MFS2 MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

MODEL: MFS2 MFS2 SPECIFICATIONS ES-1383 Rev.6 Page 1/4 http://www.m-system.co.jp/ Plug-in Signal Conditioners M-UNIT SPLIT-RANGE TRANSMITTER (isolated four outputs) Functions & Features

  • Generates four isolated signals which could control multiple final control elements
  • PC programmable
  • High-density mounting Typical Applications
  • Manipulating multiple valves for split-range control (2.83) (3.15) 139 (5.47) mm (inch) MODEL: MFS2–[1][2]–[3][4]

ORDERING INFORMATION

  • Code number: MFS2-[1][2]-[3][4] Specify a code from below for each of [1] through [4]. (e.g. MFS2-A4-M/Q)
  • Use Ordering Information Sheet (No. ESU-1383)
  • Factory default setting (See “OPERATION DIAGRAM”) will be used if not otherwise specified.
  • Specify the specification for option code /Q (e.g. /C01/S01) [1] INPUT Current A: 4 – 20 mA DC (Input resistance 250 Ω) Voltage 4: 0 – 10 V DC (Input resistance 1 MΩ min.) 6: 1 – 5 V DC (Input resistance 1 MΩ min.) [2] OUTPUT 1 through 4 Current A: 4 – 20 mA DC (Load resistance 500 Ω max.) Voltage 4: 0 – 10 V DC (Load resistance 10 kΩ min.) 6: 1 – 5 V DC (Load resistance 5000 Ω min.) [3] POWER INPUT AC Power M: 85 – 264 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) [4] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating TERMINAL SCREW MATERIAL /S01: Stainless steel

RELATED PRODUCTS

  • PC configurator software (model: MFS2CFG) Software downloadable at M-System’s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable cable types. GENERAL SPECIFICATIONS Construction: Plug-in Connection: M3.5 screw terminals Screw terminal: Chromated steel (standard) or stainless steel Housing material: Flame-resistant resin (black) Isolation: Input to output 1 to output 2 to output 3 to output 4 to power Overrange output: 0 to 100 % Zero adjustment: -5 to +5 % (PC programming) Span adjustment: 95 to 105 % (PC programming) Power LED: Green light turns on in normal operating conditions. Programming: Downloaded from PC; I/O characteristics, high/low limits, fixed output, etc. Configurator connection: 2.5 dia. miniature jack; RS-232-C level Fixed output: Preset fixed outputs provided by contact signal control at the terminals 5 – 6 (Open or Close trigger conditions can be programmed.)

MODEL: MFS2 MFS2 SPECIFICATIONS ES-1383 Rev.6 Page 2/4 http://www.m-system.co.jp/ INPUT SPECIFICATIONS ■ DC Current: Shunt resistor attached to the input terminals (0.5 W) ■ Contact Input Detecting voltage/current: Approx. 2 V DC / 50 μA Detection levels ON resistance: ≤ 200 Ω, ≤ 0.5 V OFF resistance: ≥ 100 kΩ, ≥ 1.7 V INSTALLATION Power consumption

  • AC: approx. 4 VA at 100 V approx. 5.5 VA at 200 V approx. 6.5 VA at 264 V
  • DC: Approx. 2 W Operating temperature: 0 to 50°C (32 to 122°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 400 g (0.88 lb) PERFORMANCE in percentage of span Accuracy: ±0.5 % Temp. coefficient: ±0.05 %/°C (±0.03 %/°F) Response time: ≤ 0.5 sec. (0 – 90 %) Line voltage effect: ±0.5 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @ 1 minute (input to output 1 or output 2 or output 3 or output 4 to power to ground)

500 V AC @ 1 minute (between each output)

MODEL: MFS2 MFS2 SPECIFICATIONS ES-1383 Rev.6 Page 3/4 http://www.m-system.co.jp/ EXTERNAL DIMENSIONS unit: mm (inch) 80 (3.15) (.79) CLAMP (top & bottom) DIN RAIL 35mm wide

