MCX18LG0A SONY | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 23

Technical content

Features

  • Ultra-small size: MCX18LG0A: 18.3mm
  • 18.3mm · 8.4mm MCX18LG0B: 18.3mm · 18.3mm · 9.6mm
  • Y, U/V 16-bit digital output
  • 180,000-pixel color CCD image sensor
  • Equipped with a fixed focus lens: MCX18LG0A: F2.8 f = 2.9mm MCX18LG0B: F2.8 f = 4.0mm

Applications

  • TV conference cameras
  • Image input cameras Absolute Maximum Ratings
  • Supply voltage V H +18 V DV DD 1, DVDD 2 +7.0 V AV DD 1, AVDD 2, AVDD 3 +7.0 V AV DD 4 +7.0 V VCC +14.0 V VL –17.5 V
  • Input voltage V I –0.5 to DVDD + 0.5 V
  • Operating temperature Topr 0 to +40 °C
  • Storage temperature Tstg –30 to +80 °C Recommended Operating Conditions
  • Supply voltage V H 14.25 to 15.75 V DV DD 1, DVDD 2 3.0 to 3.6 V AV DD 1, AVDD 2, AVDD 3 4.75 to 5.25 V AV DD 4 4.7 to 5.5 V VCC 4.5 to 5.25 V VL –8.5 to –7.5 V
  • Input voltage V DCIN 1.0 to 4.5 V
  • Operating temperature Topr 0 to +40 °C Block Diagram Peripheral ICs
  • EVR: MB88347 (Fujitsu Limited.)
  • EEPROM: AK6420 (Asahi Kasei Microsystems Co., Ltd.) – 1 – MCX18LG0A/MCX18LG0B E97541-PS Micro Unit CCD Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. 64 pin QFN (Ceramic) Lens Y, U/V CCD Image Sensor S/H, AGC Digital Signal Process Timing Generator

– 2 – MCX18LG0A/MCX18LG0B Pin Configuration 41424344454647484950515253545556 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SIFSEL AGND VH AGND AV DD4 V CC AGND SUBIN AGCCONT OFFSET AV DD1 AV DD2 AV DD3 DCIN DCOUT SUBOUT DGND DGND CO7 CO6 CO5 CO4 CO3 CO2 CO1 CO0 NRB HD VD TEST XCLR SCK SI SO C ASI C SR O M R ESETTG D G N D O SC I O SC O C K D VD D 1 XC S C ASC K C ASO C SEVR D G N D VL D G N D D C K YO 7 YO 6 YO 5 YO 4 YO 3 YO 2 YO 1 YO 0 D VD D 2 SH O U T SH IN AG N D C C D O U T AG N D

– 3 – MCX18LG0A/MCX18LG0B Pin Description Pin No. Symbol I/O Description YO1 YO0 DV DD 2 SHOUT SHIN AGND CCDOUT AGND SIFSEL AGND VH AGND AV DD 4 VCC AGND SUBIN AGCCONT OFFSET AV DD 1 AV DD 2 AV DD 3 DCIN DCOUT SUBOUT VL DGND CSEVR CASO CASCK XCS DV DD 1 CK OSCO OSCI DGND O O O I O I I I I I O O O O O I I O I Luminance signal output. Luminance signal output. +3.3V power supply for signal processing system. Sample-and-hold output. Connect directly to Pin 5. Sample-and-hold input. Analog GND CCD image sensor buffer output. Analog GND Serial communication mode selection: Microcomputer (low) /RS232C (high). Analog GND +15V power supply for CCD image sensor drive. Analog GND +5V power supply for A/D converter. +5V power supply for sample-and-hold. Analog GND CCD image sensor SUB voltage input. AGC control. OFFSET control. +5V power supply for sample-and-hold pulse. +5V power supply for RG pulse. +5V power supply for H pulse. DC amplifier input. DC amplifier output. SUB pulse output. –8V power supply for CCD image sensor drive. Digital GND EVR chip select. Serial communication data output for peripheral ICs (EVR, EEPROM). Serial communication clock output for peripheral ICs (EVR, EEPROM). Switched by the SIFSEL setting. Chip select during microcomputer mode. Baud rate setting (4800bps (low)/9600bps (high)) during RS232C mode. +3.3V power supply for timing generator. 27MHz clock input. 27MHz oscillator output. 27MHz oscillator input. Digital GND

