MGA-31389_15 AVAGO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 15

Technical content

Features

  • ROHS compliant
  • Halogen free
  • High IP3 at low DC bias power(1)
  • High gain, with good gain flatness
  • Low noise figure
  • Advanced enhancement mode PHEMT Technology
  • Excellent uniformity in product specification
  • SOT-89 standard package Specifications At 0.9 GHz, Vd = 5 V, Id = 73 mA (typ) @ 25° C
  • OIP3 = 38.6 dBm
  • Noise Figure = 2.0 dB
  • Gain = 21.3 dB, Gain flatness (± 50 MHz) = 0.14 dB
  • P1dB = 22.2 dBm
  • IRL = 30.5 dB, ORL = 14.7 dB Note: 1. The MGA-31389 has a superior LFOM of 13.3 dB. Linearity Figure of Merit (LFOM) is essentially OIP3 divided by DC bias power. Simplified Schematic Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 75 V ESD Human Body Model = 1000 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control.

Figure 1. Simplified Schematic diagram

Symbol Parameter Units Absolute Max. Vd, max Drain Voltage, RF output to ground V 5.5 Pd Power Dissipation (2) mW 605 Pin CW RF Input Power dBm 20 Tj Junction Temperature °C 150 TSTG Storage Temperature °C -65 to 150 Thermal Resistance Thermal Resistance (3) (Vd = 5.0 V, Tc = 85° C), θjc = 60.0° C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage. 2. Source lead temperature is 25° C. Derate 16.7 mW/° C for TL>128.0° C. 3. Thermal resistance measured using 150° C Infra-Red Microscopy Technique. TC = 25° C, Vd = 5 V, unless noted Symbol Parameter and Test Condition Frequency Units Min. Typ. Max. Ids Quiescent Current N/A mA 62 73 90 NF Noise Figure 0.45 GHz

0.9 GHz

1.5 GHz

dB – 2.3 2.0 2.0 2.5 Gain Gain 0.45 GHz 21.5 21.3 20.6 OIP3 (2) Output Third Order Intercept Point 0.45 GHz (2)

0.9 GHz (2)

1.5 GHz (2)

dBm 36.3 38.6 38.6 41.3 P1dB Output Power at 1 dB Gain Compression 0.45 GHz dBm 20.6 22.0 22.2 21.7 PAE Power Added Efficiency at P1dB 0.45 GHz % – 41.0 41.2 38.4 IRL Input Return Loss 0.45 GHz dB – 24.3 30.5 15.3 ORL Output Return Loss 0.45 GHz dB – 11.4 14.7 12.1 ISOL Isolation 0.45 GHz dB – 27.2 27.6 28.6 Note : 1. Measurements obtained from a test circuit described in Figure 34 2. OIP3 test condition: F1 - F2 = 10 MHz, with input power of -14 dBm per tone measured at worst case side band.

MGA-31389 Typical Scatter Parameters (1) Tc = 25° C, Vd = 5.0 V, Id = 73 mA, Zo = 50 Ω Freq GHz S11 S11 S11 S21 S21 S21 S12 S12 S12 S22 S22 S22

MGA-31389 K-Factor (1) Tc = 25° C, Vd = 5.0 V, Id = 73 mA, Zo = 50 Ω 0 2 4 6 8 10 12 14 16 18 20 Frequency (GHz) K Factor K Factor MGA-31389 Typical Noise Parameters (1) Tc = 25° C, Vd = 5.0 V, Id = 73 mA, Zo = 50 Ω Freq (GHz) Fmin (dB) Γopt Mag Γopt Ang Rn/Z0 Ga (dB) Note: 1. Measurements are made using 10 mils Rogers RO4350 TRL Board.

Part Number Ordering Information Part Number No. of Devices Container MGA-31389-BLKG 100 7” Tape/Reel MGA-31389-TR1G 3000 13” Tape/Reel Dimensions in mm Dimensions in inches Symbols Minimum Nominal Maximum Minimum Nominal Maximum E 3.94 - 4.25 0.155 - 0.167 MATTE FINISH POLISH POLISH D E L b e e1S C b1 b A OR 1.24 1.23 0.77

0.2 HALF ETCHING

1.625 2.35 DEPTH 0.100 E D E L e e1S OR

NOTES: 1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE ±0.2 2. CAMBER IN COMPLIANCE WITH EIA 481 3. POCKET POSITION RELATIVE TO SPROCKET HOLE MEASURED AS TRUE POSITION OF POCKET, NOT POCKET HOLE 12.0 ± .3 Ao = 4.60 Bo = 4.90 Ko = 1.90 5.50 ± .05 SEE NOTE 3 1.75 ± .10 8.00 Ø 1.5 +0.1/-0.0 2.00 ± .05 SEE NOTE 3

4.00 SEE NOTE 1

Ø 1.50 MIN. Ao Ko R 0.3 TYP . R 0.3 MAX. 0.30 ± .05 A A Bo USER FEED DIRECTION COVER TAPE CARRIER TAPE REEL 13X 13X 13X 13X

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. AV02-2586EN - November 11, 2013 Reel Dimensions – 13” Reel Ø 20.2 M IN 2.0 ± 0.5 Ø 13.0 +0.5 -0.2 102.0 REF 330.0 REF 8.4(MEASURED AT HUB) (MEASURED AT HUB) "A" ATTENTION Electrostatic Sensitive Devices Safe Handling Required MINNEAPOLIS USA U.S PAT 4726534 R LOKREEL R 11.1 MAX. Detail "A" Detail "B" PS PS 1.5

88 REF

96.5 +0.3 - 0.2 Dimensions in mm