DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

www.micropowerdirect.com MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com MG200MRRI4 Medical Approved Compact MiniDIP, 2W DC/DC Con vert ers Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Input Filter Internal Capacitor Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±2.0 ±4.0 % Output Voltage Balance Dual Outputs, Balanced Loads ±0.1 ±1.0 % Line Regulation VIN = Min to Max ±1.2 ±1.5 % Load Regulation, See Note 2 See Model Selection Guide Ripple & Noise (20 MHz) See Note 3 100 150 mV P - P Temperature Coeffi cient ±0.01 ±0.02 %/°C Output Short Circuit 0.5 Sec. Max (Autorecovery) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage, Rated 60 Seconds 4,000 Vrms Reinforced Insulation Working Voltage 300 Vrms Leakage Current 2.0 µA Isolation Resistance 500 VDC 10 G/H9024 Isolation Capacitance 100 kHz, 1V 15 20 pF Switching Frequency 50 80 100 kHz EMI Characteristics Parameter Standard Criteria Level EMC Complies With EN 55011 4TH Edition EMS Complies With EN 60601-1-2 Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -25 +80 °C Case +105 °C Storage Temperature Range -50 +125 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Size See Mechanical Diagram (Page 2) Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.18 Oz (5.1g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F , 25°C, Gnd Benign 2.0 MHours Safety Standards IEC/EN 60601-1, EN 60601-1 3RD Edition, 1xMOPP & 2xMOPP ANSI/AAMI ES 60601-1 1xMOPP & 2xMOPP Recognition (UL Certifi cate) ANSI/AAMI ES 60601-1, CAN/CSA-C22.2 No.60601-1 Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input 9.0 VDC12 VDC Input 18.0 24 VDC Input 30.0 Lead Temperature 1.5 mm From Case For 10 Sec 260 °C Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Key Features:

  • EN 60601 3RD Ed. Approved
  • 2W Output Power
  • 4.0 kVrms Isolation
  • Reinforced Insulation
  • 1 x MOPP & 2 x MOOP per EN 60601-1 3 RD Edition & ANSI/AAMI ES 60601-1
  • 2 µA Leakage Current Max
  • Compact MiniDIP Case
  • Single & Dual Outputs
  • 2.0 MH MTBF

We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.comModel Selection Guide Mechanical Dimensions Mechanical Notes:

  • All dimensions are typical in inch es (mm)
  • Tolerance x.xx = ±0.01 (±0.25) Notes: 1. The specifi ed maximum capacitive load is for each output. 2. Load regulation is measured for a load change of 20% to 100%. 3. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from the +V OUT pin to the -VOUT pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the output ripple. 4. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 5. For dual output units, the maximum capacitive load is given for each output. 6. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0 at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 2.2 µ F is recommended, for 12V input units, a 1.0 µF; and for 24V units a 0.47 µF. 7. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Model Number Input Output Capacitive Load (µF, Max) Load Regulation (%, Max) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual 1 -Vin -Vin 7N C N C

8 NC Common

NC = No Connection Pin Connections Pin NC = No Co Pin Co Derating Curve