  • When mounting, no extra space is needed between units. 80 (3.15) 60 (2.36) 72 (2.83) 7.8 (.31) 2–4.5 (.18) dia. MTG HOLE 25 (.98) deep 14–M3.5 SCREW 12 5614 11 110 15 TERMINAL ASSIGNMENTS unit: mm (inch) 5614 11 110 15 12 (.47) INPUT RESISTOR (model: REM) Input shunt resistor attached for current input. 12 4 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation Base Socket *Input shunt resistor attached for current input. ANALOG INPUT

4 Low Drift

U(+) V(–) POWER CONTACT INPUT CONFIGURATOR JACK

MODEL: MFS2 MFS2 SPECIFICATIONS ES-1383 Rev.6 Page 4/4 http://www.m-system.co.jp/ OPERATION DIAGRAM The diagram below shows an example of I/O characteristics as specified in Table 1. The split-range operations can be specified when ordering, by using Ordering Information Sheet, or programmed by the user using PC Configurator Software. Please refer to Users Manual for the PC Configurator for more information. 1) Two pairs of input and output in % define each split I/O range. Proportional (positive) or inverted (negative) characteristics can be specified. 2) High and low limits for each output can be specified independently within the full-scale range. 3) Fixed output value for each output can be specified independently in advance. These outputs are provided when the contact input is closed or opened (predefined). H limit ≥ Fixed output ≥ Low limit 4) Applying the fixed output or not can be specified independently for each output. In the figure, fixed output is applied to the output 2 with contact input. The solid line shows the function when contact input is shorted. The chain double-dashed line shows the function when contact input is opened. Output 4 H Limit Output 4 Output 3 Output 1 Input % X11 100 X12 X21 X22 X31 X41 X32 X42 Table 1 INPUT % OUTPUT % LIMIT % FIXED OUTPUT % CONTACT INPUT TRIGGER CONDITION Output 1 X 11 = 0.00 Y 11 = 100.00 H 1 = 100.00 Y 1S = 0.00 Not applied ---- X12 = 30.00 Y 12 = 0.00 L 1 = 0.00 Output 2 X 21 = 25.00 Y 21 = 0.00 H 2 = 100.00 Y 2S = 30.00 Applied Open X22 = 50.00 Y 22 = 100.00 L 2 = 0.00 Output 3 X 31 = 55.00 Y 31 = 90.00 H 3 = 90.00 Y 3S = 0.00 Not applied ---- X32 = 80.00 Y 32 = 10.00 L 3 = 10.00 Output 4 X 41 = 70.00 Y 41 = 10.00 H 4 = 70.00 Y 4S = 0.00 Not applied ---- X42 = 100.00 Y 42 = 90.00 L 4 = 10.00 Factory default setting used if no Ordering Information is provided: INPUT % OUTPUT % LIMIT % FIXED OUTPUT % CONTACT INPUT TRIGGER CONDITION Output 1 X 11 = 0.00 Y 11 = 0.00 H 1 = 100.00 Y 1S = 0.00 Not applied Open X12 = 100.00 Y 12 = 100.00 L 1 = 0.00 Output 2 X 21 = 0.00 Y 21 = 0.00 H 2 = 100.00 Y 2S = 0.00 Not applied Open X22 = 100.00 Y 22 = 100.00 L 2 = 0.00 Output 3 X 31 = 0.00 Y 31 = 0.00 H 3 = 100.00 Y 3S = 0.00 Not applied Open X32 = 100.00 Y 32 = 100.00 L 3 = 0.00 Output 4 X 41 = 0.00 Y 41 = 0.00 H 4 = 100.00 Y 4S = 0.00 Not applied Open X42 = 100.00 Y 42 = 100.00 L 4 = 0.00 Output 2 Fixed output (contact input shorted) Output 2 Fixed output (contact input opened) Y12 Y32 Y22 Y42 Output % Y21 Y41 Y2S Y31 Y11 100 Specifications are subject to change without notice.