ME4057

ME4057 MICRONE | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 18

Technical content

V01 www.microne.com.cn Page 1 of 18 1A Lithium Ion Battery Linear Charger ME4057 General Description Features Typical charge cycle（1000mAh battery）

Applications

Typical charge cycle（1000mAh battery）

• Cellular Telephones
• Digital Still Cameras
• MP3 Players
• Bluetooth Applications
• Portable Devices
• USB Bus-Powered Chargers ME4057 is a complete constant-current/constant voltage linear charger for single cell lithium -ion batteries. With a thermally enhanced 8-PIN SOP package on the bottom and low external com ponent count make the ME 4057 ideally suited for portable a pplications. Furthermore the ME4057 is specifically designed to work within USB power specifications. No external sense resistor is needed and no blocking diode is required due to the in ternal PMOSF ET architecture .The rmal feedback regulates the charge current to limit the die temperature during high power operation or high ambient temperature .The charge voltage is fixed at 4.2V,and the charge current can be programmed externally with a single resistor. The ME4057 automatically terminates the charge cycle when the charge current drops to 1/10th the programmed value after the final float voltage is reached. When the input supply (wall adapter or USB supply) is removed the ME 4057 automatically enters a low current state dropping the battery drain current to less than 2μA.The ME4057 can be put into shutdown mode reducing the supply current to 55μA. Other features include Battery temperature monitor, under-voltage lockout, automatic recharge and two status pins to indicate charge and charge termination.
• Protection of battery cell reverse connection
• Programmable charge current up to 1A
• No MOSFET sense resistor o r blocking diode required
• Complete linear Charger in SOP 8 Package for single Cell Lithium-Ion Batteries.
• Constant-Current/Constant-Voltage operation with t hermal regulation to maximize Rate Without risk of overheating.
• Preset 4.2V charge voltage with ±1% accuracy
• Automatic Recharge
• Two Status Indication for Charge status , no battery and battery failure indicators
• C/10 charge termination
• 55μA supply current in shutdown
• 2.9V trickle current charge threshold
• Soft-Start limits inrush current
• Battery Temperature Sensing
• Available in SOP8-PP package

V01 www.microne.com.cn Page 2 of 18 Pin Configuration Pin Assignment Pin Num. Symbol Function

1 TEMP

Connecting TEMP pin to NTC thermistor’s output in Lithium ion battery pa ck. If TEMP pin’s voltage is below 45% or above 80% of supply voltage V CC, this means that battery’s temperature is too low or too high, charging is suspended. The temperature sense function can be disabled by grounding the TEMP pin.

2 PROG

Constant Charge Current Setting and Charge Current Monitor Pin The charge current is programmed by connecting a resistor RPROG from this pin to GND. When in precharge mode, the PROG pin’s voltage is regulated to 0.1V. When charging in constant -current mode this pin ’s vo ltage is regulated to 1V. In all modes during charging, the voltage on this pin can be used to measure the charge current using the following formula:

3 GND Ground

4 VCC

Positive input supply voltage Provides power to the internal c ircuit. When V CC drops to within 80mV of the BAT pin voltage, the ME4057 enters low power sleep mode, dropping IBAT to less than 2μA.

5 BAT

Connect the positive terminal of the battery to this pin. Dropping BAT pin ’s current to less than 2 μA when IC in disable mode or in sleep mode. BAT pin provides charge current to the battery and provides regulation voltage of 4.2V. Charge terminated status output is pulled low by an internal switch to indicate a battery charge terminated; this means Charge termination. Otherwise pin is in high impedance state. Open-Drain charge status output When the battery is being charged, the pin is pulled low by an internal switch, otherwise, pin is in high impedance state. 8 CE Chip enable input A high input will put the device in the normal operating mode. Pulling the CE pin to low level will put the ME4057 into disable mode. The CE pin can be driven by TTL or CMOS logic level.

