MCC400-600 XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

  • Baseplate-cooled
  • Up to4 RegulatedOutputs
  • Op tional200 W ConditionedOutput
  • MIL-STD 1275 and DEF-STAN 61-5
  • MIL-STD 461 and DEF-STAN 59-411
  • Rugged ConstructiontoMIL-STD 810F
  • 3 YearWa rranty MCC Series Input InputVoltageRange • 18.5-34 VDC steady state InputCurrent • 27 A at 18.5 V max InrushCurrent • <60 A InputReverse Voltage • Continuous Protection InputTransient • MIL-STD-1275A/B/C/D UndervoltageLockout • Vin <18 VDC Ou tput Output Voltage • O/P 1-4: regulated outputs 2-48 VDC Output Voltage • O/P 1-4: 10-110% factory set Adjustment A minimum load of 10% is required for outputs below 90% of nominal voltage OptionalAux. • Vin - 2 VDC (1) Output RailVoltage OptionalAux. • 200 W for MCC600 (9 A max) Output Power Maximum Aux. Output • Vout clamped <36 VDC Minimum Load • No minimum load (output ripple increased at Pout <10% Pout max) LineRegulation • 1% max Load Regulation • 1% max Cross Regulation • Outputs 1-4 individually regulated, no cross regulation Output Set Tolerance • ±100 mV ExternalHold Up • External connection for additional hold up capacitance, see longform datasheet Ripple& Noise • 50 mV or 1% pk-pk, whichever is the greater, 20 MHz bandwidth Low Noise (Option‘Q’) • Outputs 1 & 2: 25 mV reduction Outputs 3 & 4: 45 mV reduction Temperature Coefficient • ±0.05% /˚C OvervoltageProtection • 110-120% of nominal output, recycle input to restart OvercurrentProtection • 110-120% of nominal output, auto recovery ShortCircuitProtection • Continuous, with auto restart Overtemperature • >+90 ˚C baseplate temperature, Protection auto restart Remote Sense • Outputs 1 & 2, Compensate for 0.5 V total voltage drop xppo w er.com Ge neral Efficiency • 75% typical IsolationVoltage • 500 VDC Input to Output,

500 VDC Output to Chassis,

500 VDC Input to Chassis

Materialand Finish • Aluminium baseplate and safety cover InputInhibit • Global enable and disable function, short to negative input to inhibit Output Inhibit • Each regulated output has independent inhibit, TTL high to inhibit InhibitedInputCurrent • <5 mA when input inhibit function is used DC OK Signal • Optional on output voltages ≥5 VDC Isolated opto-coupler transistor output MTBF • 517 kHrs to MIL-HDBK-217F at 40 ˚C, GB Environm ental OperatingTemperature • -40 ˚C to +70 ˚C ambient with baseplate temperature within -40 ˚C to +90 ˚C Extended Temperature • -55 ˚C to +90 ˚C baseplate temperature, (see note 4) Cooling • Baseplate-cooled. It is recommended that a thermal pad or compound is fitted between the MCC baseplate and any heatsink OperatingHumidity • 20-95% non-condensing Storage Temperature • -55 ˚C to +90 ˚C Storage Humidity • 20-95% non-condensing Shock • 40 g MIL-STD-810F, method 516.5-1 Vibration • MIL-STD-810F, method 514.5C-17 minimum integrity test for military equipment EMC Emissions • EN55022 Level B conducted MIL-STD-461E/F army ground use CE101 & CE102 DEF-STAN 59-411, DCE01/DCE02 Conducted Immunity • MIL-STD-1275A/B/C/D, MIL-STD-461E/F CS101, CS114, CS115, CS116 DEF-STAN 61-5 part 6 issue 5 (1) Vin - 2VDC minim um 36 VDC (clam ped) maximum

M odelNumber & Ratings Mec hanicalDetails MC C400/600 MC C 400-600:C N 1 25-Pin InputCon nector Pin Function Pin Function