– 4 – MCX18LG0A/MCX18LG0B Pin No. Symbol I/O Description RESETTG CSROM CASI SO SI SCK XCLR TEST VD HD NRB CO0 CO1 CO2 CO3 CO4 CO5 CO6 CO7 DGND DGND DGND DCK YO7 YO6 YO5 YO4 YO3 YO2 I O I O I I I I O O O O O O O O O O O O O O O O O O Reset pin (active low) with pull-up resistor for timing generator. EEPROM chip select. Serial communication data input for peripheral ICs (EVR, EEPROM). Serial communication data output. Serial communication data input. Serial communication clock input. Initialization pin (active low). EEPROM re-read. Test pin. Leave this pin open. Vertical sync signal output. Horizontal sync signal output. Color identification signal output. Chroma signal output. Chroma signal output. Chroma signal output. Chroma signal output. Chroma signal output. Chroma signal output. System setting pin during power on. (Connect pull-down resistor.) Chroma signal output. System setting pin during power on. (Connect pull-down resistor.) Chroma signal output. System setting pin during power on. (Connect pull-down resistor.) Digital GND Digital GND Digital GND Clock output pin for digital output. Luminance signal output. Luminance signal output. Luminance signal output. Luminance signal output. Luminance signal output. Luminance signal output.

– 5 – MCX18LG0A/MCX18LG0B Item

Electrical Characteristics

Symbol UnitMin. Typ. Max.Pins Conditions Input voltage 1 Input voltage 2 Input voltage 3 Input voltage 4 Output voltage Output voltage Output voltage Output voltage Hysteresis 1 Hysteresis 2 DV DD 1 DV DD 2 AV DD 1 AV DD 2 AV DD 3 AV DD 4 VCC VH VL IDD 1 IDD 2 IADD 1 IADD 2 IADD 3 IADD 4 ICC IH IL VT+ VT– VIH1 VIL1 VDCIN VSUB VOH 1 VOL 1 VOH 2 VOL 2 VOH 3 VOL 3 VOH 4 VOL 4 *1,*6, *2,*7 DCIN SUBIN SUBOUT *1,*8 A/D input amplitude = 2Vp-p DV DD 1 = 3.3V DV DD 2 = 3.3V AV DD 1 = 5.0V AV DD 2 = 5.0V AV DD 3 = 5.0V AV DD 4 = 5.0V VCC = 5.0V VH = 15.0V VL = –8.0V IOH 1 = –1.2mA IOL 1 = 2.4mA IOH 2 = –2.4mA IOL 2 = 4.8mA IOH 3 = –8mA IOL 3 = 8mA IOH 4 = –4mA IOL 4 = 5.4mA V V V V V V V V V mA mA mA mA mA mA mA mA mA V V V V V V V V V V 3.0 3.0 4.75 4.75 4.75 4.5 4.5 14.25 –8.5 DV DD 2 · 0.8 DV DD 1 · 0.7 1.0 Display value – 0.1 DV DD 2 – 0.8 DV DD 2 – 0.8 DV DD 1/2 VH – 0.25 3.3 3.3 5.00 5.00 5.00 5.0 5.0 15.00 –8.0 7.0 38.5 3.1 1.0 5.3 16.1 53.5 7.1 1.5 Display value 0.5 0.6 3.6 3.6 5.25 5.25 5.25 5.5 5.25 15.75 –7.5 DV DD 2 · 0.2 DV DD 1 · 0.3 4.5 Display value + 0.1 0.4 0.4 DV DD 1/2 VL + 0.25 Operating current Supply voltage

