MSD40NBT LSTD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 34
Technical content
A Datasheet MSD40NBT Version 5.2
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
REVISION HISTORY
Version Rev. Date Change Description Approved By 1.0 08/01/11 Initial Release 1.1 08/08/11 Updated I/O information for select pins in the Pin table 1.2 08/26/11 Added PCM Timing information 1.3 10/05/11 Added BT/antenna note, MSD30AG/MSD40NBT Pin Comparison table, MSD40NBT/T-Board image, MSD40NBT schematic 1.4 10/27/11 Added PCM defaults 1.5 12/01/11 General edits including: revisions to PIN table, finalized specifications data, added Integration Consideration section 1.6 12/02/11 Updated the MSD40NBT schematic and current Consumption numbers in the Specifications table; Added series resistors information to the “Integration Considerations” section and added product image 1.7 12/23/11 Added revised mechanical drawing 1.8 01/03/12 Updated Specifications table 1.9 02/08/12 Added pin note and power notes 1.10 02/13/12 Updated mechanical drawing with new side view measurement New product photo and new T-Board photo with Rev. 6 device 1.11 02/16/12 Updated mechanical drawings spacer image and transmit power numbers in the Specs table 2.0 6/29/12 Updated BT Transmit Power 2.1 7/5/12 Updated Receiver Sensitivity values 2.2 7/11/12 Updated notes regarding CMD pull-ups 2.3 8/15/12 Updated Operating Temperature 3.0 10/15/12 Updated format (converted to Laird) and Mounting section with revised spacer information; Added AS/NZS (Australia, New Zealand) certifications; Changed pin name of Pin 12 and updated AS/NZS links 3.1 12/4/12 Made corrections to “Recommended Operating Conditions and DC Electrical Characteristics” table 4.0 1/29/12 Updated Receive Sensitivity Data 4.1 1/30/13 Updated 5GHz frequency and channel data 4.2 17 May 2013 Added BT Priority Important note to the Block Diagram. 4.3 11 July 2013 Fixed ICC certification error (changed IC ID: 6616A-SDCSSD40L to IC ID: 6616A-SDCMSD40NBT) 4.4 20 Sept 2013 Updated Operating and Storage Temperature Dale Chapman 4.5 11 Oct 2013 Removed references to summitdata.com. Sue White 4.6 26 Feb 2014 Added BT SIG certification section Jonathan Kaye 4.7 19 Mar 2014 Added note regarding the following pins: CHIP_PWD_L, SYS_RST_L, BT_RST_L, VDDIO_DR Andrew Chen 4.8 20 Oct 2014 Updated Hardware Schematic. Andrew Chen 4.9 19 Oct 2015 Added Approved By column; updated or removed links Sue White 5.0 12 Aug 2016 Changed Hardware Integration Guide to Datasheet. Sue White 5.1 16 Sept 2016 Added the EU Declaration of Conformity Sue White 5.2 21 Feb 2017 Updated FCC data to 24 non-overlapping channels Jay White
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
CONTENTS
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
1 SCOPE
This document describes key hardware aspects of the SDC-MSD40NBT radio module. This document is intended to assist device manufacturers and related parties with the integration of this radio into their host devices. Data in this document is drawn from a number of sources and includes information found in the Broadcom BCM4329 data sheet issued in June of 2009. Contact Laird or visit the MSD40NBT page of the Laird website for the newest version of this document.
2 OPERATIONAL DESCRIPTION
This device is an SDC-MSD40NBT radio module which supports IEEE 802.11a/b/g/n standards via an SDIO (Secure Digital Input/Output) interface and Bluetooth version 2.1 via a serial UART (Universal Asynchronous Receiver/Transmitter) interface. The radio operates in unlicensed portions of the 2.4 GHz and 5 GHz radio frequency standards using Direct Sequence Spread Spectrum (DSSS) and Orthogonal Frequency Division Multiplexing (OFDM), and supports Bluetooth 2.1 using Frequency Hopping and Bluetooth data rates and automatically adjusts data rates and operational modes based on various environmental factors. When operating on channels in the UNII-2 and UNII-2 Extended bands that are in the 5GHz portion of the frequency spectrum and are subject to Dynamic Frequency Selection requirements, the SDC-MSD40NBT fully conforms to applicable regulatory requirements. In the event that specified types of radar are detected by the network infrastructure, the SDC-MSD40NBT fully conforms to commands from the infrastructure for radar avoidance. The SDC-MSD40NBT interfaces to host devices via a 60-pin connector. The device is based on the Broadcom BCM4329chip which is an integrated device providing a Media Access Controller (MAC), a Physical Layer Controller (PHY or baseband processor), and fully integrated dual-band radio transceiver. To maximize operational range, the SDC-MSD40NBT incorporates a 5 GHz power amplifier (PA) to increase transmit power. The SDC-MSD40NBT has its own RF shielding and does not require shielding provided by the host device into which it is installed in order to maintain compliance with applicable regulatory standards. As such, the device may be tested in a standalone configuration via an extender card. The device buffers all data inputs so that it will comply with all applicable regulations even in the presence of over-modulated input from the host device. Similarly, the SDC-SSD40NBT incorporates power regulation to comply with all applicable regulations even when receiving excess power from the host device. The SDC-MSD40NBTprovides two unique U.FL type antenna connectors to support dual band transmit and receive diversity. Supported host device antenna types include dipole and monopole antennas. Regulatory operational requirements are included with this document and may be incorporated into the operating manual of any device into which the SDC-MSD40NBT is installed. The SDC-MSD40NBT is designed for installation into mobile devices such as vehicle mount data terminals (which typically operate at distances greater than 20 cm from the human body) and portable devices such as handheld data terminals (which typically operate at distances less than 20 cm from the human body). See “Documentation Requirements” for more information.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
3 BLOCK DIAGRAM
Note: Transmitter frequencies for Wi-Fi are 2412-2462 MHz and 5180-5805 MHz. Transmitter frequencies for BT are 2402-2480 MHz. Note: BT functions on the AUX port and not on the Main port. For Wi-Fi and BT single-antenna implementations, the AUX port must be used. IMPORTANT: When BT is transmitting high priority traffic (such as during a scan and/or when sending audio traffic) Wi-Fi receive is sent to the main antenna port (even when set to AUX only). When high priority transmission ends, Wi-Fi receive functionality returns to the AUX port (when set to AUX only). For optimal Wi-Fi performance, we recommend that you populate both the Main and the AUX ports with an antenna.
