MSK4324HU MSK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
200 Volt Motor Supply Voltage
10 Amp Output Switch Capability
Shoot-Through/Cross Conduction Protection Hall Sensing and Commutation Circuitry on Board "Real" Four Quadrant Torque Control Capability Good Accuracy Around the Null Torque Point Hermetic Package Design for High Voltage Isolation Plus Good Thermal Transfer 60°/ 120º Phasing Selectable Contact MSK for MIL-PRF-38534 Qualification Status 4707 Dey Road Liverpool, N.Y. 13088 (315) 701-6751 M.S.KENNEDY CORP. 4324
10 AMP, 200V, 3 PHASE
DESCRIPTION: The MSK 4324 is a complete 3 Phase MOSFET Bridge Brushless Motor Control System in a convenient isolated base- plate package. The hybrid is capable of 10 amps of output current and 200 volts of DC bus voltage. It has the normal features for protecting the bridge. Included is all the bridge drive circuitry, hall sensing circuitry, commutation circuitry and all the current sensing and analog circuitry necessary for closed loop current mode (torque) control. When PWM'ing, the transistors are modulated in locked anti-phase (complementary) mode for the tightest control and the most bandwidth. Provisions for applying different compensation schemes are included. The MSK 4324 has good thermal conductivity of the MOSFET's due to a hermetic isolated package design that allows direct heat sinking of the hybrid without insulators. FEATURES: PRELIMINARY Rev. - 2/06 TYPICAL APPLICATIONS
3 Phase Brushless DC Motor Control
+CURRENT COMMAND -CURRENT COMMAND +15 VIN CURRENT MONITOR -15 VIN NC NC ILIMIT ADJUST GND NC NC LGND RTN RTN CVS CVS CØ CØ CV+ BVS BVS BØ BØ BV+ AVS AVS AØ AØ AV+
@ 15mA Load Current Command=0 Volts @ 5mA Load @ 5mA Load Pin 22 1.92KΩ to GND Whole Bridge All Switches off, 100V,150°C @ 5 Amps, 150°C Junction Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ("H" suffix) shall be 100% tested to subgroups 1,2,3 and 4. Subgroups 5 and 6 testing available upon request. Subgroup 1,4 TA=TC=+25°C 2,5 TA=TC=+125°C 3,6 TA=TC=-55°C Measurements do not include offset current at 0V current command. Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. This is to be used for MOSET thermal calculations only. INPUT CURRENT +15 VIN -15 VIN PWM Clock Frequency CLOCK SYNC INPUT VIL VIH Duty Cycle Sync Frequency LOGIC INPUTS (Hall A,B,C,Brake,60°/120°,DIS) VIL VIH REFERENCE ANALOG SECTION Current Command Input Range Current Command Input Current Transconductance Offset Current Current Monitor Current Motor Voltage Swing Error Amp E/A OUT Voltage Swing Slew Rate Gain Bandwidth Product Large Signal Voltage Swing Current Limit Adjust OUTPUT SECTION Voltage Drop Across Bridge (1 Upper & 1 Lower) Leakage Current trr Dead Time Drain-Source On Resistance High Voltage Supply Current Command Input Logic Inputs REFOUT External Load E/A OUT External Load Clock SYNC Input Continuous Output Current Continuous Output Current @ 125°C Case Peak Output Current 200V ±13.5V -0.2V to REFOUT 15 mA 5 mA -0.2V to +15V
10 Amps
5 Amps
15 Amps
0.5°C/W -65°C to +150°C +300°C -40°C to +85°C -55°C to +125°C +150°C RθJC TST TLD TC TJ Parameter Units MSK 4324H/E Test Conditions mA mA mA mA mA mA KHz KHz V V KHz V V V V mA A/V A/V mA V/A V/A V V V/µsec MHz V/mV Amps V V mA nsec µsec Ω Min. Typ. Max. 12.5 Clock+0 3.0 5.82 -13.5 0.90 0.85 -25 0.90 0.85 -12 -12 6.8 175 106 6.25 1.0 1.0 1.0 1.0 6.5 275 220 150 150 150 2.5 Clock+3 0.8 6.57 +13.5 1.5 1.1 1.15 +25 1.1 1.15 +12 +12 TBD TBD 330 0.151 NOTES: MSK 4324 Min. Typ. Max. 12.5 Clock+0 3.0 5.82 -13.5 0.85 -50 0.85 -12 -12 6.8 175 6.25 1.0 1.0 6.5 275 220 150 2.5 Clock+3 0.8 6.57 +13.5 1.5 1.15 +50 1.15 +12 +12 TBD 330 0.151 5,6 5,6 5,6 Group A Subgroup Output PWM'ing Current Command=0 Volts Output PWM'ing Current Command=0 Volts PRELIMINARY Rev. - 2/06 Thermal Resistance (Output Switches@125°C) Storage Temperature Range Lead Temperature Range (10 Seconds) Case Operating Temperature (MSK 4324) (MSK 4324H/E) Junction Temperature
5 Amps @ 125°C TC
AV+, BV+, CV+ - are the power connections from the hy- brid to the bus. The pins for each phase are brought out separately and must be connected together to the V+ source externally. The external wiring to these pins should be sized according to the RMS current required by the motor. These pins should be bypassed by a high quality monolithic ceramic capacitor for high frequencies and enough bulk capacitance for keeping the V+ supply from drooping. Note: this is a power sequence sensitive part. Either turn on all supplies simultaneously or provide ±15V first, then V+ voltages. AØ, BØ & CØ- are the connections to the motor phase wind- ings from the bridge output. The wiring to these pins should be sized according to the current required by the motor. There are no short circuit provisions for these outputs. Shorts to V+ or ground from these pins must be avoided or the bridge will be destroyed. AVS, BVS, CVS - are