DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Features

/g120/g3Optimum frequency of operation 400 MHz – 1.5 GHz /g120/g3Very low noise figure /g120/g3High gain /g120/g3High linearity performance /g120/g3Excellent isolation /g120/g3GaAs E-pHEMT Technology[1] /g120/g3Low cost small package size: 4.0 x 4.0 x 0.85 mm3 Specifications

900 MHz; Q1: 5 V, 55 mA (typ) Q2: 5 V, 112 mA (typ)

/g120/g30.51 dB Noise Figure /g120/g338 dB Gain /g120/g352 dB RFoutQ1 to RFinQ2 Isolation /g120/g341.4 dBm Output IP3 /g120/g323.3 dBm Output Power at 1dB gain compression

Applications

/g120/g3Low noise amplifier for cellular infrastructure including GSM, CDMA, and W-CDMA. /g120/g3Other very low noise applications. Simplified Schematic Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 90 V ESD Human Body Model = 300 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control. Notes: Enhancement mode technology employs positive gate bias, thereby eliminating the need of negative gate voltage associated with conventional depletion mode devices. C10 C9 R4 8765 103 Q1bias Vdd1 Vdd2 Q1 Q2 RFOUTRFIN AVAGO 13116 YYWW XXXX GND Pin 2 Pin 3 Pin 10 Pin 11 Pin 13 Pin 16 Vbias RFinQ1 RFoutQ2 RFoutQ2 RFinQ2 RFoutQ1 TOP VIEW B OTTOM VIEW All other pics NC – Not Connected

Symbol Parameter Units Absolute Maximum Vdd1 Device Voltage V 5.5 Vdd2 Device Voltage V 5.5 Idd1 Q1 Drain Current mA 90 P d Power Dissipation (2) W 1.02 Pin,max CW RF Input Power dBm 20 Tj,max Junction Temperature °C 150 Tstg Storage Temperature °C -65 to 150 Thermal Resistance [3] (Vdd1 =5.0V, Idd1 =55mA, Vdd2 =5.0V, Idd2 =112mA) /g84jc = 41.9°C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage. 2. Board temperature (T c) is 25° C. For Tc >100° C, derate the device power at 23.9 mW per °C rise in board temperature adjacent to package bottom. 3. Thermal resistance measured using Infrared Measurement Technique. Electrical Specifications [1] RF performance at Vdd1 = 5 V, Vdd2 = 5 V, 900 MHz, TA = 25° C, measured on the demo board. Symbol Parameter and Test Condition Units Min. Typ. Max. Idd1 Current at Q1 mA 42 55 69 Idd2 Current at Q2 mA 92 112 131 NF Noise Figure dB – 0.51 0.85 Gain Gain dB 36.5 38 39.5 OIP3 [2] Output Third Order Intercept Point dBm 37.5 41.4 – OP1dB Output Power at 1 dB Gain Compression dBm 22 23.3 – IRL Input Return Loss, 50 /g58 source dB – -19 – ORL Output Return Loss, 50 /g58 load dB – -12 – |S12| Reverse Isolation dB – 48 – |ISOL 1-2| Isolation between Q1’s Output pin & Q2’s Input pin dB – 52 – Notes: 1. Measurements obtained using demo board described in Figure 7 with component list in Table 1. Input and Output trace loss is not de-embedded from the measurement. 2. OIP3 test condition: f tone1 = 900 MHz, ftone2 = 901 MHz with input power of -29 dBm per tone. 3. Use proper bias, heatsink and derating to ensure maximum channel temperature is not exceeded. See absolute maximum ratings and application note for more details.

Figure 7. Demo Board layout diagram. Figure 8. Demo Board schematic diagram. – Recommended PCB material is 10 mils Rogers R04350. – Suggested component values may vary according to layout and PCB material. Table 1. Component list for 900MHz matching

PCB Land Patterns and Stencil Design PIN #1 IDENTIFICATION CHAMFER 0.30 x 45° 0.40 ±0.10 4.00 ±0.10 0.00 0.10 0.203 Ref. 1.95 Ref.

0.65 Bsc

4.00 ±0.10 Pin 1 Dot By marking 2.70 ±0.10 Exp.DAP 2.70 ±0.10 Exp.DAP 0.85 ±0.10 TOP VIEW SIDE VIEW BOTTOM VIEW AVAGO 13116 YYWW XXXX 0.30 ±0.10 Notes: 1. All dimensions are in milimeters. 2. 4 mil stencil thickness recommended. LAND PATTERN STENCIL OPENING COMBINATION OF LAND PATTERN & STENCIL OPENING 4.00 0.65 2.70 3.96 2.16 4.00 2.70 4.00 3.96 2.70 2.16 3.96 2.16 0.40 0.30 0.65 0.36 0.27 0.65 0.40 0.30 0.36 0.27 2.70 2.16

10° MAX1 0 ° MAX 5.50 ±0.05 1.75 ±0.10 12.0 ±0.30 –0.10 Ø1.50 ±0.25 2.00 ±0.05 4.00 ±0.10 A.K . B. 0.279 ±0.02 Part Number Ordering Information Part Number No. of Devices Container MGA-13116-TR1G 1000 7” Reel MGA-13116-BLKG 100 antistatic bag

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. AV02-2877EN - December 19, 2011 Reel Dimensions (7 inch reel) PS6 PS BACK VIEW Ø178.0±0.5 Ø55.0±0.5 6.25mm EMBOSSED LETTERS LETTERING THICKNESS: 1.6mm SEE DETAIL "X" SLOT HOLE "b" SLOT HOLE(2x) 180° APART. SLOT HOLE "a": 3.0±0.5mm(1x) SLOT HOLE "b": 2.5±0.5mm(1x) Ø13.065° 45° R10.65 45° R5.2 EMBOSSED RIBS RAISED: 0.25mm, WIDTH: 1.25mm 18.0* MAX. Ø51.2±0.3 Ø178.0±0.5 RECYCLE LOGO FRONT VIEW 120 1.5 MIN. Ø20.2 MIN. -0.2 +0.5 DETAIL "X" -0.0 +1.5*12.4 DETAIL "Y"(Slot Hole) 3.5 1.0 SEE DETAIL "Y" FRONT BACK FRONT BACK SLOT HOLE "a" Ø178.0±0.5