4 SPECIFICATIONS
Table 1: Specifications Feature Description Physical Interface Molex 54722-0607 60-pin connector (mates to Molex 55560-0607 60-pin connector) Wi-Fi Interface 1-bit or 4-bit Secure Digital I/O Bluetooth Interface Host Controller Interface (HCI) using High Speed UART Antenna Interface 2 Hirose U.FL connectors for dual-band antenna diversity
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Feature Description IMPORTANT: When using a single antenna, it MUST be connected to the Auxiliary (AUX) port. BT functions on the AUX port and not the Main port. For WiFi/BT single-antenna implementations, the AUX port must be used. Main Chip Broadcom BCM4329 Input Voltage Requirements 3.3 VDC ± 10% (core) I/O Signaling Voltage 3.3 VDC ± 10% Average Current Consumption, VDDIO = 3.3 volts (At maximum transmit power setting) Note: Standby refers to the radio operating in PM1 powersave mode. 802.11a (with BT in standby) Transmit: 282 mA (931 mW) Receive: 92 mA (304 mW) Standby: TBD 802.11b (with BT in standby) Transmit: 314 mA (1036 mW) Receive: 92 mA (304 mW) Standby: TBD 802.11g (with BT in standby) Transmit: 288 mA (950 mW) Receive: 92 mA (304 mW) Standby: TBD 802.11n (2.4 GHz) (with BT in standby) Transmit: 292 mA (964 mW) Receive: 92 mA (304 mW) Standby: TBD 802.11n (5 GHz) (with BT in standby) Transmit: 270 mA (891 mW) Receive: 92 mA (304 mW) Standby: TBD Bluetooth (with Wi-Fi in standby) Transmit: TBD mA (TBD mW) Receive: TBD mA (TBD mW) Operating Temperature -30° to 80°C (-22° to 176°F) Operating Humidity 10 to 90% (non-condensing) Storage Temperature -30° to 85°C (-22° to 185°F) Storage Humidity 10 to 90% (non-condensing) Maximum Electrostatic Discharge 8 kV Length 32 mm (1.26 in.) Width 22 mm (0.87 in.) Thickness 5.05mm (0.17 in.) Weight 3.0 g (0.11 oz.) Mounting 60-pin connector, mounting holes (M2 screws)
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Feature Description Wi-Fi Media Direct Sequence-Spread Spectrum (DSSS) Complementary Code Keying (CCK) Orthogonal Frequency Divisional Multiplexing (OFDM) Bluetooth Media Frequency Hopping Spread Spectrum (FSSS) Wi-Fi Media Access Protocol Carrier sense multiple access with collision avoidance (CSMA/CA) Network Architecture Types Infrastructure and ad hoc 802.11n Bluetooth Standards Bluetooth version 2.1 with Enhanced Data Rate Wi-Fi Data Rates Supported 802.11a (OFDM) 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11b (DSSS, CCK) 1, 2, 5.5, 11 Mbps 802.11g (OFDM) 6, 9, 12, 18, 24, 36, 48, 54 Mbps Wi-Fi Modulation BPSK @ 1, 6, 6.5, 7.2 and 9 Mbps QPSK @ 2, 5.5, 11, 12, 13, 14.4,18, 19.5 and 21.7 Mbps 16-QAM @ 24, 26, 28.9, 36, 39 and 43.3 Mbps 64-QAM @ 48, 52, 54, 57.8, 58.5, 65, and 72.2 Mbps 802.11n Spatial Streams 1 (Single Input, Single Output) Supported Bluetooth Data Rates 1, 2, 3 Mbps Bluetooth Modulation GFSK@ 1 Mbps π/4-DQPSK@ 2 Mbps 8-DPSK@ 3 Mbps Supported Regulatory Domains FCC (Americas, Parts of Asia, and Middle East) ETSI (Europe, Middle East, Africa, and Parts of Asia) MIC (Japan) (formerly TELEC) KC (Korea) (formerly KCC) Wi-Fi and Bluetooth 2.4 GHz Frequency Bands ETSI: 2.4 GHz to 2.483 GHz FCC: 2.4 GHz to 2.483 GHz MIC (Japan): 2.4 GHz to 2.495 GHz KC: 2.4 GHz to 2.483 GHz Wi-Fi 2.4 GHz Operating Channels ETSI:13 (3 non-overlapping) FCC:11 (3 non-overlapping) MIC (Japan):14 (4 non-overlapping) KCC:13 (3 non-overlapping)
5 GHz Frequency Bands ETSI
5.15 GHz to 5.35 GHz 5.47 GHz to 5.725 GHz FCC 5.15 GHz to 5.35 GHz 5.47 GHz to 5.725 GHz 5.725 GHz to 5.82 GHz MIC (Japan) 5.15 GHz to 5.35 GHz
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Feature Description KC 5.15 GHz to 5.35 GHz 5.725 GHz to 5.82 GHz
5 GHz Operating Channels ETSI: 19 non-overlapping
FCC: 24 non-overlapping MIC (Japan): 8 non-overlapping KC: 12 non-overlapping Transmit Power Note: Transmit power varies according to individual country regulations. All values nominal, +/-2 dBm. Note: Summit 40 series radios support a single spatial stream and 20 MHz channels only. 802.11a
6 Mbps 16 dBm (40 mW)
54 Mbps 14 dBm (25 mW)
802.11b
1 Mbps 17 dBm (50 mW)
11 Mbps 16 dBm (40 mW)
802.11g
6 Mbps 15 dBm (32 mW)