– 6 – MCX18LG0A/MCX18LG0B OSC CK SIFSEL Item Symbol UnitMin. Typ. Max.Pins Conditions Threshold value Feedback resistance Input amplitude Pull-up resistor DC amplifier gain Input leak current 1 Input leak current 2 Input leak current 3 V TH RFE1 RPU G I II2 II3 OSCI = DVDD 1 or GND 50MHz sine wave VIN = DVDD 2 VIN = GND or DVDD 2 VIN = GND or DVDD 2 V Ω Vp-p Ω µA µA µA 250k 0.5 25k –10 –40 DV DD 1/2 50k 4.4 2.5M 75k *1 CO0 to 7 *2 RESETTG *3 CSEVR, CSROM, SO, TEST, VD, HD, YO0 to 7, CO0 to 7, NRB *4 CASO, CASCK, DCK *5 OSCO *6 XCS, SI, SCK, XCLR, CASI *7 OSCI, CK *8 SIFSEL Note) VSUB display value The VSUB display value is displayed by a code on the rear surface of the MUC. Code — Actual voltage (V)5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 A 7.75 C 8.00 D 8.25 Code E 8.50 f 8.75 G 9.00 h 9.25 J 9.50 K 9.75 L 10.00 m 10.25 N 10.50 P 10.75 R 11.00 S 11.25 U 11.50 V 11.75 Code W 12.00 X 12.25 Y 12.50 Z 12.75Actual voltage (V) Actual voltage (V)

– 7 – MCX18LG0A/MCX18LG0B TSU XC S TH XC S TW LSC K TW H SC K TZD SO TPD SO TD ZSO D ATA D ATAD ATA D ATA D ATA TH SI D ATA TSU SI SI SO SC K XC S TpdYO TpdC O TpdN R B YO 0 to 7 C O 0 to 7 N R B D C K Minimum low interval Minimum low interval SCK input pulse width (high interval) SCK input pulse width (low interval) XCS input setup time, activated by the falling edge of SCK XCS input hold time, activated by the rising edge of SCK SI input setup time, activated by the rising edge of SCK SI input hold time, activated by the rising edge of SCK SO output transition time (Hi-Z fi Data active), activated by the falling edge of XCS SO transition time (Data active fi Hi-Z), activated by the rising edge of XCS SO output delay time, activated by the falling edge of SCK YO0 to 7 output delay time, activated by the falling edge of DCK CO0 to 7 output delay time, activated by the falling edge of DCK NRB output delay time, activated by the falling edge of DCK TW CLR TW RST TWH SCK TWL SCK TSU XCS TH XCS TSU SI TH SI TZD SO TDZ SO TPD SO TPD YO TPD CO TPD NRB 500 430 430 430 640 140 140 200 200 240 ns ns ns ns ns ns ns ns ns ns ns ns ns ns Serial communication Digital output XCLR RESETTG Classification Item Symbol Min. Typ. Max. Unit (CL = 20pF, within recommended operating range)

– 8 – MCX18LG0A/MCX18LG0B Image Sensor Characteristics (Ta = 25°C) Item Sensitivity Saturation signal Smear Dark signal Dark signal shading S Ysat Sm Ydt ∆Ydt 285 700 360 0.007 0.012 mV mV mV mV Center of screen Ta = 60°C, center of screen Ta = 60°C Ta = 60°C Symbol Min. Typ. Max. Unit Measure- ment method Remarks Measurement System C .D .S LPF1AM P C C D O U T Y signal output (3dB dow n 4M H z) [∗Y] [∗A] N ote) Adjust the am plifier gain so that the gain betw een [∗A] and [∗Y] equals 1. M icro unit C C D

