MC2213 FPE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 3

Technical content

Features: Applications: Large Current and Low DCR. Voltage Regulator Module (VRM) Magnetically shielded construction. Multi-phase regulators High frequency range up to 3.0 MHz. Point-of-load modules RoHS compliant* and halogen free. Desktop and server VRMs and EVRDs Low noise. Data networking and storage systems Operating temperature range: -55℃ TO +125℃ Base station equipment Battery power systems Product identification: L× W HT Dimensions (unit:inch/ mm): Recommended Layout: [unit: inch/ mm] Note：

  • All test date is referenced to 25℃ ambient.
  • DC current(ldc) that will cause an approximate △T of 40℃.
  • DC current(last) that will cause Lo to drop approximately 30%.
  • Operating temperature range:-55℃ to +125℃.
  • The part temperature (ambient + temp rise) should not exceed125℃ under the worst operating conditions. Circuit design, component placement, PWB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. 1.6 1.77 0.7 100KHz 0.25V 0.8 Idc (Amp) Typical L0(μH) ±20% '@0A D.C.R (mΩ) COMPOSITE FORMING SMD INDUCTORS 50 70 Electrical Specifications @ 25℃ Heat Rating Current Typical Max MC2213-220M1 3.3 1.0 Saturation Current P/N MC2213-100M1 10 30 Isat (Amp) Typical MC2213-1R0M1 MC2213-3R3M1 3.8 4.2 22 9.2 11 20 15 MC2213-330M1 33 13.5 15.4 18 17.7 1047 15.2 15 MC2213-680M1 68 26.5 29.5 14 12 MC2213-470M1 Product code Inductance value Tolerance Serial code 8MC2213-101M1 36100 6.440 4842.51.31.12.2MC2213-2R2M1 38372.21.94.7MC2213-4R7M1 36353.12.76.8MC2213-6R8M1 24176.04.915MC2213-150M1 910353182MC2213-820M1 XXX XXX

1）Reel dimensions 2) Tape packaging dimensions 3） Tape Direction 4） Peel force of top cover tape The peel speed shall be about 300 mm/minute The peel force of top cover tape shall be between 0.1 to 1.3N Numbers of taping: 100 pieces / reel. 165～185° 0.1～0.7N Carrier tape A=44±1 B=4.0±0.4 44±0.3 20.2±0.1 32±0.1 0.5±0.05 0.5±0.05

Please pay sufficient attention to the warnings for safe designing when using these products. ※ The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40° C, Humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. ※ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). ※ Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150° C. ※ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. ※ Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. ※ Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. Tel: +86 -769 -86761589 http://www.fpe.com.cn