the return pins on the bottom of each half bridge. They are brought out separately and should be connected together externally to allow the current from each half bridge to flow through the sense resistor. The wiring on these pins should be sized according to the current require- ments of the motor. RTN - is the power return connection from the module to the bus. All ground returns connect to this point from internal to the module in a star fashion. All external ground connections to this point should also be made in a similar fashion. The V+ capacitors should be returned to this pin as close as possible. Wire sizing to this pin connection should be made according to the required current. LGND - is an isolated ground connection to the RTN pin of the hybrid that is connected internally. For any circuitry that needs to be connected to the RTN pin without the influence of current flow through RTN should be connected at this point. GND - is a ground pin that connects to the ground plane for all low powered circuitry inside the hybrid. +15 VIN - is the input for applying +15 volts to run the low power section of the hybrid. This pin should be bypassed with a 10 µF capacitor and a 0.1 µF capacitor as close to this pin as possible. Note: this is a power sequence sensitive part. Either turn on all supplies simultaneously or provide ±15V first, then V+ voltages. -15 VIN - is the input for applying -15 volts to run the low power section of the hybrid. This pin should be bypassed with a 10 µF capacitor and a 0.1 µF capacitor as close to this pin as possible. Note: this is a power sequence sensitive part. Either turn on all supplies simultaneously or provide ±15V first, then V+ voltages. CURRENT COMMAND (+,-) - are differential inputs for con- trolling the module in current mode. Scaled at ±1 amp per volt of input command, the bipolar input allows both forward and reverse current control capability regardless of motor com- mutation direction. The maximum operational command volt- age should be ±10 volts for ±10 amps of motor current. CURRENT MONITOR - is a pin providing a current viewing signal for external monitoring purposes. This is scaled at ±1 amp of motor current per volt output, up to a maximum of ±10 volts, or ±10 amps. As ±10 amps is exceeded, the peaks of the waveform may become clipped as the rails of the amplifiers are reached. This voltage is typically ±12.5 volts, equating to ±12.5 amps of current peaks. E/A OUT - is the current loop error amp output connection. It is brought out for allowing various loop compensation circuits to be connected between this and E/A-. E/A- -is the current loop error amp inverting input connec- tion. It is brought out for allowing various loop compensa- tion circuits to be connected between this and E/A OUT. CLOCK SYNC- is an input for synchronizing to an external clock. The sync circuit will trigger on the edges of the ap- plied clock and effectively shorten the period of the internal oscillator on each cycle. The frequency can be increased from a free running 14 KHz to 20 KHz maximum. The clock applied shall be 15 volts amplitude with at least a 10% duty cycle. REFOUT- is a 6.25 volt regulated output to be used for pow- ering the hall devices in various motors. Up to 15 mA of output current is available. HALL A, B & C - are the hall input pins from the hall devices in the motor. These pins are internally pulled up to 6.25 volts. The halls can reflect a 120/240 degree commutation scheme or a 60/300 degree scheme. BRAKE - is a pin for commanding the output bridge into a motor BRAKE mode. When pulled low, normal operation com- mences. When pulled high, the 3 high side bridge switches turn off and the 3 low side bridge switches turn on, causing rapid deceleration of the motor and will cease motor opera- tion until pulled high again. Logic levels for this input are TTL compatible. It is necessary to toggle ON and OFF BRAKE after power up before normal operation can begin. This is necessary because of the bootstrap high-side power supplies for each phase. These are not continuous high-side supplies and need to be refreshed by turning on the low side switches momentarily with the BRAKE. It is internally pulled high. DIS - is a pin for externally disabling the output bridge. A 15V CMOS logic low will enable the bridge and a 15V CMOS logic high will disable it. After using the DIS pin, the BRAKE must be cycled ON and OFF before normal operation will be- gin. This is due to the bootstrap high-side supplies needing refreshing. 60/120- is a pin fpr selecting the orientation of the commuta- tion sheme of the motor. A high state will produce 60/300 degree commutation, whereas a low state will produce 120/ 240 degree commutation. Logic levels for this input are TTL compatible. It is internally pulled high. ILIMIT ADJUST - is a pin for externally adjusting the current limit point. By placing a resistor to ground from this pin, a voltage divider is created and the current limit will be lowered. Without an external resistor, the current limit is set at 13 Amps. PRELIMINARY Rev. - 2/06