– 9 – MCX18LG0A/MCX18LG0B Image Sensor Characteristics Measurement Method Measurement conditions (1)In the following measurements, each supply voltage is at the typical values. (2)In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical black level (OB) is used as the reference for the signal output, which is taken as the value of Y signal output of the measurement system. Definition of Standard Imaging Conditions 1) Standard imaging condition I: Use a pattern box (luminance 706cd/m2, color temperature of 3200K halogen source) as a subject. (Pattern for evaluation is not applicable.) Use a ND2 filter and image at F5.6 or equivalent. The luminous intensity to the sensor receiving surface at this point is defined as the standard sensitivity testing luminous intensity. 2) Standard imaging condition II: Image a light source with a uniformity of brightness within 2% at all angles (color temperature of 3200K). 1. Sensitivity Set to standard imaging condition I. After selecting the electronic shutter mode with a shutter speed of 1/250s, measure the Y signal (Ys) at the center of the screen and substitute the values into the following formula. S = Ys · [mV] 2. Saturation signal Set to standard imaging condition II. After adjusting the luminous intensity to 10 times the intensity applying with an average value of Y signal output, 200mV, measure the minimum value of the Y signal. 3. Smear Set to standard imaging condition II. With using ND2 filter and the lens diaphragm at F5.6 or equivalent, adjust the luminous intensity to 500 times the intensity applying with an average value of Y signal output, 200mV. When the readout clock is stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure the maximum value YSm [mV] of the Y signal output, and substitute the values into the following formula. 4. Dark signal Measure the average value of the Y signal output (Ydt [mV]) with the device ambient temperature of 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 5. Dark signal shading After measuring 4, measure the maximum (Ydmax [mV]) and minimum (Ydmin [mV]) values of the Y signal output, and substitute the values into the following formula. ∆Ydt = Ydmax – Ydmin [mV] Sm = · 100 [%] (1/10V method conversion value)· · 200 YSm 500 250

– 10 – MCX18LG0A/MCX18LG0B Measurement System VID EO O U TM icro unit C C D D igital encoder Optical Characteristics MCX18LG0A Item Focus length Aperture Shading Resolution f F SH SV R 2.9 2.8 220 TV lines Horizontal Vertical Center of screen Symbol Min. Typ. Max. Unit Remarks MCX18LG0B Item Focus length Aperture Shading Resolution f F SH SV R 4.0 2.8 220 TV lines Horizontal Vertical Center of screen Symbol Min. Typ. Max. Unit Remarks

– 11 – MCX18LG0A/MCX18LG0B Communication Code Table 0 to 2 0 to 3 4 to 6 0 to 3 4 to 6 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 5 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 DIGITAL1 DIGITAL2 DIGITAL3 DIGITAL4 DIGITAL5 MODE1 SETUP SUP601 RMATY RMATC BMATY BMATC VDBUSY YGAIN Digital output ON/OFF 0: OFF, 1: ON Digital output ON/OFF 0: OFF, 1: ON Digital output ON/OFF 0: OFF, 1: ON Digital output ON/OFF 0: OFF, 1: ON Digital output ON/OFF 0: OFF, 1: ON Operation mode switching, normally "5h" Setup level 0 (0h) to 8.5 (Fh) IRE Digital output setup ON/OFF 0: OFF, 1: ON Matrix coefficient Matrix coefficient Matrix coefficient Matrix coefficient VD output signal switching 0: VD, 1: SCSBUSY Luminance signal gain D AA BB FF AA Cate- gory Byte Bit Symbol Description EEPROM Address (H) Recommended value (H) Initial value (H)

– 12 – MCX18LG0A/MCX18LG0B 0 to 7 0 to 7 0 to 3 6 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 RBQUAD CONGAIN CONHUE RYGAIN BYGAIN RYHUE BYHUE SHOFST EVRUSR YGAIN VREFY VREFC VSUB Linear matrix quadrant control bit 0: 1st, bit 1: 2nd, bit 2: 3rd, bit 3: 4th 0: invalid, 1: valid Linear matrix gain 0: invalid, 1: valid Linear matrix hue 0: invalid, 1: valid Dummy Linear matrix coefficient Linear matrix coefficient Linear matrix coefficient Linear matrix coefficient Sample-and-hold output offset EEPROM error write prevention 00h: write enabled, A0h: write unenabled Luminance signal gain VREFY adjustment VREFC adjustment VSUB adjustment FC Adjustment value Adjustment value Adjustment value Adjustment value FF FF FF FF FF Adjustment value Adjustment value Adjustment value FC F FF FF FF FF FF 4F, 51, 53, 55*2 50, 52, 54, 56*2 57, 59, 5B, 5D*2 58, 5A, 5C, 5E*2 60* 61*1 62*1 63*1 64*1 Cate- gory Byte Bit Symbol Description EEPROM Address (H) Recommended value (H) Initial value (H)