54 Mbps 13 dBm (20 mW)
802.11n (2.4 GHz)
6.5 Mbps (MCS0) 15 dBm (32 mW)
65 Mbps (MCS7) 11 dBm (13 mW)
802.11n (5 GHz)
6.5 Mbps (MCS0) 16 dBm (40 mW)
65 Mbps (MCS7) 13 dBm (20 mW)
1 Mbps -0.5 dBm (1.1 mW) 2 Mbps -0.5 dBm (1.1 mW) 3 Mbps -0.5 dBm (1.1 mW) Typical Receiver Sensitivity Note: All values nominal, +/-3 dBm. 802.11a:
6 Mbps -90 dBm
24 Mbps -84 dBm
54 Mbps -75 dBm (PER <= 10%)
802.11b:
1 Mbps -96 dBm
11 Mbps -89 dBm (PER <= 10%)
802.11g:
54 Mbps -74 dBm (PER <= 10%)
802.11n (2.4 GHz) MCS0 Mbps -90 dBm MCS4 Mbps -79 dBm MCS7 Mbps -72 dBm 802.11n (5 GHz) MCS0 Mbps MCS4 Mbps -89 dBm -79 dBm MCS7 Mbps -71 dBm
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Feature Description Bluetooth:
1 Mbps TBD
2 Mbps TBD
3 Mbps TBD
Operating Systems Supported Windows Mobile 6.5, 6.1, 6.0, 5.0 Windows Embedded CE 7.0, 6.0, 5.0 Linux, 2.6.x, 3.x.x kernel Security Standards Wireless Equivalent Privacy (WEP) Wi-Fi Protected Access (WPA) IEEE 802.11i (WPA2) Encryption Wireless Equivalent Privacy (WEP, RC4 Algorithm) Temporal Key Integrity Protocol (TKIP, RC4 Algorithm) Advanced Encryption Standard (AES, Rijndael Algorithm) Encryption Key Provisioning Static (40-bit and 128-bit lengths) Pre-Shared (PSK) Dynamic 802.1X Extensible Authentication Protocol Types EAP-FAST EAP-TLS EAP-TTLS PEAP-GTC PEAP-MSCHAPv2 PEAP-TLS LEAP Compliance ETSI Regulatory Domain EN 300 328 (Wi-Fi®) EN 300 328 v1.7.1 (BT 2.1) EN 301 489 EN 301 893 EN 60950-1 EU 2011/65/EU (RoHS) FCC Regulatory Domain FCC 15.247 DTS – 802.11b/g (Wi-Fi) – 2.4 GHz & 5.8 GHz FCC 15.407 UNII – 802.11a (Wi-Fi) – 2.4 GHz & 5.4 GHz FCC 15.247 DSS – BT 2.1 Industry Canada RSS-210 – BT 2.1 MIC (Japan) Regulatory Domain (formerly TELEC) (PENDING) Article 2 Item 19, Category WW (2.4GHz Channels 1-13) Article 2 Item 19-2, Category GZ (2.4GHz Channel 14) Article 2 Item 19-3 Category XW (5150-5250 W52 & 5250-5350 W53) Article 2-1 Item 19-2 (BT 2.1) National Communications Commission LP0002 (100-06-28) – Wi-Fi LP0002 (100-06-28) - Bluetooth
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Feature Description AS/NZS AS/NZS 4268:2008 +A1:2010 (RLAN device) AS/NZS 4268:2008 +A1:2010 (BT device) Certifications Wi-Fi Alliance 802.11a, 802.11b, 802.11g , 802.11n WPA Enterprise WPA2 Enterprise Cisco Compatible Extensions (Version 4) Bluetooth SIG Qualification Warranty Limited Lifetime All specifications are subject to change without notice
5 RECOMMENDED OPERATING CONDITIONS AND DC ELECTRICAL CHARACTERISTICS
Table 2: Recommended Operating Conditions and DC Electrical Characteristics Symbol Parameter Min. Typ. Max. Unit VCC DC Supply Voltage 3.0 3.3 3.6 V VDD_IO DC Supply Voltage (I/O) 1.8 - 3.3 V VIL Low Level Input Voltage (VDDO = 3.3V) - - 0.8 V VIH High Level Input Voltage (VDDO = 3.3V) 2.0 - - V VOL Low Level Output Voltage (100 µA load) - - 0.2 V VOH High Level Output Voltage (-100 µA load) VDDIO– 0.2V - - V IIL Low Current Input - 0.3 - µA IIH High Current Input - 0.3 - µA IOL Low Current Output (VDDO = 3.3V, VOL = 0.4V) - - 3.0 mA IOH High Current Output (VDDO = 3.3V, VOH = 2.9V) - - 3.0 mA CIN Input Capacitance - - 5 pF BT UART Baud Rate 9600 bps 115.2 Kbps (default coming out of reset)
4 Mbps bps/Kbps/Mbps
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.1 SDIO Timing Requirements
The following figure (Figure 1) and table display SDIO default mode timing. Figure 1: SDIO Default Mode Timing Note: Timing is based on CL ≤ 40pF load on CMD and Data. Table 3: SDIO Timing Requirements Symbol Parameter Min. Typ. Max. Unit SDIO CLK (All values are referred to minimum VIH and maximum VIL*) fPP Frequency – Data Transfer mode 0 - 25 MHz fOD Frequency – Identification mode 0 - 400 kHz tWL Clock low time 10 - - ns tWH Clock high time 10 - - ns tTLH Clock rise time - - 10 ns tTHL Clock low time - - 10 ns Inputs: CMD, DAT (referenced to CLK) tISU Input setup time 5 - - ns tIH Input hold time 5 - - ns Outputs: CMD, DAT (referenced to CLK) tODLY Output delay time – Data Transfer mode 0 - 14 ns tODLY Output delay time – Identification mode 0 - 50 ns *min(Vih) = 0.7 x VDDIO and max(ViL) = 0.2 x VDDIO.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.2 UART Timing Requirements