1 DC OK 14 DC OK RTN

2 Global Inhibit 15 Global Inhibit RTN

3 N/C 16 Negative Input

4 Negative Input 17 Negative Input

5 Negative Input 18 Negative Input

6 Negative Input 19 Negative Input

7 Negative Input 20 Negative Input

8 Negative Input 21 Positive Input

9 Positive Input 22 Positive Input

10 Positive Input 23 Positive Input

11 Positive Input 24 Positive Input

12 Positive Input 25 Positive Input

13 Positive Input

M C C 400-600:C N 29-Pin A ux O utputC onnector Pin Function Pin Function

1 External Holdup Positive 6 External Holdup Negative

2 External Holdup Positive 7 External Holdup Negative

3 N/C 8 Aux Output Negative

4 Aux Output Positive 9 Aux Output Negative

5 Aux Output Positive

M C C 400-600:SignalsC onnector Pin Function Pin Function

1 Disable 4 DC OK RTN

  1. Modules 1 to 4 available for MCC400/600 e.g. MCC4Q2D2J2L2PED. 2. 4 series output modules to be used with single MCC400/600 models only. 3. DC-DC output modules are stress-screened for -55 ˚C to +90 ˚C operation. 4. Low cost option with passive EMI filtering only. No auxiliary output, EMI to EN55022 level B only. 5. Global inhibit will also turn off the auxiliary output - Option A. S - Standard E - Screening option (3) A - Auxiliary Turn Off (5) D - DC OK, leave blankif not required Q - Low noise output L - Passive filtering only (4) P - Conformal coating 1 2 3 4 M C C4 00/6 00: Single (S), Dual (D), Triple (T) or Quad (Q) (4 slots max where all slots must be filled) M odules O utputVoltage / C urrentRa ting V I W Slots C ode 3.3 22.7 A 75 W 1 2C 3.3 45.4 A 150 W 2 3C 3.3 80.0 A 264 W 4 4C (2) 5 20.0 A 100 W 1 2D 5 40.0 A 200 W 2 3D 5 80.0 A 400 W 4 4D (2) 12 8.3 A 100 W 1 2J 12 16.6 A 200 W 2 3J 12 33.3 A 400 W 4 4J (2) 15 6.6 A 100 W 1 2L 15 13.3 A 200 W 2 3L 15 26.7 A 400 W 4 4L (2) 24 4.1 A 100 W 1 2P 24 8.3 A 200 W 2 3P 24 16.7 A 400 W 4 4P (2) 28 3.5 A 100 W 1 2Q 28 7.1 A 200 W 2 3Q 28 14.3 A 400 W 4 4Q (2) 36 2.78 A 100 W 1 2T 36 5.56 A 200 W 2 3T 36 11.11 A 400 W 4 4T 48 2.1 A 100 W 1 2W 48 4.1 A 200 W 2 3W 48 8.3 A 400 W 4 4W (2) C hassis De signations,Power & Sizes Code Pow er Slots MCC4 400 W 4 MCC6 400 W + 200 W Aux 4 M CC 4 Q 2J 2J 2J 2J E X X X X Harwin 2mm Datamate Connector. Horizontal male. p/n: M80-8410642 Mates with p/n: M80-8890605 Signal Connector 3 2 1 6 5 M4 output studs polarity marked on PCB silk screen. Output polarity varies for multiple outputs. 1 2 = 1. All dimensions are in inches (mm). 2. Weight: MCC400/600: 2.31 lb (1.05kg) max. 3. Tolerance: ±0.008 in (±0.2 mm). 4. Max Torque: M4 studs 17.7 lbs-in (2.0 Nm) 5. For mating signal connector kit order part number MCC-SIG CON KIT MCC 400-600

4 SLOT S

1.083 (27.5) 6.496 (165.0) 6.102 (155.0) 5.630 (143.0) 0.886 (22.5) 7.283 (185.0) CN1 CN2 Auxiliary output and external hold-up connector: 9-way D sub socket Input control and alarm connector: 25-way D sub plug 6 x user fixing holes 4 20 2.756 (70.0) 2.756 (70.0) 0.756 (19.2) 1 13 14 25 5 1 9 6 CN1 CN2 Notes Notes