MPA150

MPA150 MPD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

Parameter Conditions Min. Typ. Max. Units Input Voltage Range Autoranging 90 132 VAC180 264 Input Frequency 47 63 Hz Input Current, Full Load 110 - 120 VAC 4 A200 - 240 VAC 2 Inrush Current, Cold Start 110 VAC 35 A220 VAC 70 Leakage Current 240 VAC 1.5 mA Power Factor Correction Meets EN61000-3-2 Class A Input Protection T4A/250V Fuse Output Parameter Conditions Min. Typ. Max. Units Output Voltage Adjustment By Trim Pot ±5.0 % Output Regulation (Note 1) ±1.0 % Hold Time 110 VAC, 80% Load 20 mSec Ripple & Noise (20 MHz) (Note 2) See Model Selection Guide Overload Protection Foldback with Autorecovery 110 140 % Over Voltage Protection >130% of Rated Output Voltage. Recycle AC Input. Over Temperature Protection >+85ºC Ambient with Autorecovery Temperature Coeffi cient ±0.04 %/ºC Transient Recovery Time (Note 3) 50% Load Change 2.5 mS Transient Response Deviation 5 % Overshoot/Undershoot At Turn On/Off ±5.0 % Turn On Delay 120 VAC 1 S Output Short Circuit Continuous With Autorecovery General Parameter Conditions Min. Typ. Max. Units Isolation Voltage (Note 4) Input - Output 3,000 VACInput - FG (Frame Ground) 1,500 Primary - Core 1,500 Switching Frequency Fixed 25 kHz Interface Signals Power Supply On Green LED (LED1) on the PCB Power Good Signal PG on CN1. Goes TTL high 100 to 500 mS after regulation. Goes low at least 1 mS before the loss of regulation. Will sink 100 mA. Remote On/Off RMSW on CN1. A TTL low signal inhibits the output. Hiccup Mode Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient 0 +25 +50 ºC Output Derating 2.5%/ ºC from +50 ºC to + 70 ºC Storage Temperature Range -20 +85 ºC Cooling See Model Selection Guide Operating Humidity RH, Non-condensing 90 % Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 30ºC, Gnd Benign 100 kHours Safety Standards UL 60950; CSA C22.2 No. 60950; TUV EN60950; CB Report (IEC 60950) EEMI Compliance Compliance to EN55022 (CISPR22) Class B; EN61000-3-2,3 EMS Immunity Compliance EN6100-4-2,3,4,5,6,8,11; EN55024,; CE Marked (LVD) Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. subject to change without notice Only 5 x 3.2 x 1.5 in!! Key Features:  Compact 1U 150W Supply  PFC to EN61000-3-2 “A”  UL, cUL, TUV Approvals  CE Certifi ed  FCC Class B Emissions  3 - 56 V Output Voltages  Auto Selectable AC Input  600W Peak Power  Four Mechanical Options Compact 1U 150W Single Output Power Factor Corrected AC/DC Power Supplies MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com

Mechanical Dimensions: U-Chassis (U Suffi x) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072  TEL: (781) 344-8226  FAX: (781) 344-8481  E-Mail: sales@micropowerdirect.com Model Number Output Voltage Max. Output Current (Note 5,6,7) Ripple & Noise Effi ciency (Note 7)Factory PreSet Range 16 CFM (U/w Air, F) Convection (U) Min. Notes: 1. Output regulation includes line & load. 2. Ripple & noise is measured from 10 Hz to 20 MHz. Measurement connection to the unit is made with a 0.1 µF ceramic capacitor & a 22 µF electrolytic capacitor con- nected in parallel. 3. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 4. Isolation specifi cations are production HI-Pot tested for 3 seconds. 5. The full output range (see table above) is covered in the safety agency certifi cation. Standard models are factory set to the “Preset” voltage. This may be set to other levels within the range without affecting the agency certifi cation. For more information, contact the factory. 6. Units will provide peak power of 600W for 500 µS. For units capable of longer durations, contact the factory. 7. A 1% minimum load is required to maintain regulation and ripple specifi cations. U-Chassis Cover (C Suffi x) U-Chassis Alternate Cover (B Suffi x)U-Chassis Cover/W Fan (F Suffi x) Input Connector CN3: Mating Molex Part No. 09-91-0500 (5 pin, 3 used) or Howder Terminal Block No. HD-603-3P (3-pin) or equivalent. Output Connector CN2: Mating Molex Part No. 09-91-0600 (6 pin) or Howder Terminal Block No. HD-601-4P (4-pin) or equivalent. Output Pin Assignment: Howder Molex Pins 1 ~ 2: V+ Pins 1 ~ 3: V+ Pins 3 ~ 4: V- Pins 4 ~ 6: V- Logic Signal Connector CN1: Mating JST XHP-3 or equivalent (CHYAO SHIUNN JS-2001-03). Fan driver connector (FAN): 12 VDC / 300 mA is available to drive an external fan. Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02).