The following figure (Figure 2) displays UART timing. Figure 2: UART Timing Requirements Note: The UART 4-wire interface supports Bluetooth 2.1 HCI Specification. Table 4: UART Timing Requirements Reference Description Min. Typ. Max. Unit
1 Delay time, BT_UART_CTS_N low to
UART_TXD valid - - 24 Baudout cycles
2 Setup time, BT_UART_CTShigh before
- - 10 ns
3 Delay time, midpoint of stop bit to
BT_UART_RTS_N high - - 2 Baudout cycles
5.1.3 PCM Interface Timing
PCM Defaults Long Frame Sync, Master Mode Short Frame Sync, Master Mode Long Frame Sync, Slave Mode Short Frame Sync, Slave Mode
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.4 PCM Defaults
SCO Routing PCM Interface Rate 512 Clock Mode Master Sample Interval 8khz Sync Mode Master 16 bit mono Frame Type Short
5.1.4.1 Short Frame Sync, Master Mode
Figure 3: Short Frame Sync, Master Mode Table 5: Short Frame Sync, Master Mode Reference Description Min. Typ. Max. Unit
1 PCM bit clock frequency 128 - 2048 kHz
2 PCM bit clock high time 128 - - ns
3 PCM bit clock low time 209 - - ns
4 Delay from BT_PCM_CLK rising edge to
BT_PCM_SYNC high - - 50 ns
5 Delay from BT_PCM_CLK rising edge to
BT_PCM_SYNC low - - 50 ns
6 Delay from BT_PCM_CLK rising edge to data
valid on BT_PCM_OUT - - 50 ns
7 Setup time for BT_PCM_IN before BT_PCM_CLK
8 Hold time for BT_PCM_IN after BT_PCM_CLK
9 Delay from falling edge of BT_PCM_CLK during
last bit period to BT_PCM_OUT becoming high impedance - - 50 ns
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.4.2 Short Frame Sync, Slave Mode
Figure 4: Short Frame Sync, Slave Mode Table 6: Short Frame Sync, Slave Mode Reference Description Min. Typ. Max. Unit
2 PCM bit clock high time 209 - - ns
4 Setup time for BT_PCM_SYNC before falling edge of
BT_PCM_BCLK 50 - - ns
5 Hold time for BT_PCM_SYNC after falling edge of
BT_PCM_CLK 10 - - ns
6 Hold time of BT_PCM_OUT after BT_PCM_CLK falling time - - 175 Ns
7 Setup time for BT_PCM_IN before BT_PCM_CLK falling
8 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 - - ns
9 Delay from falling edge of BT_PCM_CLK during last bit
period to BT_PCM_OUT becoming high impedance - - 100 ns
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.4.3 Long Frame Sync, Master Mode
Figure 5: Long Frame Sync, Master Mode Table 7: Long Frame Sync, Master Mode Reference Description Min. Typ. Max. Unit
4 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC
high during first bit time - - 50 ns
5 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC
low during third bit time - - 50 ns Delay from BT_PCM_CLK rising edge to data valid on BT_PCM_OUT - - 50 ns period to BT_PCM_OUT becoming high impedance - - 50 ns
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
5.1.4.4 Long Frame Sync, Slave Mode
Figure 6: Long Frame Sync, Slave Mode Table 8: Long Frame Sync, Slave Mode Reference Description Min. Typ. Max. Unit BT_PCM_CLK during first bit time 50 - - ns Hold time for BT_PCM_SYNC after falling edge of BT_PCM_CLK during second bit period. Note: BT_PCM_SYNC may go low any time from second bit period to last bit period. 10 - - ns Delay from rising edge of BT_PCM_CLK or BT_PCM_SYNC (whichever is later) to data valid for first bit on BT_PCM_OUT - - 50 ns
7 Hold time of BT_PCM_OUT after BT_PCM_CLK falling
8 Setup time for BT_PCM_IN before BT_PCM_CLK falling
9 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 - - ns
Delay from falling edge of BT_PCM_CLK or BT_PCM_SYNC (whichever is later) during last bit in slot to BT_PCM_OUT becoming high impedance - - 100
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
6 PIN DEFINITIONS
Wi-Fi Bluetooth Wi-Fi/Bluetooth Table 9: Pin Definitions Pin Number Pin Name I/O Voltage Reference Description
1 GND - Ground
2 BT_UART_TXD O VDDIO Bluetooth UART Serial Output
3 BT_PRIORITY I/O VDDIO No connect. Not currently supported in the firmware. When not in use, leave open (float). 4 BT_GPIO_6 I/O VDDIO 3.3V I/O Signaling
5 BT_UART_RTS_N O VDDIO Request-to-send signal for the Bluetooth UART interface,
active low. 6 BT_UART_RXD I VDDIO Bluetooth UART Serial Input.
