DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

The MSK 0002RH is a general purpose current amplifier. It is the industry wide RAD tolerant replacement for the LH0002. The device is ideal for use with an operational amplifier in a closed loop configuration to increase current output. The MSK 0002RH is designed with a symmetrical output stage that provides low output impedances to both the positive and negative portions of output pulses. The MSK 0002RH is packaged in a hermetic 8 lead low profile T0-5 header and is specified over the full military temperature range. 4707 Dey Road Liverpool, N.Y. 13088 M.S.KENNEDY CORP. (315) 701-6751 0002RH FEATURES: Radiation Hardened to 100 Krads(Si) (Method 1019.7 Condition A) Radiation Hardened LH0002 Replacement High Input Impedance-180KΩ Min Low Output Impedance-10Ω Max Low Harmonic Distortion DC to 30 MHz Bandwidth Slew Rate is Typically 400 V/μS Operating Range from±5V to ±20V Available to DSCC SMD 5962-78013 Equivalent Non Rad Hard Device MSK 0002 DESCRIPTION: EQUIVALENT SCHEMATIC V2- V1- Input V1+ V2+ Output PIN-OUT INFORMATION High Speed D/A Conversion 30MHz Buffer Line Driver Precision Current Source TYPICAL APPLICATIONS MIL-PRF-38534 AND 38535 CERTIFIED FACILITY RAD HARD, HIGH SPEED, BUFFER AMPLIFIER 8548-2 Rev. D 10/12 CASE=ISOLATED

Case Operating Temperature (MSK 0002K/H RH) (MSK 0002RH) ±20V ±20V 600mW -55°C to +125°C -40°C to +85°C ABSOLUTE MAXIMUM RATINGS TST TLD TJ θjC Storage Temperature Range Lead Temperature Range (10 Seconds) Junction Temperature Thermal Resistance @ TC=125°C Output Devices -65°C to +150°C +300°C +175°C 55°C/W ±VCC VIN Pd Tc Unless otherwise specified ±V CC=±12VDC, RL=1KΩ. Subgroups 5 & 6 shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified for subgroups 5 & 6 for all lots not specifically tested. Devices shall be capable of meeting the parameter, but need not be tested. Subgroup 1,4 T A=TC=+25°C Subgroup 2,5 TA=TC=+125°C Subgroup 3,6 TA=TC=-55°C Refer to SMD 5962-78013 for electrical parameters for devices purchased as such. Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. Pre and post irradiation limits at 25°C, up to 100Krad TID, are identical unless otherwise specified. NOTES: ELECTRICAL SPECIFICATIONS 8548-2 Rev. D 10/12

To determine if a heat sink is necessary for your application and if so, what type, refer to the thermal model and governing equation below. R ΘSA = ((TJ - TA)/PD) - (RΘJC) - (RΘCS) = 125 - 55.15 = 69.9°C/W This heat sink in this example must have a thermal resistance of no more than 69.9°C/W to maintain a junction temperature of no more than +125°C. T J=PD X (RΘJC +RΘCS +RΘSA) +TA Where TJ=Junction Temperature PD=Total Power Dissipation R ΘJC=Junction to Case Thermal Resistance RΘCS=Heat Sink to Ambient Thermal Resistance TC=Case Temperature TA=Ambient Temperature TS=Sink Temperature Thermal Model: Governing Equation: Example: This example demonstrates a worst case analysis for the buffer output stage. This occurs when the output voltage is 1/2 the power supply voltage. Under this condition, maximum power transfer occurs and the output is under maximum stress. Conditions: VCC= ±12VDC Vo= ±6Vp Sine Wave, Freq. = 1KHz RL= 100Ω For a worst case analysis we will treat the ±6Vp sine wave as an 6 VDC output voltage. 1.) Find Driver Power Dissipation PD= (Vcc-Vo) (Vo/R = 360mW 2.) For conservative design, set T J=+125°C Max. 3.) For this example, worst case TA=+80°C 4.) RΘJC = 55° C/W from MSK 0002RH Data Sheet 5.) RΘCS = 0.15° C/W for most thermal greases 6.) Rearrange governing equation to solve for RΘSA Typical Applications: Radiation performance curves for TID testing have been generated for all radiation testing performed by MS Kennedy. These curves show performance trends throughout the TID test process and can be located in the MSK 0002RH radiation test report. The complete radiation test report is available in the RAD HARD PROD- UCTS section on the MSK website. TOTAL DOSE RADIATION TEST PERFORMANCEhttp://www.mskennedy.com/store.asp?pid=9951&catid=19680 8548-2 Rev. D 10/12

TYPICAL PERFORMANCE CURVES 4 8548-2 Rev. D 10/12

ORDERING INFORMATION

The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. MECHANICAL SPECIFICATIONS M.S. Kennedy Corp.

4707 Dey Road, Liverpool, New York 13088

Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com Part Number ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED Industrial MIL-PRF-38534 Class H MIL-PRF-38534 Class K DSCC SMD WEIGHT=1 GRAM TYPICAL 8548-2 Rev. D 10/12