side Secondary side Table 14: M.2 2280 Signal Assignments Primary Side Secondary Side Pin # Signal Name Description Pin # Signal Name Description 1 CONFIG_3 Ground 2 3V3 3.3V 3 GND Ground 4 3V3 3.3V
5 NC No connect 6 NC No connect
7 NC No connect 8 NC No connect
9 NC No connect 10 DAS/DSS Drive activity (host LED)
11 NC No connect Key
21 CONFIG_0 Ground 22 NC No connect
23 NC No connect 24 NC No connect
25 NC No connect 26 NC No connect
27 GND Ground 28 NC No connect
29 NC No connect 30 NC No connect
31 NC No connect 32 NC No connect
33 GND Ground 34 NC No connect
35 NC No connect 36 NC No connect
37 NC No connect 38 DEVSLP Device sleep
39 GND Ground 40 NC No connect
41 SATA +B SATA B
42 NC No connect
43 SATA -B 44 NC No connect
45 GND Ground 46 NC No connect
47 SATA -A SATA A
48 NC No connect
49 SATA +A 50 NC No connect
51 GND Ground 52 NC No connect
53 NC No connect 54 NC No connect
55 NC No connect 56 Reserved Vendor use
57 GND Ground 58 Reserved Vendor use
1100 2.5-Inch and M.2 NAND Flash SSD Interface Connectors CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Table 14: M.2 2280 Signal Assignments (Continued) Primary Side Secondary Side Pin # Signal Name Description Pin # Signal Name Description
67 NC No connect 68 Reserved No connect
69 CONFIG_1 Ground 70 3V3 3.3V 71 GND Ground 72 3V3 3.3V 73 GND Ground 74 3V3 3.3V
75 CONFIG_2 Ground
1100 2.5-Inch and M.2 NAND Flash SSD Interface Connectors CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 36 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
2.5" 7 mm Product mass: 56 grams MAX Physical dimensions conform to the applicable form factor specifications as listed in the figure below. Figure 5: 2.5-Inch Package – 7mm H +0.00/-0.50 L MAX W ±0.25 (3.50) (4.80) (14.00) (90.60) (2X M3) (Both sides) (3.00) (14.00) (90.60) (61.71) (4.07)(4X M3) Note: 1. All dimensions are in millimeters. Table 15: 2.5-Inch Package Dimensions Density (GB) W L H Unit 256 69.85 100.45 7.00 mm 512 1024 2048 Note: 1. Dimension values in millimeter per SFF 8201 Rev. 2.7. 1100 2.5-Inch and M.2 NAND Flash SSD Physical Configuration CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
M.2 2280 Product mass: 10 grams MAX Physical dimensions conform to the applicable form factor specifications as listed in the figure below. Figure 6: M.2 Type 2280 Package Pin 1 Pin 75 A MAX L ±0.15 W ±0.15 B ±0.08 (3.50 DIA) (5.50 DIA) B Note: 1. All dimensions are in millimeters. Table 16: M.2 Type 2280 Package Dimensions Density (GB) Specification W L A B Unit 256 22.00 80.00 1.35 0.80 mm512 1024 S3 1.50 1100 2.5-Inch and M.2 NAND Flash SSD Physical Configuration CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Micron SSDs comply with the following:
- Micron Green Standard
- Built with sulfur resistant resistors
- CE (Europe): EN 55032 Class B, RoHS
- FCC: CFR Title 47, Part 15 Class B
- UL/cUL: approval to UL-60950-1, 2nd Edition, IEC 60950-1:2005 (2nd Edition); EN 60950-1 (2006) + A11:2009+ A1:2010 + A12:2011 + A2:2013
- BSMI (Taiwan): approval to CNS 13438 Class B and CNS 15663
- RCM (Australia, New Zealand): AS/NZS CISPR32 Class B
- KC RRL (Korea): approval to KN32 Class B, KN 35 Class B may apply to customers who place these products in the markets where WEEE is en- forced.
- TUV (Germany): approval to IEC60950/EN60950
- VCCI (Japan): 2015-04 Class B
- IC (Canada): ICES-003 Class B - This Class B digital apparatus complies with Canadian ICES-003. - Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea- sonable protection against harmful interference in a residential installation. This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a partic- ular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas- ures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the re- ceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. 1100 2.5-Inch and M.2 NAND Flash SSD Compliance CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 39 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
- Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org
- SATA 3.2 GOLD
- ATA-8 ACS3 (T13/2161-D, Revision 5)
- TCG Storage Security Subsystem Class Opal; Specification 2.00 Revision 1.00, Feb 24, 2012
- TCG Core Specification; Specification 2.00 Revision 2.00, Nov 4, 2011
- TCG Storage Interface Interactions: Specification Version 1.02 Revision 1.00 30 De- cember, 2011
- IEEE-1667: "Standard Protocol for Authentication in Host Attachments of Transient Storage Devices"
- SFF 8201 Rev 2.7: For form factor
- PCI Express M.2 Specification rev 1.0: For form factor
- Trade Agreements Act of 1979 (19 U.S.C. 2501) 1100 2.5-Inch and M.2 NAND Flash SSD References CCMTD-1725822587-10292 1100_ssd.pdf - Rev. D 10/17 EN 40 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.
Revision History
Rev. D – 10/17
- Updated the certifications list
- Updated Table 10, Word 83 to reflect both APM ON & OFF available options Rev. C – 12/16
- Added TAA Compliant option
- Updated pin names for M.2 in Table 14 Rev. B – 5/16
- Updated random 4KB read IOPS
- Updated Adaptive Thermal Monitoring, TCG/Opal Support and Device ID sections
- Updated doc ID number
- Misc. documentation edits Rev. A – 12/15
- Initial release 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000 www.micron.com/products/support Sales inquiries: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization some- times occur. 1100 2.5-Inch and M.2 NAND Flash SSD
1100_ssd.pdf - Rev. D 10/17 EN 41 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2015 Micron Technology, Inc. All rights reserved.