V01 www.microne.com.cn Page 3 of 18 Block Diagram

V01 www.microne.com.cn Page 4 of 18 Absolute Maximum Ratings Parameter Rating Unit Input supply voltage : VCC -0.3～8 V PROG pin voltage -0.3～VCC+0.3 V BAT pin voltage -0.3～7 V TEMP pin voltage -0.3～10 V pin voltage -0.3～10 V pin voltage -0.3～10 V CE pin voltage -0.3～10 V BAT pin current 1200 mA PROG pin current 1200 μA Maximum junction temperature 145 ℃ Operating ambient temperature :Topa -40～85 ℃ Storage temperature :Tstr -65～125 ℃ Soldering temperature and time +260（Recommended 10S） ℃ Caution: The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions.

V01 www.microne.com.cn Page 5 of 18

Electrical Characteristics

Symbol Parameter Condition Min Typ. Max Unit VCC Input supply voltage ● 4.0 5.0 8.0 V ICC -IBAT static current

• Charge mode, RPROG=1.3K - 150 500 μA
• Standby mode(charge end) - 55 100 μA
• Shutdown mode（RPROG not connected, VCC<VBAT, or VCC<VUV） - 55 100 μA VFLOAL Regulated output voltage 0℃≤TA≤85℃ IBAT=40mA 4.158 4.2 4.242 V IBAT BAT pin current (The condition of current mode is VBAT=3.9V)
• RPROG=2.6K, current mode 450 500 550 mA
• RPROG=1.3K,current mode 950 1000 1050 mA
• Standby mode: VBAT=4.2V 0 -2.5 -6 μA Shutdown mode , RPROG not connected - ±1 ±2 μA Sleep mode, VCC=0V - -1 -2 μA ITRIKL Trickle charge current ●VBAT<VTRIKL, RPROG=1.3K 120 130 140 mA VTRIKL Trickle charge threshold voltage RPROG=1.3K, VBAT rising 2.8 2.9 3.0 V VTRHYS Trickle voltage hysteresis voltage RPROG=1.3K 150 200 250 mV VUV VCC under voltage lockout threshold ● VCC from low to high 3.5 3.7 3.9 V VUVHYS VCC under voltage lockout hysteresis ● 150 200 300 mV VASD VCC-VBAT lockout threshold voltage VCC from low to high 100 140 180 mV VCC from high to low 50 80 110 ITERM C/10 termination current threshold
• RPROG=2.6K 60 70 80 mA
• RPROG=1.3K 120 130 140 VPROG PROG pin voltage ●RPROG=1.3K，current mode 0.9 1.0 1.1 V VCHRG Pin output low voltage =5mA - 0.3 0.6 V VSTDBY Pin output low voltage =5mA - 0.3 0.6 V VTEMP-H The voltage at TEMP increase - 80 83 %VCC VTEMP-L The voltage at TEMP decrease 42 45 - %VCC ΔVRECHRG Recharge battery threshold voltage VFLOAT -VRECHRG 120 180 240 mV TLIM Thermal protection temperature - 145 - ℃ RON The resistance of power FET ”ON” （between VCC and BAT） - 650 - mΩ tSS Soft-start time IBAT=0 to IBAT=1300V/RPROG - 20 - μS tRECHARGE Recharge comparator filter time VBAT from high to low 0.8 1.8 4 mS tTERM Termination comparator filter time IBAT below ICHG/10 0.8 1.8 4 mS IPROG PROG pin pull-up current - 2.0 - μA Note: The ● denotes specifications which apply over the full operating temperature rang, otherwise specifications are at TA=25℃，VCC=5V，unless otherwise specified.

V01 www.microne.com.cn Page 6 of 18 Typical performance characteristics Description of the Principle The ME4057 is a complete constant -current/constant-voltage linear charger for single cell lithium -ion batteries. Constant-current/constant-voltage to charg er batter by internal MOSFET .It can deliver up to 1A of charge current .No blocking diode or external current sense resistor is required. ME 4057 include two Open -Drain charge status Pins: Charge status indicator and battery failure status output The internal thermal regulation circuit reduces the programmed charge current if the die temperature attempts to rise above a preset value of approximately 145℃. This feature protects the ME 4057 from excessive temperature, and allows the user to push the limits of the power handling cap ability of a given circuit board without risk of damaging the ME 4057 or the external components. Another benefit of adopting thermal regulation is that charge current can be set according to typical, not worst-case, ambient temperatures for a given application with the assurance that the charger will automatically reduce the current in worst-case conditions. The charge cycle begins when the voltage at the VCC pin rises above the UVLO level, a current set resistor is connected from the PROG pin to ground, and the CE pin is pulled above the chip enable threshold. The pin outputs a logic low to indicate that the charge cycle is on going. At the beginning of the charge cycle, if the battery voltage is below 2.9V, the charge is in precharge mode to bring the cell voltage up to a safe level for charging. The charger goes into the fast charge constant-current mode once the voltage on the BAT pin rises above 2.9 V. In

