MSK186 MSK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
4707 Dey Road Liverpool, N.Y. 13088 (315) 701-6751 FEATURES: Space Efficient Dual Amplifier High Voltage Operation: Single Supply: +8V to +60V Dual Supply: ±4V to±30V High Output Current: 8 Amp Continuous Per Amplifier High Speed: 9V/µS Low Quiescent Current: 26 mA Per Amplifier Typ. Adjustable Current Limits Thermal Shutdown Enable/Status Pin For Output Disable Control Available with Three Lead Form Configurations Contact MSK for MIL-PRF-38534 Qualification Status MIL-PRF-38534 CERTIFIED 186 Servo Driver Actuator Driver Audio Amplifier Power Supplies Bridge Amps Stereo Amps M.S.KENNEDY CORP. DESCRIPTION: The MSK 186 is a dual high power operational amplifier ideal for use with a wide variety of loads. With operation from either single or dual supplies, it offers excellent design flexibility. Power dissipation is kept to a minimum with a quiescent current rating of only 26mA per amplifier, while 8 Amps of continuous available output current makes it a very good low cost choice for motor drive circuits and audio amplification. The design is internally protected against current overloads and overtemperature conditions. The current limit can also be user-selected through the use of a resistor/potentiometer or voltage out/current out DAC. The MSK 186 is packaged in a hermetically sealed, isolated 18 pin power DIP with bolt down tabs for applications that require heat sinking. TYPICAL APPLICATIONS PRELIMINARY Rev. B 11/061 DUAL HIGH VOLTAGE/ VERY HIGH CURRENT OPERATIONAL AMPLIFIER EQUIVALENT SCHEMATIC -VCC 1 +VCC 1 OUTPUT 1 OUTPUT 2 -VIN 2 +VIN 2 VR 2 ILIM 2 E/S 2 PIN-OUT INFORMATION E/S 1 ILIM 1 VR 1 +VIN 1 -VIN 1 OUTPUT 2 OUTPUT 2 +VCC 2 -VCC 2
Peak Output Current (within S.O.A.) Input Voltage Input Voltage Junction Temperature 60V 10A (-VCC)-0.5V to (+VCC)+0.5V (-VCC)-0.1V to (+VCC)-3V Internal Protection (See Application Note Storage Temperature Range Lead Temperature Range (10 seconds) Case Operating Temperature MSK186H/E MSK186 Thermal Resistance (Per Amplifier) Junction to Case @ 125°C STATIC Supply Voltage Range INPUT Input Offset Voltage Input Offset Voltage Drift Input Bias Current Input Offset Current Input Impedance Input Capacitance Common Mode Rejection Ratio Input Voltage Noise Density OUTPUT Output Current Output Disable Time Output Enable Time TRANSFER CHARACTERISTICS Slew Rate Open Loop Voltage Gain Settling Time ±0.1% Max. ±35 ±38 ±7.5 ±500 ±50 VR+0.8 -65°C to +150°C 300°C -55°C to +125°C -25°C to +85°C 1.2°C/W ABSOLUTE MAXIMUM RATINGS TST TLD TC RTH VCC ±IOUT VIND VCM TJ -Vcc to +Vcc VIN=0V VIN=0V VIN=0V VIN=OV f=DC Differential f=DC Differential (-V CC)-0.1≤ VIN ≤ (+VCC)-3V f=1KHZ IOUT=2.0A IOUT=8.0A Continuous VE/S High- Output Enabled E/S Open or High VE/S Low- Output Disabled E/S Forced Low IE/S High- Output Enabled E/S Indicates High IE/S Low- Output Disabled E/S Indicates Low AV=1 VOUT= 50Vp-p RL=4Ω VOUT=±25V RL=1KΩ AV=-10 50V Step Group A Subgroup 2,3 Typ. ±26 ±26 ±20 ±100 ±27.5 ±26 -50 -55 110 Min. ±26.5 ±25 VR+2.4 100 Min. ±26.5 ±25 VR+2.4 100 Max. ±38 ±10 ±750 ±75 VR+0.8 Typ. ±26 ±20 ±100 ±27.5 ±26 -50 -55 110 Units V mA mA mA mV µV/°C nA nA Ω pF dB nV/√HZ V V A V V µA µA µS µS V/µS dB µS MSK186H/E MSK186 Parameter Test Conditions ELECTRICAL SPECIFICATIONS NOTES: Quiescent Current (Per Amp) ○○○○ Quiescent Current (Per Amp) VIN=0V Overcurrent or TempShutdown Mode VIN=0V Enable/ Shutdown Input Output Voltage Swing ○○○ Unless otherwise specified ±VCC= ±30VDC, VR=0V and E/S Pin is open. All electrical specifications apply to each amplifier. Devices shall be capable of meeting the parameter, but need not to be tested. Typical parameters are for reference only. Industrial grade and 'E' suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ('H' suffix) shall be 100% tested to subgroups 1,2,3 and 4. Subgroup 1,4 T A=TC=+25°C Subgroup 2 TA=TC=+125°C Subgroup 3 TA=TC=-55°C Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle. PRELIMINARY Rev. B 11/06