7 BT_HOST_WAKE_B O
Signal from the MSD40NBT to the host indicating that the radio requires attention. Asserted – Host device must wake-up or remain awake. Deasserted – Host device may sleep when sleep criteria are met The signal polarity is software configurable and can be asserted high or low. Note: The default is low but this is only applicable for specific Bluetooth Sleep mode settings. By default, the radio has “No Sleep Mode Set”.
8 RSVD O VDDIO
Reserved for Wake on Wireless Wake on Wireless is not currently supported in the radio firmware. Do not connect when not used
9 RSVD O VDDIO
Reserved. Bluetooth LED Activity Indicator, active high.
10 BT_PCM_OUT O VDDIO PCM data output
11 BT_UART_CTS_N I VDDIO Clear-to-send signal for the Bluetooth UART interface,
active low.
12 BT_WAKE_B I VDDIO
BT Device Wake-up: Signal from the host to the radio indicating that the host requires attention. Asserted – Bluetooth device must wake-up or remain awake Deasserted – Bluetooth device may sleep when sleep criteria are met The signal polarity is software configurable and can be asserted high or low.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Pin Number Pin Name I/O Voltage Reference Description Note: The default is low but this is only applicable for specific Bluetooth Sleep mode settings. By default, the radio has “No Sleep Mode Set”. 13 VCC3_3 - 3.3V Module Power 14 No Connect Not Used. Leave Open (Float) 15 No Connect Not Used. Leave Open (Float) 16 No Connect Not Used. Leave Open (Float) 17 No Connect Not Used. Leave Open (Float) 18 No Connect Not Used. Leave Open (Float) 19 No Connect Not Used. Leave Open (Float)
20 BT_PCM_SYNC I/O VDDIO PCM sync signal
Default master (output); can be configured slave (input) 21 No Connect Not Used. Leave Open (Float)
22 BT_PCM_IN I VDDIO PCM data input
23 No Connect Not Used. Leave Open (Float)
24 BT_PCM_CLK I/O VDDIO
Default master (output): can be configured slave (input) 25 No Connect Not Used. Leave Open (Float)
26 SYS_RST_L I VDDIO
Resets the Wi-Fi radio, active low. Must be asserted when power is first applied to the radio; then released before any transaction can start (see Note 1). See “Electrical Considerations” for the recommended SYS_RST_L circuitry) See Note 2.
27 SDIO_DATA_2
Note: See “Integration Considerations” for additional integration information. 28 RSVD O VDDIO Reserved. No Connect. 29 VCC3_3 - 3.3V Module Power
30 GND - Ground
31 GND - Ground
32 BT_RST_L I VDDIO
Resets the BT radio, active low. Must be asserted when power is first applied to the radio; then released before any transaction can start. See Note 2. 33 No Connect Not Used. Leave Open (Float) 34 No Connect Not Used. Leave Open (Float) 35 No Connect Not Used. Leave Open (Float) 36 RSVD I/O VDDIO Reserved. No Connect. 37 No Connect Not Used. Leave Open (Float) 38 No Connect Not Used. Leave Open (Float)
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Pin Number Pin Name I/O Voltage Reference Description 39 No Connect Not Used. Leave Open (Float) 40 No Connect Not Used. Leave Open (Float) 41 No Connect Not Used. Leave Open (Float) 42 RSVD O VDDIO Reserved. No Connect. 43 No Connect Not Used. Leave Open (Float) 44 No Connect Not Used. Leave Open (Float) 45 No Connect Not Used. Leave Open (Float) 46 No Connect Not Used. Leave Open (Float) 47 No Connect Not Used. Leave Open (Float)
48 CHIP_PWD_L I VDDIO
Powers down both the BT and WLAN radios, active low (see Note 1). See Note 2. 49 No Connect Not Used. Leave Open (Float)
50 RSVD I/O VDDIO Reserved for GPIO
51 No Connect Not Used. Leave Open (Float)
52 RSVD I/O VDDIO Reserved for GPIO
53 RSVD I/O VDDIO Reserved for GPIO
54 RSVD I/O VDDIO Reserved for GPIO
55 SDIO_CMD I/O VDDIO SDIO Command
Note: See “Integration Considerations” for additional integration information.