– 13 – MCX18LG0A/MCX18LG0B Cate- gory Byte 0 to 7 0 to 7 3 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 2 4 to 6 Bit Symbol AGCCONT SHTSPDM SHTHL SHTON SHTSPDL WBR AWBCNTL WBG AWBCNTM WBB INTGRL INTGR INTGRM AWBADJUST AWB AEADJUST AE MCR SPRS

Description

Shutter speed (lower 8 bits, MSB) Electronic shutter high speed/low speed switching 0: high speed, 1: low speed Electronic shutter ON/OFF 0: OFF, 1: ON Shutter speed (upper 8 bits) Write White balance control Read ATW adjustment integral data Write White balance control Read ATW adjustment integral data Write White balance control Read ATW adjustment integral data Write White balance control Read ATW adjustment integral data Write Read ATW adjustment integral data AWB adjustment mode switching 0h: OFF, 2h: ON AWB control 0: ON, 1: OFF AE adjustment mode switching 0h: OFF, 3h: ON AE control 0: ON, 1: OFF Microcontroller control 0: ON, 1: OFF Suppress control 0: ON, 1: OFF EEPROM Address (H) Recommended value (H) Initial value (H) FF FF

– 14 – MCX18LG0A/MCX18LG0B 4 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 SW FLON BLCOF AEREF AWB1 E2WR E2WEN E2LSB E2RSW E2RAL1 E2RAL2 E2RAL3 E2RAL4 E2CODE E2ADRS E2DATA SPCODE SPCDAT Serial communication based AE/AWB mode switching 0: invalid, 1: valid Flickerless ON/OFF 0: OFF, 1: ON Backlight compensation ON/OFF 0: ON, 1: OFF AE convergence level switching 0: 100 IRE, 1: [AWB] setting with USR AWB mode setting EEPROM write control 0: OFF, 1: Write EEPROM write enable send 0: OFF, 1: Send EEPROM lower 8 bits selection 0: upper 8 bits, 1: lower 8 bits EEPROM read control 0: OFF, 1: ON EEPROM read range specification 0: OFF, 1: Select EEPROM read range specification 0: OFF, 1: Select EEPROM read range specification 0: OFF, 1: Select EEPROM read range specification 0: OFF, 1: Select EEPROM control code EEPROM address EEPROM data (upper 8 bits) SPEC code SPEC data 0: Auto 1: Fixed AWB2 AWB3 (AWB2, AWB3) = (AWB2, AWB3) = (1, 0): Pull-in(1, 0): [AWB] USRR/B (0, 1): 4,200K (1, 1): 6,300K Cate- gory Byte Bit Symbol Description EEPROM Address (H) Recommended value (H) Initial value (H)

– 15 – MCX18LG0A/MCX18LG0B 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 5 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 0 to 7 5 to 7 2 to 3 E2DATAL DIGITAL6 PGON PGCOLSEL PGCOL PGHV PGRSTR PGPTSEL EEPROM data (lower 8 bits) Digital output ON/OFF 0: OFF, 1: ON Pattern generator ON/OFF 0: OFF, 1: ON Color bar/monochrome switching 0: Color bar, 1: Monochrome Color specification 0h: OFF, 1h: Blue, 2h: Red, 3h: Magenta, 4h: Green, 5h: Cyan, 6h: Yellow, 7h: White Horizontal/vertical switching 0: H, 1: V Raster setting 0: OFF, 1: ON Pattern switching 0h: OFF, 1h: ramp, 2h: impulse, 3h: invert impulse 65* 66*1 67*1 68*1 69*1 6A*1 6B*1 6C *1 6D *1 Cate- gory Byte Bit Symbol Description EEPROM Address (H) Recommended value (H) Initial value (H)