V01 www.microne.com.cn Page 7 of 18 constant current mode, the charge current is set by RPROG. When the battery approaches the regulation voltage 4.2V, the charge current begins to decrease as the ME4057 enters the constant-voltage mode. When the current drops to charge termination threshold, the charge cycle is terminated, and pin assumes a high impedance state to indicate that the charge cycle is terminated and pin is pulled low. The charge termination threshold is 10% of the current in constant current mode. To restart the charge cycle, remove the input voltage and reapply it, or momentarily force CE pin to 0V. The charge cycle can also be automatically restarted if the BAT pin voltage falls below the recharge threshold. The on-chip reference voltage, error amplifier and the resistor divider provide regulation voltage with 1% accuracy which can meet the requirement of lithium-ion and lithium polymer batteries. When the input voltage is not present, or input voltage is below VBAT, the charger goes into a sleep mode, dropping battery drain current to less than 3μA. This greatly reduces the current drain on the battery and increases the standby time. The charger can be shutdown by forcing the CE pin to GND. The charging profile is shown in the following figure: Programming charge current The charge current is programmed using a single resistor from the PROG pin to ground. The program resistor and the charge current are calculated using the following equations.: In application, according the charge current to d etermine RPROG ,the relation between R PROG and charge current can reference the following chart:

V01 www.microne.com.cn Page 8 of 18 IBAT (mA) RPROG (K) 0.9 30 50 0.75 70 24 0.8 130 12 0.9 280 5.1 1 650 2 1.3 1000 1 Note: a. K is the coefficient of variation, It generally is 1, but due to the vary operating environment, K is varied in the range: 0.8~1.4 b. The up form is just for reference, it will varied ±10% according to the heat dissipation of the using PCB board; c. The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient. Charge termination A charge cycle is terminated when the charge current falls to 1/10 th the programmed value after the final float voltage is reached. This condition is detected by using an internal filtered comparator to monitor the PROG pin. When the PROG pin voltage falls below 100mV for longer than t TEMP (typically 1.8mS), Charging is terminated. The charge current is latched off and the ME 4057 enters standby mode, where the input supply current drops to 55 μA (Note:C/10 termination is disabled in trickle charging and thermal limiting modes). When charging, transient loads on the BAT pin can cause the PROG pin to fall below 100mV for short periods of time before the DC charge current has dropped to 1/10 th the programmed value. The 1.8mS filter time (t TEMP) on the termination comparator ensures that transient loads of this nature do not result in premature charge cycle termination. Once the average charge current drops below 1/10th the programmed value, the ME4057 terminated the charge cycle and ceases to provide any current through the BAT pin . In this state all loads on the BAT pin must be supplied by the battery. The ME4057 constantly monitors the BAT pin voltage in standby mode. If this vo ltage drops b elow the 4.02V recharge threshold (VRECHRG ),another charge cycle begins and current is once again supplied to the battery. To manually restart a charge cycle when in standby mode, the input voltage must be removed and reapplied or the charger must be shut down and restarted using the PROG pin. Figure 1 shows the state diagram of a typical charge cycle. Charge status indicator ME4057 has two open-drain status indicator output and is pull-down when the ME4057 in a charge cycle. In other status in high impedance . and are all in high impedance when the battery out of the normal temperature. Represent in failure state, when TEMP pin in typical connecting, or the charger with n o battery: red LED and green LED all don’t light. The battery temperature sense function is disabled by connecting TEMP pin to GND. If battery is not connected to charger, pin outputs a PWM level to indicate no battery. If BAT pin connects a 10μF capacitor, the frequency of flicker about 1 -4S, If not use status indicator should set status indicator

