MGA-30489 AVAGO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 18

Technical content

Features

  • ROHS compliant
  • Halogen free
  • Very high linearity at low DC bias power[1]
  • Low noise figure
  • High OIP3
  • Advanced enhancement mode PHEMT Technology
  • Excellent uniformity in product specification
  • SOT-89 standard package Specifications At 1.9GHz, Vdd = 5V, Idd = 97mA (typ) @ 25°C
  • OIP3 = 39 dBm
  • Noise Figure = 3 dB
  • Gain = 13.3 dB
  • P1dB = 23.3 dBm
  • IRL = 15dB, ORL = 14.5dB Notes: 1. The MGA-30489 has a superior LFOM of 13dB. Linearity Figure of Merit (LFOM) is essentially OIP3 divided by DC bias power. There are few devices in the market that can match its combination of high linearity and low noise figure at the low DC bias power of 5V/97mA.

Figure 1. Simplified Schematic diagram handling electrostatic sensitive devices. Electrostatic Discharge, Damage and Control.

Thermal Resistance [3] (Vd = 5.0 V) θjc = 50.50°C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage 2. Source lead temperature is 25°C. Derate 19.8mW/°C for TL > 54.56°C 3. Thermal resistance measured using 150°C Infra- Red Microscopy Technique. TC = 25°C, Zo = 50Ω, Vd = 5V, unless noted Symbol Parameter and Test Condition Frequency Units Min. Typ. Max. Ids Quiescent Current N/A mA 80 97 120 NF Noise Figure 0.45GHz 0.9GHz 1.9GHz 2.5GHz dB 2.8 3.5 3.6 Gain Gain 0.45GHz 0.9GHz 1.9GHz 2.5GHz dB 11.8 19.3 16.5 13.3 14.8 OIP3 [5] Output Third Order Intercept Point 0.45GHz(2) 0.9GHz(2) 1.9GHz(2) 2.5GHz(2) dBm 36.5 40.5 40.5 P1dB Output Power at 1dB Gain Compression 0.45GHz 0.9GHz 1.9GHz 2.5GHz dBm 22.5 23.5 23.5 23.3 PAE Power Added Efficiency at P1dB 0.45GHz 0.9GHz 1.9GHz 2.5GHz IRL Input Return Loss 0.45GHz 0.9GHz 1.9GHz 2.5GHz dB 10.5 ORL Output Return Loss 0.45GHz 0.9GHz 1.9GHz 2.5GHz dB 9.5 14.5 ISOL Isolation 0.45GHz 0.9GHz 1.9GHz 2.5GHz dB 25.5 Notes: 4. Measurements obtained from a test circuit described in Figure 43. 5. OIP3 test condition: F1 - F2 = 10MHz, with input power of -10dBm per tone measured at worst case side band. Symbol Parameter Units Absolute Maximum Id,max Drain Current mA 180 Vd,max Devices voltage, RF output to ground V 8.4 Pdiss Power Dissipation [2] mW 1512 Pin, max CW RF Input Power dBm 24 Tj, max Junction Temperature °C 150 Tstg Storage Temperature °C -65 to 150

Application Circuit Description and Layout Figure 43. Circuit diagram Figure 44. Demoboard

Description

For 0.45GHz For 0.9GHz For 1.9GHz For 2.5GHz Value Manufacturer Value Manufacturer Value Manufacturer Value Manufacturer C1 0402 0Ohm NR 0Ohm NR 0Ohm NR 0Ohm NR C2 0402 100pF MURATA 100pF MURATA 100pF MURATA 100pF MURATA C3 0402 NA NR NA NR NA NR NA NR C4 0402 NA NR NA NR NA NR NA NR C5 0402 NA NR NA NR NA NR NA NR C6 0402 100pF MURATA 100pF MURATA 100pF MURATA 100pF MURATA C7 0402 0Ohm NR 0Ohm NR 0Ohm NR 0Ohm NR C8 0402 10pF MURATA 10pF MURATA 10pF MURATA 2.7pF MURATA C9 0402 0.1uF MURATA 0.1uF MURATA 0.1uF MURATA 0.1uF MURATA C10 0603 2.2uF MURATA 2.2uF MURATA 2.2uF MURATA 2.2uF MURATA L1 0402 NA NR NA NR NA NR NA NR L2 0402 NA NR NA NR NA NR NA NR L3 0402 47nH MURATA 47nH MURATA 10nH MURATA 3.0nH MURATA R1 0402 NA NR NA NR NA NR NA NR Note: NR – not required in actual PCB design

Figure 45. Gamma location for Demoboards (which isolates the inband signal from the DC supply). frequency signals from the power supply, C8, C9 and C10. The L3 and C8 also acts as the output tuning circuitry.

MGA-30489 Typical Scatter Parameters Tc = 25°C, Vd = 5.0V, Id = 97mA, Zo = 50Ω Freq GHz S11 S11 S11 S21 S21 S21 S12 S12 S12 S22 S22 S22 K

MGA-30489 Typical Noise Parameters Tc = 25°C, Vd = 5.0V, Id = 97mA, Zo = 50Ω Freq (GHz) Fmin (dB) Γopt Mag Γopt Ang Rn/Zo Ga (dB)

Part Number Ordering Information Part Number No of Devices Container MGA-30489-BLKG 100 Antistatic Bag MGA-30489-TR1G 3000 Tape/reel MATTE FINISH POLISH POLISH D E L b e e1S C b1 b A OR 1.24 1.23 0.77

0.2 HALF ETCHING

1.625 2.35 DEPTH 0.100 E D E L e e1S OR Dimensions in mm Dimensions in inches Symbols Minimum Nominal Maximum Minimum Nominal Maximum E 3.94 - 4.25 0.155 - 0.167

NOTES: 1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE ±0.2 2. CAMBER IN COMPLIANCE WITH EIA 481 3. POCKET POSITION RELATIVE TO SPROCKET HOLE MEASURED AS TRUE POSITION OF POCKET, NOT POCKET HOLE 12.0 ± .3 Ao = 4.60 Bo = 4.90 Ko = 1.90 5.50 ± .05 SEE NOTE 3 1.75 ± .10 8.00 Ø 1.5 +0.1/-0.0 2.00 ± .05 SEE NOTE 3

4.00 SEE NOTE 1

Ø 1.50 MIN. Ao Ko R 0.3 TYP . R 0.3 MAX. 0.30 ± .05 A A Bo USER FEED DIRECTION COVER TAPE CARRIER TAPE REEL 30X 30X 30X 30X

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. AV02-1764EN - May 23, 2013 Reel Dimensions – 13” Reel Ø 20.2 M IN 2.0 ± 0.5 Ø 13.0 +0.5 -0.2 102.0 REF 330.0 REF 8.4(MEASURED AT HUB) (MEASURED AT HUB) "A" ATTENTION Electrostatic Sensitive Devices Safe Handling Required MINNEAPOLIS USA U.S PAT 4726534 R LOKREEL R 11.1 MAX. Detail "A" Detail "B" PS PS 1.5

88 REF

96.5 +0.3 - 0.2 Dimensions in mm