MGA-31816_16 AVAGO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 19
Technical content
Features
- Very high linearity at low DC bias power [1]
- High Gain with good gain flatness
- Good Noise Figure
- ROHS compliant
- Halogen free
- Advanced enhancement-mode PHEMT Technology
- QFN 3X3 16-Lead standard package
- Lead-free MSL1 Specifications At 1900 MHz, Vdd = 5 V, Idd = 60 mA (typ) @ 25° C
- OIP3 = 40.2 dBm
- Noise Figure = 1.56 dB
- Gain = 19.4 dB
- P1dB = 20.7 dBm Note: 1. The MGA-31816 has a superior LFOM of 15.8 dB. Linearity Figure of Merit (LFOM) is essentially OIP3 divided by DC bias power. Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 60 V ESD Human Body Model = 300 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control.
Figure 1. Simplified Application Circuit
3 RFin
Table 1. MGA-31816 Absolute Maximum Rating [1] (TA = 25° C)
- Operation of this device in excess of any of
- Source lead temperature is 25° C. Derate 15.2
- Thermal resistance measured using 150° C
Infra-Red Microscopy Technique. Table 2. MGA-31816 Electrical Specification [1] Symbol Parameter and Test Condition Frequency Units Min. Typ. Max.
2600 MHz
3500 MHz
- Measurements obtained from test circuits detailed in Figures 46 and 47 and Table 3.
- OIP3 test condition: F1 – F2 = 1 MHz, with input power of -13 dBm per tone measured at worst case side band.
- LFOM is defined as LFOM = OIP3 (in dBm) – PDC (in dBm). It is a measure of the linearity of an amplifier per unit of DC power consumed.
- Demoboard tuned to best OIP3 with minimum over temperature drift.
Table 4. MGA-31816 Typical Scattering Parameters
Figure 49. K-Factor vs Frequency Table 5. MGA-31816 Typical Noise Parameters
PCB Layout and Stencil Design Notes: 1. All dimensions are in milimeters 2. 4mil stencil thickness recommended PCB LAND PATTERN (TOP VIEW) STENCIL OUTLINE COMBINED PCB & STENCIL LAYOUTS Chamfer 0.24 1.550.23 0.32 0.50 1.55 0.50 ø 0.26 0.56 Chamfer 0.06 1.24 1.24 0.49 0.35 0.21 Chamfer 0.192 0.50 0.32 1.55 1.24 1.24 1.55 0.23 0.21 0.36 0.50 3.20 2.92 0.50 3.20
Part Number Ordering Information Part Number No. of Devices Container MGA-31816-BLKG 100 Antistatic Bag MGA-31816-TR1G 3000 13” Tape/Reel Notes: 1. All dimensions are in milimeters. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold flash and metal burr. TOP VIEW SIDE VIEW BOTTOM VIEW 31816 YYWW XXXX 3.00 ±0.10 3.00 ±0.10 Pin 1 dot By marking 0.20 Ref. 0.00 +0.05 0.40 ±0.05 1.55 ±0.05 Exp.DAP 1.55 ±0.05 Exp.DAP
0.50 Bsc
0.23 ±0.05 1.50 Ref. Pin #1 identi/f_ication Chamfer 0.30 x 45° 0.85 ±0.05
Notes: 1. Measured from centerline of sprocket hole to centerline of pocket 2. Cumulative tolerance of 10 sprocket holes is ±0.20 3. Other material available 4. All dimensions in millimeter unless otherwise stated CL 0.3 ±0.05 3.3 ±0.1 1.55 ±0.1 □1.6 ±0.1 R 0.3 Typical 1.55 ±0.05 2.0 ±0.1[1] 4.0 ±0.1[2] 1.75 ±0.1 5.5 ±0.1[1] 12.0 ±0.3 3.3±0.18.0 ±0.1
For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2015-2016 Avago Technologies. All rights reserved. AV02-3265EN - January 6, 2016 Reel Dimension – 13” Reel 12 mm Width PS 211211 8 7 20 3 PS PS CPN 12MM MPN Detail "X" RECYCLE LOGO SEE DETAIL "X" R19.0±0.5 Ø12.3±0.5(3x) Ø100.0±0.5 Ø329.0±1.0 11.9-15.4** 18.4 MAX.* SLOT 5.0±0.5 (3x) 12.4 +2.0* -0.0 EMBOSSED LETTERING 16.0 mm HEIGHT x MIN. 0.4 mm THICK. EMBOSSED LINE (2x) 89.0 mm LENGTH LINES 147.0 mm AWAY FROM CENTER POINT EMBOSSED LETTERING 7.5 mm HEIGHT DATE CODE ESD LOGO Ø16.0 EMBOSSED LETTERING 7.5 mm HEIGHT HUB Ø100.0±0.5 Ø329.0±1.0 20.2 (MIN.) 1.5 (MIN.) Ø13.0 +0.5 -0.2 BACK VIEW FRONT VIEW 8 7 6 5