V01 www.microne.com.cn Page 9 of 18 output connected to GND. charger’s status Red led Green led Charging light dark Battery in full state dark light Under-voltage, battery’s temperature is to high or too low, or not connect to battery(use TEMP) dark dark BAT pin is connected to 10uF capacitor ，No battery mode (TEMP=GND) Green LED bright, Red LED flicker F=1-4 S Thermal limiting An internal thermal feedback loop reduces the programmed charge current if the die temperature attempts to rise above a preset value of approximately 140℃ . The feature protects the ME4057 from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the ME4057. The charge current can be set according to typical (not worst -case) ambient temperature with the assurance that the charger will automatically reduce the current in worst-case conditions. To prevent the damage caused by the very high or very low temperature done to the battery pack, the ME4057 continuously senses battery pack temperature by measuring the voltage at TEMP pin determined by the voltage divider circuit and the battery’s internal NTC thermistor as shown in Figure 1. The ME4057 compares the voltage at TEMP pin (V TEMP) against its internal V LOW and V HIGH thresholds to determine if charging is allowed. In ME4057, V LOW is fixed at (45% ×Vcc), while V HIGH is fixed at (80%× Vcc). If VTEMP<VLOW or VTEMP>VHIGH , it indicates that the battery temperature is too high or too low and the charge cycle is suspended. When V TEMP is between V LOW and V HIGH, charge cycle resumes . The battery temperature se nse function can be disabled by connecting TEMP pin to GND. Selecting R1 and R2 The values of R1 and R2 in the application circuit can be determined according to the assumed temperature monitor range and thermistor’s values. The Follows is an example: Ass ume temperature monitor range is TL～TH， （ TL＜TH)；the thermistor in battery has negative temperature coefficient（NTC, RTL is thermistor’s resistance at TL， RTH is the resistance at TH，so RTL＞RTH，then at temperature TL, the voltage at TEMP pin is: At temperature TH, the voltage at TEMP pin is: We know VTEMPL＝VHIGH＝K2× Vcc (K2=0.8)；VTEMPH＝VLOW＝K1× Vcc (K1=0.45) Then we can have： For example, NCP03YS110 , operating Temperature is -40℃ to 125℃. If using environment temperature is -25℃ to 125℃, then R TL is the value of the resistance of NCP03YS110 at -25℃, about 66.148Ω; RTH=is the value of the resistance of NCP03YS110 at 125℃, about 1.077Ω.

V01 www.microne.com.cn Page 10 of 18 Likewise, for positive temperature coefficient thermistor in battery, we have RTH＞RTL and we can calculate: We can conclude that temperature monitor range is independent of power supply voltage VCC and it only depends on R1, R2, RTL and RTH: The values of RTH and RTL can be found in related battery handbook or deduced from testing data. In actual application, if only one terminal temperature is concerned (normally protecting overheating), there is no need to use R2 but R1. It becomes very simple to calculate R1 in this case. Under Voltage lockout (UVLO) An internal under voltage lockout circuit monitors the input voltage and keeps the ch arger in shutdown mode until VCC rises above the under voltage lockout threshold . If the UVLO comparator is tripped, the charger will not come out of shutdown mode until VCC rises 140mV above the battery voltage. Manual terminate At any time of the cycle of charging will put the ME 4057 into disable mode to pull CE pin to GND, or remove RPROG （PROG pin is float）. This made the battery drain current to less than 2μA and reducing the supply current to 55μA. To restart the charge cycle, set CE pin in high level or connect a programming resistor. If ME4057 in the under voltage Lockout mode, the and are all in high impedance state, or VCC is above BAT pin 140mV, or VCC is too low. Auto restart Once charge is been terminated, ME 4057 immediately use a 1.8ms filter time（ tRECHARGE ）on the termination comparator to constant monitor the voltage on BAT pin. If this voltage drops below the 4.02V recharge threshold (about between 80% and 90% of V CC), another charge cycle begins. This ensured the battery maintained (or approach) to a charge full status and avoid the requirement of restarting the periodic charging cycle. In the recharge cycle, pin enters a pulled down status.