A HALL B HALL C HALL A HALL B HALL C AØ BØ CØ AØ BØ CØ H L L H H L L H L H H L L H H L L H H L H L L H X X X X X X L L L L L L High Level H SOURCE NOTE: Because of the true 4 quadrant method of output switching, Low Level L SINK the output switches will PWM between the ICOMMAND POSITIVE X Don't Care OPEN and ICOMMAND NEGATIVE states, with the average percentage based on ICOMMAND being a positive voltage and a negative voltage. With a zero voltage ICOMMAND, the output switches will modulate with exactly a 50% duty cycle between the ICOMMAND POSITIVE and ICOMMAND NEGATIVE states. APPLICATION NOTES CONTINUED COMMUTATION TRUTH TABLE 60° HALL SENSOR PHASING 120° ICOMMAND = POS. ICOMMAND = NEG. BRAKE CURRENT (A) 2.0 4.0 6.0 8.0 10.0 RESISTOR (KΩ) 0.56 1.37 2.61 4.77 9.48 PRELIMINARY Rev. - 2/06
BUS VOLTAGE FILTER CAPACITORS The size and placement of the capacitors for the DC bus has a direct bearing on the amount of noise filtered and also on the size and duration of the voltage spikes seen by the bridge. What is being created is a series RLC tuned circuit with a resonant frequency that is seen as a damped ringing every time one of the transistors switches. For the resistance, wire resistance, power supply impedance and capacitor ESR all add up for the equivalent lumped resistance in the circuit. The inductance can be figured at about 30 nH per inch from the power supply. Any voltage spikes are on top of the bus voltage and the back EMF from the motor. All this must be taken into account when designing and laying out the system. If everything has been minimized, there is another solution. A second capacitance between 5 and 10 times the first capacitor and it should either have some ESR or a resistor can be added in series with the second capacitor to help damp the voltage spikes. Be careful of the ripple current in all the capacitors. Excessive ripple current, beyond what the capacitors can handle, will destroy the capacitors. REGULATED VOLTAGE FILTER CAPACITORS It is recommended that about 10 µF of capacitance (tantalum) for bypassing the + and -15V regulated outputs be placed as close to the module pins as practical. Adding ceramic bypass capacitors of about 0.1 µF or 1 µF will aid in suppressing noise transients. GENERAL LAYOUT Good PC layout techniques are a must. Ground planes for the analog circuitry must be used and should be tied back to the small pin grounds 9, 14 and 23. Additional ground, pin 26 is an isolated ground that connects internally directly back to the main DC bus ground pin 27, 28. This can be used as necessary for voltage sensing, etc. LOW POWER STARTUP When starting up a system utilizing the MSK 4324 for the first time, there are a few things to keep in mind. First, because of the small size of the module, short circuiting the output phases either to ground or the DC bus will destroy the bridge. The current limiting and control only works for current actually flowing through the bridge. The current sense resistor has to see the current in order for the electronics to control it. If possible, for startup use a lower voltage and lower current power supply to test out connections and the low current stability. With a limited current supply, even if the controller locks up, the dissipation will be limited. By observing the E/A OUT pin which is the error amp output, much can be found out about the health and stability of the system. An even waveform with some rounded triangle wave should be observed. As current goes up, the DC component of the waveform should move up or down. At full current (with a regular supply) the waveform should not exceed +8 volts positive peak, or -8 volts negative peak. Some audible noise will be heard which will be the commutation frequency. If the motor squeals, there is instability and power should be removed immediately unless power dissipation isn't excessive due to limited supply current. For compensation calculations, refer to the block diagram for all information to determine the amplifier gain for loop gain calculations. APPLICATION NOTES CONTINUED PRELIMINARY Rev. - 2/06
PRELIMINARY Rev. - 2/06
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 qualification status. MECHANICAL SPECIFICATIONS THE ABOVE EXAMPLE IS A MILITARY GRADE HYBRID WITH LEADS BENT UP. M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Tel. (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com MSK4324 H U LEAD CONFIGURATION S=STRAIGHT, U=BENT UP, D=BENT DOWN
ORDERING INFORMATION
NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. ESD TRIANGLE INDICATES PIN 1. GENERAL PART NUMBER SCREENING BLANK=INDUSTRIAL; E=EXTENDED RELIABILITY; H=MIL-PRF-38534 CLASS H WEIGHT = 88 GRAMS TYPICAL PRELIMINARY Rev. - 2/06