POWER SUPPLIES: For the MSK 186 maximum total supply voltage is specified as 60V. However, dual and unbalanced power supply operation is permissible as long as total supply voltage does not exceed 60V. POWER SUPPLY BYPASSING: Power supply terminals must be effectively decoupled with a high and low frequency bypass circuit to avoid power supply induced oscillation. An effective decoupling scheme consists of a 0.1µF ceramic capacitor in parallel with a 10µF tantalum capacitor for each power supply pin to ground. In addition, it is recommended that a 0.01µF capacitor be placed between ±Vcc as close to the amplifiers as possible. COMPENSATION: For normal operation output compensation is not typically required. However, if the MSK 186 is intended to be driven into current limit the user may find that an R/C network is required. A snubber network from the output to ground for each ampli- fier will provide stability. If driving large capacitive or inductive loads, a snubber network will also enhance stability. Typically 3Ω to 10Ω in series with 0.01µF is acceptable. CURRENT LIMIT: The MSK 186 offers accurate, user-selectable current limit. Unlike typical designs that use a power resistor in series with the output to sense load, the MSK 186 senses the load indi- rectly and therefore does not require a resistor to handle the full output current. Current limit is selected by controlling the input to the I LIM pin (0 to 633µA). The easiest method is to use a resistor or potentiometer connected between VR and the I LIM pin. Use the following equa- tion to select proper resistor value: 75,000 I LIM A low level control signal (0-633µA) can also be used to con- trol the current level digitally. If the pin is left open, the current is programmed to OA, while connecting I LIM directly to VR sets the output current to it's maximum, typically 10A. The amplifiers are equipped with thermal protection circuitry that protects each amplifier from damage caused by excessive junction temperature. The output is disabled when the junction temperature reaches approximately 160°C. After the junction temperature cools to approximately 140°C, the output is again enabled. The thermal protection may cycle on and off depend- ing on the output load and signal conditions; this may have an undesirable effect on the load. It should be noted that even though this internal protection circuitry does protect against overload conditions, it does not take the place of proper heat sinking. For reliable operation, junction temperature should be limited to 150°C, maximum. TYPICAL CONNECTION DIAGRAM SAFE OPERATING AREA: The safe operating area curve is a graphical representation of the power handling capability of the amplifier under various conditions. Power dissipation of the device is equal to the prod- uct of the voltage across the output transistor times the output current. As can be seen in the curve on page 5, safe operating current decreases with an increase in temperature as well as an increase in the voltage across the output transistor. Therefore, for maximum amplifier performance it is important to keep case temperature as low as possible and to keep ±Vcc as close to the output rail as achievable. THERMAL PROTECTION: For the MSK 186 this pin actually has a dual function. First, when the pin is forced low, the output stage is disabled. Sec- ond, it can be monitored to determine if the device is in thermal shutdown. These functions can be used on the same device with either single or dual supplies. For normal operation, the E/S pin must be left open or pulled at least 2.4 volts above the VR pin. In noisy applications, a small value capacitor between the E/S pin and VR may be required. To disable the output, the user must pull the E/S pin low, no greater than 0.8V above VR. To once again enable the device, the E/S pin must be brought at least 2.4 volts above VR or be disconnected. It should be noted that when the E/S pin is high, the internal thermal shutdown is still active. If the E/S pin is used to monitor thermal shutdown, during normal operation the voltage on the E/S pin is typically 3.5V above VR. Once shutdown has occurred this voltage will drop to approximately 350mV above VR. ENABLE/STATUS PIN: -7.5KΩ RCL= The MSK 186 features a reference (VR) pin to which the ILIM and the E/S pin are referred. VR simply provides a reference point accessible to the user that can be set to V-, ground, or any reference of the user's choice. VR cannot be set below the negative supply or above (V+)-8V. If the minimum V S is used, VR must be set at V-. VR PIN PRELIMINARY Rev. B 11/06
TYPICAL PERFORMANCE CURVES 5 PRELIMINARY Rev. B 11/06
ORDERING INFORMATION
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 qualification status. M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com MECHANICAL SPECIFICATIONS ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. PRELIMINARY Rev. B 11/06
186 H U
S= STRAIGHT; U= BENT UP; D= BENT DOWN SCREENING BLANK= INDUSTRIAL; E=EXTENDED RELIABILITY H=MIL-PRF-38534 CLASS H GENERAL PART NUMBER ESD TRIANGLE INDICATES PIN 1 WEIGHT=25 GRAMS TYPICAL