MPM-10IS MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Parameter Conditions Min. Typ. Max. Units Input Voltage Range 85 265 VAC Input Frequency 47 440 Hz Input Current See Model Selection Guide Inrush Current 115 VAC 10.0 A Pk230 VAC 20.0 EMI Meets CISPR Pub. 22/FCC Class B Output Parameter Conditions Min. Typ. Max. Units Output Voltage See Model Selection Guide Output Current See Model Selection Guide Output Voltage Accuracy ±1.0 ±2.0 % Line Regulation VIN = Min to Max ±0.5 ±1.0 % Load Regulation, Single Output IO = Min to Max ±0.5 ±1.0 % Load Regulation, Dual Output IO = Min to Max ±2.5 ±5.0 % Ripple & Noise (20 MHz) 3.3V & 5.0 VDC Output 1.5 1.8 %VP-P of VO All Other Outputs 0.8 1.0 Hold-Up Time 115 VAC, 60 Hz 20 mSec Temperature Coeffi cient ±0.02 %/°C Over Voltage Protection Zener Diode Clamp 120 % of VO Short Circuit Protection, See Note 3 Continuous (Autorecovery) Overload Protection See Note 4 105 % of INOM General Parameter Conditions Min. Typ. Max. Units Isolation Voltage Input to Output 3,000 VAC Isolation Test Voltage Input to Output, Flash Tested For 60S 4,700 VAC Isolation Resistance 500 VDC 100 M EMI/RFI Conducted EN 55022 Level B EMC Compliance Electrostatic Discharge (ESD) EN 61000-4-2 Level 3 RF Field Susceptibility EN 61000-4-3 Electrical Fast Transients/Bursts On Mains EN 61000-4-4 Level 3 2 kV Surge EN 61000-4-5 Level 3 1kV/2 kV Switching Frequency 100 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -25 +25 +71 °C Storage Temperature Range -40 +85 °C Cooling Free Air Convection (See Derating Curve) Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Plastic & Fiberglass (UL94-V0) Weight 3.23 Oz (92g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F , 25°C, Gnd Benign 300 kHours Safety Standards EN 60950 Safety Class IEC 61140 Class II ECO Design ErP Directive 2009/125/EC Board Mount, 10W Single & Dual Output AC/DC Power Supplies Key Features:
- 10W Output Power
- Universal 85-265 VAC Input
- EN 60950 Approved (UL)
- ErP Directive Compliant
- Meets IEC Safety Class II
- Industry Standard Pin-Out
- Meets EN 55022 B
- >300 kHour MTBF MPM-10IS Series Electrical Specifi cations Specifi cations typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com www.micropowerdirect.com
Notes:
- All dimensions are typical in inches (mm)
- Tolerance x.xx = ±0.01 (±0.25) Pin Single Dual
1 AC-Neutral AC-Neutral
2 AC-Line AC-Line
4 NC Common
NP = No Connection Pin Connections Notes: 1. Load regulation is measured for an output change of 0% to 100% at nominal input line. For multiple output models, the loads are balanced. 2. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 3. Output short circuit protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 4. Output overload protection is provided by a fold back current limiting circuit. 5. The MPM-10IS series includes a built-in 2A/250 VAC fuse. It is recom- mended that an external 1.5A slow blow fuse also be used on the input for protection. Model Number Input Output 1 (Vout 1) Output 2 (Vout 2) Capacitive Load (µF, Max) Effi ciency (%, Typ) Current (A) Voltage (VDC) Current (A) Voltage (VDC) Current (A) 115 VAC 230 VAC Max. Min. Max. Min. Derating Curve Mechanical Dimensions Other output combinations are available Contact the factory for details at: sales@micropowerdirect.com MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com Model Number