56 SDIO_CLK I VDDIO SDIO Clock (25MHz
max)
57 SDIO_DATA_0 I/O VDDIO SDIO Data 0
58 SDIO_DATA_3 I/O VDDIO SDIO Data 3
59 SDIO_DATA_1 I/O VDDIO SDIO Data 1
60 GND - Ground
Note 1: Regarding SYS_RST_L and CHIP_PWD_L: Simply releasing SYS_RST_L and CHIP_PWD_L does not guarantee that the BCM4329 chip in the SSD40NBT module comes out of reset. Ensure that both VDD and VDDIO have been applied to the SSD40NBT for at least 110 ms before attempting to initiate SDIO communications. A slightly longer delay is better (safer). Note 2: If the following lines are available on the radio you are integrating into your system, you must connect and control them with the host device. CHIP_PWD_L SYS_RST_L BT_RST_L VDDIO_DR If the radio stays powered up and the host goes down or is reset, communications cannot be re-
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 established with the radio. The host SDIO controller must re-establish communication with the radio by reloading the radio firmware after a power-on or a reset.
6.1.1 Control Signal Timing Diagrams
Figure 7: WLAN = ON, Bluetooth = ON Figure 8: WLAN = OFF, Bluetooth = OFF
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
6.2 MSD30AG and MSD40NBT Pin Comparison Table
Note: Click here for a pin comparison table for the MSD10AG, MSD30AG, and MSD40NBT devices. Pin # MSD30AG MSD40NBT Pin # SSD30AG SSD40NBT Pin Name Pin Name Pin Name Pin Name
1 GND GND 31 GND GND
2 RSVD BT_UART_TXD 32 RSVD BT_RST_L
3 BT_PRIORITY BT_PRIORITY 33 No Connect No Connect
4 BT_FREQ BT_GPIO_6 34 No Connect No Connect
5 RSVD BT_UART_RTS_N 35 No Connect No Connect
6 RSVD BT_UART_RXD 36 BT_ACTIVE BT_ACTIVE
7 RSVD BT_HOST_WAKE_B 37 No Connect No Connect
8 WL_GPIO_1 RSVD 38 No Connect No Connect
9 RSVD RSVD 39 No Connect No Connect
10 RSVD BT_PCM_OUT 40 No Connect No Connect
11 RSVD BT_UART_CTS_N 41 No Connect No Connect
12 RSVD RSVD 42 WL_LED_ACT WL_LED_ACT
13 VCC3_3 VCC3_3 43 No Connect No Connect
14 No Connect No Connect 44 No Connect No Connect
15 No Connect No Connect 45 No Connect No Connect
16 No Connect No Connect 46 No Connect No Connect
17 No Connect No Connect 47 No Connect No Connect
18 No Connect No Connect 48 CHIP_PWD_L CHIP_PWD_L
19 No Connect No Connect 49 No Connect No Connect
20 RSVD BT_PCM_SYNC 50 RSVD RSVD
21 No Connect No Connect 51 No Connect No Connect
22 RSVD BT_PCM_IN 52 RSVD RSVD
23 No Connect No Connect 53 RSVD BT_GPIO_7
24 RSVD BT_PCM_CLK 54 RSVD RSVD
25 No Connect No Connect 55 SDIO_CMD SDIO_CMD
26 SYS_RST_L SYS_RST_L 56 SDIO_CLK SDIO_CLK
27 SDIO_DATA_2 SDIO_DATA_2 57 SDIO_DATA_0 SDIO_DATA_0
28 WLAN_ACTIVE RSVD 58 SDIO_DATA_3 SDIO_DATA_3
29 VCC3_3 VCC3_3 59 SDIO_DATA_1 SDIO_DATA_1
30 GND GND 60 GND GND
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
6.3 Integration Considerations
The following Wi-Fi information should be taken into consideration when integrating the SSD40NBT. Series resistors are recommended in all six SDIO lines (27-56 ohms typically): SDIO_CLK SDIO_CMD SDIO_DATA_0 SDIO_DATA_1 SDIO_DATA_2 SDIO_DATA_3 Note: Although these values may vary with the properties of your host interface and the PCB, they are a reasonable starting point. Note: The series resistors in the SDIO bus provide several design benefits: - If a host controller has too high of a drive strength, then bus ringing may result. Series resistors can reduce this ringing on the I/O lines. - Adding 27-56 ohms of series resistance on the SDIO bus will reduce sharp transitional edges, which may reduce EMI. - Having the series resistors in the PCB layout allows for design flexibility; If they are later found to be unnecessary, zero (0) ohm jumpers may be used in their place
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
7 MECHANICAL SPECIFICATIONS
7.1 Connector Overview
MSD40NBT connector: Molex 54722-0607 60-pin connector Mating connector (on board): Molex 55560-0607 60-pin connector Figure 9: Mechanical Drawing
7.1.1 MSD40NBT Attached to T-Board
Figure 10: MSD40NBT attached to T-board
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
7.2 Mounting
The SDC-MSD40NBT connects to the host via a 60-pin connector. In addition, there are three mounting holes used to secure the device to the host using 2 mm mounting screws. Summit recommends a 1.5 mm metal spacer (bushing) with a conductive mounting screw to connect the exposed ground pads of the radio circuit board to the host ground plane. A 1.5 mm conductive metal spacer with a maximum OD of 4 mm maximizes grounding of the radio and helps to reduce emissions from the radio circuit board. The spacer may also prevent the MSD board from slanting and breaking the connection to the host device when the board is attached to the host. Figure 11: Mounting Recommendations
8 RF LAYOUT DESIGN GUIDELINES
The following is a list of RF layout design guidelines and recommendation when installing a Summit radio into your device. Do not run antenna cables directly above or directly below the radio. Do not place any parts or run any high speed digital lines below the radio. If there are other radios or transmitters located on the device (such as a Bluetooth radio), place the devices as far apart from each other as possible. Ensure that there is the maximum allowable spacing separating the antenna connectors on the Summit radio from the antenna. In addition, do not place antennas directly above or directly below the radio. Summit recommends the use of a double shielded cable for the connection between the radio and the antenna elements. Summit has provided three plated mounting holes that can be used for grounding. When additional ground plane is required, you may use some or all of these grounded mounting holes. Use proper electro-static-discharge (ESD) procedures when installing the Summit radio module.