– 16 – MCX18LG0A/MCX18LG0B 6 to 7 0 to 7 0 to 7 0 to 7 0 to 7 Cate- gory Byte Bit Symbol Description EEPROM Address (H) Recommended value (H) Initial value (H) 1 Lower 8 bits used. Without a "*1", upper 8 bits used. *2 (1st, 2nd, 3rd, 4th) quadrant

– 17 – MCX18LG0A/MCX18LG0B Code (H) Address (H) Symbol [AE] SPD [AE] USR [AE] MAX [AE] MIN [AE] LIM [AE] BLC [AE] HIST [AWB] SPD [AWB] FRM [AWB] RSFT [AWB] BSFT [AWB] USRR [AWB] USRB [AWB] RGAIN1 [AWB] BGAIN1 RYGAIN1 BYGAIN1 RYGAIN2 Recommended value (H) BB Adjustment value EE Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Initial value (H) BB EE AE shutter speed upper limit Backlight compensation control Histogram backlight compensation control bit0 to 3: AWB response speed bit4 to 7: fixed to "1h" AWB detection window setting Manual mode shift volume setting Manual mode shift volume setting User mode setting User mode setting R gain for 3,200K B gain for 3,200K R-Y GAIN (1st) B-Y GAIN (1st) R-Y GAIN (2nd) SPEC Code Table

– 18 – MCX18LG0A/MCX18LG0B BYGAIN2 RYGAIN3 BYGAIN3 RYGAIN4 BYGAIN4 RYHUE1 BYHUE1 RYHUE2 BYHUE2 RYHUE3 BYHUE3 RYHUE4 BYHUE4 MODE2 [AWB] RBL [AWB] RBM [AWB] RBGL [AWB] RBGM [AWB] RGAIN2 [AWB] BGAIN2 [AWB] GLIM [AWB] BLIM Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value Adjustment value B-Y GAIN (2nd) R-Y GAIN (3rd) B-Y GAIN (3rd) R-Y GAIN (4th) B-Y GAIN (4th) R-Y HUE (1st) B-Y HUE (1st) R-Y HUE (2nd) B-Y HUE (2nd) R-Y HUE (3rd) B-Y HUE (3rd) R-Y HUE (4th) B-Y HUE (4th) Operation mode switching, normally "80h" ATW operation frame adjustment data ATW operation frame adjustment data ATW operation frame adjustment data ATW operation frame adjustment data R gain for 9,500K B gain for 9,500K ATW operation frame adjustment data ATW operation frame adjustment data Code (H) Address (H)Symbol Recommended value (H) Initial value (H)Description

– 19 – MCX18LG0A/MCX18LG0B 21D C K C O 0 to 7 D C K 64D C K 60D C K D C K = 13.5M H z (74.07ns) 145D C K R -Y H D (BLK) N R B YO 0 to 7 Horizontal Timing Chart VD H D (BLK) 1 3 5 7 9 11 2 4 6 8 10YO /C O 486 488 490 492 485 487 489 491 VD H D (BLK) 1 3 5 7 9 2 4 6 8 10YO /C O 485 487 489 491 484 486 488 490 492 O D D Field EVEN Field O ptical Black (BLK) is an internal pulse. YO 0 to 7 and C O 0 to 7 signals are processed by BLK pulse. Vertical Timing Chart

– 20 – MCX18LG0A/MCX18LG0B Notes on Handling 1)Static charge prevention Micro unit CCDs are easily damaged by static discharge. Before handling be sure to take the following protective measures. a)Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive shoes. b)When handling directly use an earth band. c)Install a conductive mat on the floor or working table to prevent the generation of static electricity. d)Ionized air is recommended for discharge when handling micro unit CCD. e)For the shipment of mounted substrates, use boxes treated for the prevention of static charges. 2)Please use IC socket for mounting of micro unit CCD. IC socket : HS6401-K YAMATO SCIENTIFIC CO., LTD. 3)Dust and dirt protection a)Operate in clean environments. b)Do not either touch lens by hand or have any object come in contact with glass surfaces. Should dirt stick to a lens surface, blow it off with an air blower. (For dirt stuck through static electricity ionized air is recommended.) c)Clean with a cotton bud and ethyl alcohol if the grease stained. Be careful not to scratch the lens. d)Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. 4)Do not expose to strong light (sun rays) for long periods. 5)Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. 6)Micro unit CCDs are precise optical equipment that should not be subject to mechanical shocks.