V01 www.microne.com.cn Page 11 of 18 Fig.1 State diagram of a typical charge cycle Fig.2 Isolating with capacitive load on PROG Pin Stability Considerations In constant -current mode, the PROG pin is in the feedback loop, not the battery. The constant -current mode stability is affected by the impedance at the PROG pin. With no additional capacitance on the PROG pin, the charger is stable with p rogram resistor values as high as 20K Ω. However, additional capacitance on this node reduces the maximum allowed program resistor. Therefore, if I PROG pin is loaded with a capacitance C, the following equation should be used to calculate the maximum resistance value for RPROG： As user, may think charge current is important, not instantaneous current. For example, to run a low current mode switch power which parallel connected with battery, the average current from BAT pin usually importance to instantaneous current. In this case, In order to measure average charge current or isolate capacitive load from IPROG pin, a simple RC filter can be used on PROG pin as shown in Figure 2. In order to ensure the stability add a 10KΩ resistor between PROG pin and filter capacitor. Power dissipation The conditions that cause the ME4057 to reduce charge current through thermal feedback can be approximated by considering the power dissipated in the IC. Nearly all of this power dissip ation is generated by the internal MOSFET-this is calculated to be approximately: PD (VCC VBAT ) X I BAT ME4057

V01 www.microne.com.cn Page 12 of 18 The approximate ambient temperature at which the thermal feedback begins to protect the IC is: For example: The ME 4057 with 5V supply voltage through programmable provides full limiting current 800mA to a charge lithium-ion battery with 3.75V voltage . If JA is 150℃/W ( reference to PCB layout considerations), When ME4057 begins to decrease the charge current, the ambient temperature about: ME4057 can work in the condition of the temperature is above 65 ℃, but the charge current wi ll pull down to below 800mA. In a fixed ambient temperature, the charge current is calculated to be approximately : Just as Description of the Principle part talks about so, the current on PROG pin will reduce in proportion to th e reduced charge current through thermal feedback. In ME 4057 design applications don’t need to considerate the worst case of thermal condition, this point is importance, because if the junction temperature up to 145℃ ,IC will auto reduce the power dissipation. Thermal considerations Because of the small size of the thin SOP8 package, it is important to use a good thermal PC board layout to maximize the available charge current. The thermal path for the heat genera ted by the IC is from the die to the copper lead frame, through the package leads, (especially the ground lead) to the PC board copper. The PC board copper is the heat sink. The footprint copper pads should be as wide as possible and expand out to larger c opper areas to spread and dissipate the heat to the surrounding ambient. Other heat sources on the board, not related to the charger, must also be considered when designing a PC board layout because they will affect overall temperature rise and the maximum charge current. Add thermal regulation current It will effective to decrease the power dissipation through reduce the voltage of both ends of the inner MOSFET. In the thermal regulation, this action of transporting current to battery will raise. One of the measure is through an external component(as a resistor or diode) to consume some power dissipation. For example: The ME4057 with 5V supply voltage through programmable provides full limiting current 800mA to a charge lithium-ion battery with 3.75V vol tage. If JA is 125℃/W, so that at 25℃ ambient temperature, the charge current is calculated to be approximately : In order to increase the thermal regulation charge current, can decrease the power dissipation of the IC through reducing the voltage (as show fig.3) of both two ends of the resistor which connecting in series with a 5V AC adapter. With square equation to calculate IBAT ： If R CC=0.25Ω, V S=5V, VBAT=3.75V, TA=25℃ and JA =125℃/W, we can calculate the thermal regulation charge current: IBAT＝948mA. It means that in this structure it can output 800mA full limiting charge current at more high ambient temperature environment. Although it can transport more energy and reduce the charge time in this application, but actually spread charge

