DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

www.micropowerdirect.com MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Key Features:  5W & 10W Output Power  200 - 1200 VDC Input Range  4,000 VDC Isolation  Input Under Volt Protection  Output Over Volt Protection  Compact Case  -25°C to +70°C Operation  >300 kHours MTBF MPV10RHI Compact, 6:1 Input PV Power 5 & 10W DC/DC Con vert ers Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 200 600 1,200 VDC Input Start Voltage 185 195 VDC Under Voltage Shutdown 175 185 VDC Input Current MPV05 200 VDC Input 36.0 mA 600 VDC Input 13.0 1200 VDC Input 8.0 MPV10 200 VDC Input 69.0 600 VDC Input 24.0 1200 VDC Input 14.0 Inrush Current 200 VDC Input 4.0 A600 VDC Input 12.0 1200 VDC Input 25.0 Start-Up Time 500 mS Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±1.0 ±2.0 % Line Regulation VIN = MIN to MAX ±0.5 ±1.0 % Load Regulation I OUT = 5% to 100% ±0.5 ±1.0 % Ripple & Noise (20 MHz) See Note 1 50 100 mV P - P Temperature Coeffi cient ±0.02 %/°C Over Power Protection Autorecovery 110 %I OUT Output Short Circuit Continuous (Autorecovery) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 4,000 VDC Isolation Resistance 500 VDC 100 M Switching Frequency 65 kHz EMI Characteristics Parameter Standard Min. Typ. Max. Units Radiated Emissions See Note 2 EN 55022 Class A Conducted Emissions See Note 2 EN 55022 Class A ESD EN 61000-4-2 Criteria B; ±6 kV/±8 RS EN 61000-4-3 Criteria A; 10V/m EFT See Note 3 EN 61000-4-4 Criteria B; ±4 kV Surge See Note 4 EN 61000-4-5 Criteria B; ±1 kV /±2 kV CS EN 61000-4-6 Criteria A; 10 Vrms PFM EN 61000-4-8 Criteria A; 10A/m Voltage Dips EN 61000-4-11 Criteria B; 0% - 70% Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -25 +25 +70 °C Storage Temperature Range -25 +105 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Size See Mechanical Drawings (Page 4) Case Material Aluminum Alloy With Non-Conductive Base (UL94-V0) Weight 6.92 Oz (195g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F , 25°C, Gnd Benign 300 kHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Lead Temperature, See Note 5 Wave Soldering 255 260 265 °CManual Soldering 350 360 370 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. www.micropowerdirect.comwww.micropowerdirect.com MicroPower Direct Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Series

292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com Model Number Input Output Effi ciency (%, Typ) Over Voltage Protection (VDC Typ) Capacitive Load (µF , Max) Fuse Rating Slow-Blow (mA) Voltage (VDC) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range MPV0560S-05RHI 600 200 - 1200 5.0 1,000 0.0 73 7.5 10,000 1,000 MPV1060S-05RHI 600 200 - 1200 5.0 2,000 0.0 75 7.5 6,000 1,000 MPV1060S-24RHI 600 200 - 1200 24.0 420 0.0 82 29.0 1,500 1,000 Derating Curve, MPV1060S-05 Notes: 1. To meet the specifi ed ripple and noise levels, external capacitors are required. see the typical connection information on page three for recommended values. For more information, please contact the factory. 2. All units will meet EN 55022 (CE/RE) class A with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 3. All units will meet EN 61000-4-4 (±4 kV) with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 4. All units will meet the requirements of EN 61000-4-5 (±1 kV/±2 kV), with the input circuit shown in the “Typical Connection 2” diagram on page 3. Contact the factory for more information. 5. Lead temperature is measured 1.5 mm from the case. 6. Operation at no load will not damage the units, however, they may not meet all specifi cations. 7. It is recommended that a fuse be used on the input of a power supply for protection. For the MPV0560-xxRHI & MPV1060-xxRHI series, a 1.0A slow blow should be used. Model Selection Guide Effi ciency vs Output Power (VIN= 600 VDC) Effi ciency vs Input Voltage (Full Load) Derating Curve, MPV0560S-05 & MPV1060S-24

MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com Typical Connection 1 Typical Connection 2: With External EMC Components 5. Recommended values for components are: Model Number External Components NTC MOV C 1, C2, C3, C4 R1, R2, R3, R4 C5 C6 TVS MPV0560S-05RHI 5D-9 SK201000 47 μF/450V 1 M/H9024/2W 1.0 μF/50V 220 μF/25V SMBJ7.0A MPV1060S-05RHI MPV1060S-24RHI 120 μF/35V SMBJ30A For applications that require meeting higher EMC standards, the circuit shown above is recommended. Some notes on this diagram (starting with the input circuit) are: 1. It is recommended that an external fuse be used. The recommended fuse is 1A/250V. 2. The NTC helps to prevent damage to the module in case an input current surge occurs. The recommended value is given in the table below. 3. The MOV helps to prevent damage to the module in case an input voltage surge occurs. The recommended value is given in the table below. 4. Capacitors C 1, C2, C3 and C4 are input fi lter components (connected in series to achieve the required capacitance level). Resistors R1, R2, R3 and R4 help to balance the current across the capacitors. This diagram illustrates a typical board layout for the MPV0560S-xxRHI or MPV1060S-xxRHI with the recom- mended EMI components shown in the “Typical Connection 2” diagram. To meet safety regulations, the board trace widths should be >3 mm, the distance between traces should be >6 mm, and the distance between traces and ground should be >6 mm. Contact the factory for more information. The diagram at left illustrates a typical connection of the MPV0560S-xxRHI or MPV1060S-xxRHI series. Output capacitors C 6 and C5 are fi ltering components. They are required to meet ripple and noise specifi cations. The recommended input components are a fuse, NTC, and MOV. The recommended component values for these are given in the table below. 6. Capacitor C 5 is ceramic. This capacitor is used to fi lter high frequency noise. A recommended value is given in the table below. 7. Capacitor C6 is an electrolytic. A low ESR, high frequency capacitor should be used. The recommended value is given in the table below. 8. The output TVS will help protect system circuitry if power supply fails. A recommended value is given in the table below. 9. Derating on all capacitors should be 80% or more. Typical Board Layout: With External EMC Components

We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com MicroPower Direct offers a two more DC/DC product families with specifi cations that are ideal for use in photovoltaic applications. The MPV1560S and MPV4060S offer a unique combination of compact size, very wide input range, very high isolation and low cost. Features Include: Mechanical Dimensions  15W & 40W Output Power  200 - 1200 VDC Input Range  4,000 VDC Isolation  Under Input Volt Protection  Over Output Volt Protection  Short Circuit Protection  High Effi ciency  Compact Packaging  -25°C to +70°C Operation  High MTBF More Ultra-Wide Input DC/DC Products Pin Function 1+ V IN 2- V IN

3 No Connection

4 No Connection

Notes:

  • All dimensions are typical in inches (mm)
  • Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct also offers DC/DC product families with specifi cations that are ideal for use in railway/transportation applications. Call us today or visit our website for more information.