– 21 – MCX18LG0A/MCX18LG0B R 105 47k R 106 47k R 107 47k R 104 100k C 121 0.1µ C 120 10p X101 27M H z C 119 10p R 103 270 C 118 1000p C 117 0.1µ C 116 10µ/16V C 107 0.1µ C 108 2.2µ/20V C 109 0.1µ C 106 0.1µ C 105 0.1µ C 101 0.1µ C 102 10µ/20V L102 100µH L105 10µH R 102 R 101 100k 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 41424344454647484950515253545556 D G N D D C K YO 7 YO 6 YO 5 YO 4 YO 3 YO 2 YO 1 YO 0 D VD D 2 SH O U T SH IN AG N D C C D O U T AG N D SI SO C ASI C SR O M R ESETTG D G N D O SC I O SC O C K D VD D 1 XC S C ASC K C ASO C SEVR D G N D VL DGND DGND CO7 CO6 CO5 CO4 CO3 CO2 CO1 CO0 NRB HD VD TEST XCLR SCK SIFSEL AGND VH AGND AVDD4 VCC AGND SUBIN AGCCONT OFFSET AVDD1 AVDD2 AVDD3 DCIN DCOUT SUBOUT C 114 1000p D 101 M A159A (2/2) D 101 M A159A (1/2) L106 10µH L107 100µH C 110 22µ/20V C 112 1µ/35V C 113 0.1µ C 115 0.1µ C 122 0.1µ

1 VSS

81 C S

+15V +5V –8V IC 101 M C X18LG 0A/B +3.3V SO SI YO [0 to 7] D C K C O [0 to 7] N R B H D VD L103 10µH L104 10µH C 124 0.1µ L101 10µHC 123 100µ/6.3V C 103 0.1µ C 104 10µ/6.3V C 111 6.8µ/20V OUT VDD VSS IC 104 S-80730AN

– 22 – MCX18LG0A/MCX18LG0B PAC KAG E STR U C TU R E PAC KAG E M ATER IAL LEAD TR EATM EN T LEAD M ATER IAL PAC KAG E W EIG H T 16.08 ± 0.2 1st. pin Index. 16.2 64 - 0.80 7.6 3.5 ± 0.4 7.30 ± 0.5 8.37 ± 0.5 18.28 ± 0.3 35°2° 0.30m in 5.50m ax 3.20max. 5.50max 2-1.50m ax 2-1.50max 18.28 ± 0.3 7.6 Ø1.04 816457 3.20m ax. 64-R (0.25) P1.016 X 15 = 15.24 64 - 0.50 64pin Q FN (720m il) Au 4.20g ceram ic Package Outline Unit: mm MCX18LG0A

– 23 – MCX18LG0A/MCX18LG0B PAC KAG E STR U C TU R E PAC KAG E M ATER IAL LEAD TR EATM EN T LEAD M ATER IAL PAC KAG E W EIG H T 16.08 ± 0.2 1st. pin Index. 16.2 64 - 0.80 7.6 3.5 ± 0.4 8.50 ± 0.5 9.57 ± 0.5 18.28 ± 0.3 35°2° 0.30m in 5.50m ax 3.20max. 5.50max 2-1.50m ax 2-1.50max 18.28 ± 0.3 7.6 Ø1.04 816457 3.20m ax. 64-R (0.25) P1.016 X 15 = 15.24 64 - 0.50 64pin Q FN (720m il) Au 4.20g ceram ic Package Outline Unit: mm MCX18LG0B