9 REGULATORY
9.1 Certified Antennas
The SDC-MSD40NBT will be tested to the regulatory standards defined in the “Certifications” section of the Specifications table above. Summit plans to conduct these tests with the following antennas: Cisco AIR-ANT 4941 Form Factor: Whip Type: Dipole
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Maximum 2.4 GHz Gain: 2.2 dBi Tested and Certified 2.4 GHz Transmit Power: TB Ethertronics Form Factor: Isolated Magnetic Dipole™ (IMD) Type: GY Internal Antenna Maximum 2.4 GHz Gain: 2.5 dBi Maximum 5 GHz Gain: 5 dBi Tested and Certified 2.4 GHz Transmit Power: TBD Tested and Certified 5 GHz Transmit Power: TBD Radiall Larson Dipole (R380500314) Form Factor: Whip Type: Dipole Maximum 2.4 GHz Gain: 1.6 dBi (not used during testing) Maximum 5 GHz Gain: 5 dBi Tested and Certified 5 GHz Transmit Power: TBD HUBER+SUHNER (SOA 2459/360/5/0/V_C) Form Factor: Whip Type: Monopole Maximum 2.4 GHz Gain:3dBi Maximum 5 GHz Gain:6.5dBi Tested and Certified 2.4 GHz Transmit Power: TBD Tested and Certified 5 GHz Transmit Power: TBD Note: If the formal test reports for the SDC-MSD40NBTshow that transmit power was decreased to less than 100% on 2.4 GHz edge channels. Summit will make these transmit power reductions in firmware for the edge channels. Integrators do not need to reduce transmit power on a channel-by-channel basis to comply with band edge regulations. Antennas of differing types and higher gains may be integrated as well. If necessary, with the Summit Manufacturing Utility software utility, OEMs may reduce the transmit power of the SDC-MSD40NBT to account for higher antenna gain. In some cases, OEMs may be able to reduce certification efforts by using antennas that are of like type and equal or lesser gain to the above listed antennas.
9.2 Documentation Requirements
In order to maintain regulatory compliance, when integrating the SDC-MSD40NBT into a host device and leveraging Summit’s grants and certifications, it is necessary to meet the documentation requirements set forth by the applicable regulatory agencies. The following sections (FCC, Industry Canada, and European Union) outline the information that may be included in the user’s guide and external labels for the host devices into which the SDC-MSD40NBT is integrated.
9.2.1 FCC
Note: You must place “Contains FCC ID: TWG-SDCMSD40NBT” on the host product in such a location that it can be seen by an operator at the time of purchase.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
9.2.1.1 User’s Guide Requirements
When integrating the SDC-MSD40NBT into a host device, the integrator must include specific information in the user’s guide for the device into which the SDC-MSD40NBT is integrated. The integrator must not provide information to the end user regarding how to install or remove this RF module in the user’s manual of the device into which the SDC-MSD40NBT is integrated. The following FCC statements must be added in their entirety and without modification into a prominent place in the user’s guide for the device into which the SDC-MSD40NBT is integrated: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
9.2.1.2 Labeling Requirements
The final end product must be labeled in a visible area with the following notice: Contains FCC ID: TWG-SDCMSD40NBT
9.2.2 Industry Canada
Note: You must place Contains IC ID: 6616A-SDCMSD40NBT on the host product in such a location that it can be seen by an operator at the time of purchase.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
9.2.2.1 User’s Guide Requirements (for Model # SDC-MSD40NBT)
RF Radiation Hazard Warning To ensure compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 20 cm from all persons. Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter. Installez l'appareil en veillant à conserver une distance d'au moins 20 cm entre les éléments rayonnants et les personnes. Cet avertissement de sécurité est conforme aux limites d'exposition définies par la norme CNR-102 at relative aux fréquences radio. Maximum Antenna Gain – If the integrator configures the device such that the antenna is detectable from the host product. This radio transmitter (IC ID: 6616A-SDCMSD40NBT) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC ID: 6616A-SDCMSD40NBT) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
9.2.3 European Union
9.2.3.1 Declaration of Conformity
Manufacturer: Laird Products: MSD40NBT EU Directives: 1999/5/EC – R&TTE 2006/95/EC – Low Voltage directive (LVD) 2004/108/EC – Electromagnetic compatibility (EMC) 2014/30/EU – EMC Conformity Assessment: Annex IV Reference standards used for presumption of conformity: Article Number Requirement Reference standard(s) 3.1a 2006/95/EC Low voltage equipment safety EN 60950- 1:2006+A11:2009+A1:2010+A12:2011+A2:2013 2006/95/EC RF Exposure EN 62311:2008 3.1b 2004/108/EC Protection requirements with respect to electromagnetic compatibility EN 301 489-1 v1.9.2 (2011-09) EN 301 489-17 v2.2.1 (2012-09) 3.2 1999/5/EC Means of the efficient use of the radio frequency spectrum EN 300 328 v1.9.1 (2015-02) EN 301 893 v1.8.1(2015-03) Declaration: We, Laird, declare under our sole responsibility that the essential radio test suites have been carried out and that the above product to which this declaration relates is in conformity with all the applicable essential requirements of Article 3 of the EU Directive 1999/5/EC, when used for its intended purpose. Place of Issue: Laird W66N220 Commerce Court, Cedarburg, WI 53012 USA tel: +1-262-375-4400 fax: +1-262-364-2649 Date of Issue: August 2016 Name of Authorized Person: Thomas T Smith, Director of EMC Compliance Signature of Authorized Person:
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
9.2.3.2 User’s Guide Requirements
The integrator must include specific information in the user’s guide for the device into which the SDC- MSD40NBT is integrated. In addition to the required FCC and IC statements outlined above, the following R&TTE statements must be added in their entirety and without modification into a prominent place in the user’s guide for the device into which the SDC-MSD40NBT is integrated: This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1:2006+A11:2009+A1:2010Safety of Information Technology Equipment EN 300 328 v1.8.1: (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 300 328 v1.9.1 (BT 2.1) EN 301 489-1 v1.9.1: (2005-09) Electromagnetic compatibility and Radio Spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.2.1 (2002-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment EN 301 893 v1.8.1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); Broadband Radio Access Networks (BRAN); Specific conditions for 5 GHz high performance RLAN equipment EU 2002/95/EC (RoHS) Declaration of Compliance – EU Directive 2003/95/EC; Reduction of Hazardous Substances (RoHS) This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Aršo[name of manufacturer /izgatavotājanosaukums] deklarē, ka[type of equipment / iekārtas tips]atbilstDirektīvas 1999/5/EK būtiskajāmprasībām un citiemar to saistītajiemnoteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal- ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus]megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Menovýrobcu]týmtovyhlasuje, že[typzariadenia]spĺňazákladnépožiadavky a všetkypríslušnéustanoveniaSmernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
9.2.3.3 Labeling Requirements
The final end product must be labeled in a visible area with the following notice:
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
10 BLUETOOTH SIG APPROVALS
10.1 Subsystem Combinations
This application note covers the procedure for generating a new Declaration ID for a Subsystem combination on the Bluetooth SIG website. In the instance of subsystems, a member can combine two or more subsystems to create a complete Bluetooth End Product solution. The following is a sample subsystem listings to use as a reference: Design Name Owner Declaration ID Link to listing on the SIG website MSD40NBT Laird B019705 https://www.bluetooth.org/tpg/QLI_viewQDL.cfm?qid=19705 Windows 8 (Host Subsystem) Microsoft Corporation B012854 https://www.bluetooth.org/tpg/QLI_viewQDL.cfm?qid=12854
10.2 Assumptions
This procedure assumes that the member is simply combining two subsystems to create a new design, without any modification to the existing, qualified subsystems. This is achieved by using the listing interface on the Bluetooth SIG website. Figure 12 shows the basic subsystem combination of a controller and host subsystem. The controller provides the RF/BB/LM and HCI layers, with the host providing L2CAP, SDP, GAP, RFCOMM/SPP and any other specific protocols and profiles existing in the host subsystem listing. The design may also include a profile subsystem. Figure 12: Basic subsystem combination of a controller and host subsystem The Qualification Process requires each company to registered as a member of the Bluetooth SIG – www.bluetooth.org The following link provides a link to the Bluetooth Registration page: https://www.bluetooth.org/login/register/ For each Bluetooth design it is necessary to purchase a Declaration ID. This can be done before starting the new qualification, either through invoicing or credit card payment. The fees for the Declaration ID will depend on your membership status, please refer to the following webpage: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/fees
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 For a detailed procedure of how to obtain a new Declaration ID for your design, please refer to the following SIG document: https://www.bluetooth.org/DocMan/handlers/DownloadDoc.ashx?doc_id=283698&vId=317486 To start the listing, go to: https://www.bluetooth.org/tpg/QLI_SDoc.cfm In step 1, select Reference a Qualified Design and enter the Declaration IDs of each subsystem used in the End Product design. You can then select your pre-paid Declaration ID from the drop down menu or go to the Purchase Declaration ID page, (please note that unless the Declaration ID is pre-paid or purchased with a credit card, it will not be possible to proceed until the SIG invoice is paid. Once all the relevant sections of step 1 are complete, complete steps 2, 3, and 4 as described in the help document. Your new Design will be listed on the SIG website and you can print your Certificate and DoC. For further information please refer to the following training material: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/listing-process-updates
11 ADDITIONAL ASSISTANCE
Please contact your local sales representative or our support team for further assistance: Laird Technologies Connectivity Products Business Unit Support Centre: http://ews-support.lairdtech.com Email: wireless.support@lairdtech.com Phone: Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 Web: http://www.lairdtech.com/wireless
Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless © Copyright 2016 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610
12 APPENDIX A: SCHEMATIC
The following SDC-MSD40NBT schematic may be used as a reference.