V01 www.microne.com.cn Page 13 of 18 time, if ME 4057 stay in under-voltage state, when V CC becomes too low in voltage mode. Fig.4 shows how the voltage reduced with increase R CC value in this circuit. This technique will act the best function when in order to maintain the minimize the dimension of the components and avoid voltage decreased to minimize RCC . VCC bypass capacitor Many types of capacitors can be used for input bypassing, however, caution must be exercised when using multilayer ceramic capacitors. Because of the self -resonant and high Q characteristics of some types of ceramic capacitors, high voltage transients can be generated under some start-up conditions, such as connecting the charger input to a live power source. Adding a 1.5Ω resistor in series with a ceramic capacitor will minimize start-up voltage transients. Charging Current Soft Start ME4057 includes a soft start circuit which used to maximize to reduce the surge current in the begging of charge cycle. When restart a new charge cycle, the charging current ramps up from 0 to the full charging current within 20μs. In the start process it can maximize to reduce the action which caused by surge current load. USB and Wall Adapter Power ME4057 allows charging from a USB port, a wall adapter can also be used to charge Li -Ion/Li-polymer batteries. Figure 5 shows an example of how to combine wall adapter and USB power inputs. A P -channel MOSFET, M1, is used to prevent back conducting into the USB port when a wall adapter is present and Schottky diode, D1, is used to prevent USB power loss through the 1KΩ pull-down resistor. Generally, AC adaptor is able to provide bigger much current than the value of specific current limiting which is 500mA for USB port. So can rise charge current to 600mA with using a N -MOSFET (MN1) and an additional set resistor value as high as 10KΩ. Fig.3:A circuit to maximum the thermal regulation charge current Fig.4:The r elationship curve between charge current with RCC ME4057

V01 www.microne.com.cn Page 14 of 18 Fig.5:Combining Wall Adapter and USB Power Typical Application Mainly used in Cellular telephones, MP3, MP4 players, digital still cameras, electronic dictionary, GPS, portable devices and vary chargers. 1. Suitable for the function of battery ’s temperature detection, the application of the indicator of battery ’s temperature anomaly and charge status. 2. Suitable for the application of USB power and the charge of wall adapter ME4057

V01 www.microne.com.cn Page 15 of 18 5. Add a resistor for power dissipation, Red LED for charge status, green LED for charge terminate state 3. Suitable for charge status indicator, which the application not need battery ’s temperature detection. 4. Suitable for the application which not need charge status indicator and battery’s temperature detection. ME4057 ME4057

V01 www.microne.com.cn Page 16 of 18 Board Layout Considerations

• RPROG at PROG pin should be as close to ME4057 as possible, also the parasitic capacitance at PROG pin should be kept as small as possible.
• The capacitance at VCC pin and BAT pin should be as close to ME4057 as possible.
• During charging, ME4057’s temperature may be high, the NTC thermistor should be placed far enough to ME4057 so that the thermistor can reflect the battery’s temperature correctly.
• It is very important to use a good thermal PC board layout to maximize charging current. The thermal path for the heat generated by the IC is from the die to the copper lead frame through the package lead (especially the ground lead) to the PC board copper, the PC board copper is the heat sink. The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient. Feed through vias to inner or backside copper layers are also useful in improving the overall thermal performance of the charger. Other heat sources on the board, not related to the charger, must also be considered when designing a PC board layout because they will affect overall temperature rise and the maximum charge current.
• The ability to deliver maximum charge current under all conditions require that the exposed metal pad on the back side of the ME4057 package be soldered to the PC board ground. Failure to make the thermal contact between the exposed pad on the backside of the package and the copper board will result in larger thermal resistance.

V01 www.microne.com.cn Page 17 of 18 Packaging Information: Packaging Type: SOP8-PP Character Dimension (mm) Dimension (Inches) Min Max Min Max A 1.350 1.750 0.053 0.069 A1 0.1 0.3 0.004 0.012 B 1.27(Typ.) 0.05(Typ.) b 0.330 0.510 0.013 0.020 c 0.9(Typ.) 0.035(Typ.) c1 1.0(Typ.) 0.039(Typ.) D 5.8 6.2 0.228 0.244 D1 3.202 3.402 0.126 0.134 E 3.800 4.000 0.150 0.157 E1 2.313 2.513 0.091 0.099 F 4.7 5.1 0.185 0.201 L 0.675 0.725 0.027 0.029 G 0.32(Typ.) 0.013(Typ.) R 0.15(Typ.) 0.006(Typ.) 1 7° 7°  8° 8°

V01 www.microne.com.cn Page 18 of 18  The information described herein is subject to change without notice.  Nanjing Micro One Electronics Inc is not responsible for any problems caused by circuits or diagrams described herein whose related ind ustrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design.  Use of the information described herein for other purposes and/or repr oduction or copying without the express permission of Nanjing Micro One Electronics Inc is strictly prohibited.  The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Nanjing Micro One Electronics Inc.  Although Nanjing Micro One Electronics Inc exe rts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.