MC0530 FPE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 3
Technical content
Features: Applications: Large Current and Low DCR. Notebooks/Desktops/Server applications. Magnetically shielded construction. Low profile, high current power supplies. High frequency range up to 1.0 MHz. Battery powered devices. RoHS compliant* and halogen free. DC/DC converters. Low noise. Operating temperature range: -40℃ TO +125℃ Product identification: L× W HT Dimensions (unit:inch/ mm): Recommended Layout: [unit: inch/ mm] Note：
- All test date is referenced to 25℃ ambient.
- DC current(ldc) that will cause an approximate △T of 40℃.
- DC current(last) that will cause Lo to drop approximately 30%.
- Operating temperature range:-40℃ to +125℃.
- The part temperature (ambient + temp rise) should not exceed125℃ under the worst operating conditions. Circuit design, component placement, PWB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application. 3.52.512611310MC0530-100M1 Product code Inductance value Tolerance Serial code MC0530-1R0M1 1 13.5 15 6.5 0.47 0.68 10.8 9.5 MC0530-6R8M1 6.8 80 90 3.2 4 MC0530-4R7M1 4.7 54 60 4 5 MC0530-3R3M1 3.3 35 40 4.5 6 21 25 6 9 MC0530-2R2M1 2.2 25 29 5.5 MC0530-R22M1 MC0530-R33M1 MC0530-R47M1 MC0530-R68M1 7.6 8.5 12 8 11 D.C.R (mΩ) MC0530-1R5M1 0.33 0.22 Saturation Current 1.5 COMPOSITE FORMING SMD INDUCTORS 15.8 18 Electrical Specifications @ 25℃ Heat Rating Current Typical Max P/N Isat (Amp) Typical 5.0 5.5 3.9 100KHz 0.25V 4.23 Idc (Amp) Typical L0(μH) ±20% '@0A
1）Reel dimensions 2) Tape packaging dimensions 3） Tape Direction 4） Peel force of top cover tape The peel speed shall be about 300 mm/minute The peel force of top cover tape shall be between 0.1 to 1.3N Numbers of taping: 1500 pieces / reel. 165～185° 0.1～0.7N Carrier tape
Please pay sufficient attention to the warnings for safe designing when using these products. ※ The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40° C, Humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. ※ Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). ※ Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150° C. ※ Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. ※ Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. ※ Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. Tel: +86 -769 - 86761589 http://www.fpe.com.cn