MA5 TIMOTION | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 11
Technical content
TiMOTION's MA5 electric linear actuator is specifically designed for applications that face harsh working environments and require ruggedness and durability. Its IP69K protection can withstand high-pressure water jets, and the ingress of dust and other solid contaminants. The MA5 can also be customized with various feedback options depending on the application requirements; moreover, it can be equipped with a grease nipple to increase the protection degree and life cycle. Suitable applications for MA5 include agricultural equipment, such as valves, spreaders, harvesters, and grain handlers. General Features Max. load 3,500N (push); 2,000N (pull) Max. speed at max. load 2.4mm/s Max. speed at no load 56.5mm/s Retracted length ≥ 200mm (depending on chosen options) IP rating IP69K Stroke 20~1000mm Output signals Mechanical pot., NPN Hall sensor Options Grease chamber Voltage 12/24/48V DC; 12/24/48V DC (PTC) Operational temperature range -25°C~+65°C Operational temperature range +5°C~+45°C at full performance Product Segments
- Industrial Motion MA5 series
(mm) With Grease Chamber Standard Dimensions (mm) Drawing 157 .5 85.7 61 .6 30.8 30.8 61 .6 33.3 Retracted Length ø20 135° ø20 Retracted Length 157 .8 33.3 30.8 61 .685.7 61 .6 30.8
CODE Load (N) Self Locking Force (N) Typical Current (A) Typical Speed (mm/s) Push Pull No Load 24V DC With Load 24V DC No Load 24V DC With Load 24V DC Motor Speed (5200RPM, duty cycle 25%) A 250 250 250 1.2 2.3 43.0 36.0 B 500 500 500 1.1 2.3 25.8 23.0 C 1000 1000 1000 1.1 2.3 14.0 11.8 D 1500 1500 1500 1.0 2.2 9.0 8.0 E 2000 2000 2000 1.0 2.2 7.1 6.2 W 500 500 500 1.3 5.0 54.0 35.0 Motor Speed (6600RPM, duty cycle 25%) F 250 250 250 1.6 2.8 56.5 45.0 G 500 500 500 1.5 2.8 32.5 28.5 H 1000 1000 1000 1.5 2.8 16.5 14.3 K 1500 1500 1500 1.3 2.8 11.1 10.0 L 2000 2000 2000 1.3 2.8 8.8 7.7 Motor Speed (3800RPM, duty cycle 25%) S 3500 2000 3500 0.9 2.8 3.2 2.4 Motor Speed (2200RPM, duty cycle 25%) T 2000 2000 2000 0.3 1.2 3.2 2.4 Note 1 Please refer to the approved drawing for the final authentic value. 2 This self locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages. 4 The current & speed in table are tested when the actuator is extending under push load. 5 The current & speed in table and diagram are tested with TiMOTION control boxes, and there will be around 10% tolerance depending on different models of the control box. (Under no load condition, the voltage is around 32V DC. At rated load, the voltage output will be around 24V DC)
6 Without load, noise level ≤ 78dBA (by TiMOTION test standard, ambient noise level ≤ 36dBA)
7 Standard stroke: Min. ≥ 20mm, Max. please refer to below table. CODE Load (N) Max Stroke (mm) A, F ≤ 250 1000 B, G, W ≤ 750 800 C, H ≤ 1000 600 D, K ≤ 1500 500 E, L, T ≤ 2000 450 S ≤ 3500 300
Motor Speed (5200RPM) Performance Data (24V DC Motor) MA5 series 10.0 0.0 20.0 30.0 40.0 50.0 60.0 0 2000 40001000 3000 5000 6000 A W B C ED Speed (mm/s) Speed vs. Load Load (N) 1.0 0.0 2.0 3.0 4.0 5.0 6.0 0 2000 40001000 3000 5000 6000 A W B C ED Current (A) Current vs. Load Load (N)
Motor Speed (6600RPM) Performance Data (24V DC Motor) MA5 series 10.0 0.0 20.0 30.0 40.0 50.0 60.0 0 2000 40001000 3000 5000 6000 F G H L K Speed (mm/s) Speed vs. Load Load (N) 1.0 0.0 2.0 3.0 4.0 5.0 6.0 0 2000 40001000 3000 5000 6000 F G H LK Current (A) Current vs. Load Load (N)
Motor Speed (3800RPM) Performance Data (24V DC Motor) MA5 series 1.0 0.0 2.0 3.0 4.0 5.0 0 2000 40001000 3000 5000 S 6.0 6000 Speed (mm/s) Speed vs. Load Load (N) 1.0 0.0 2.0 3.0 4.0 5.0 0 2000 40001000 3000 5000 S 6.0 6000 Current (A) Current vs. Load Load (N)
Motor Speed (2200RPM) Performance Data (24V DC Motor) MA5 series 1.0 0.0 2.0 3.0 4.0 5.0 0 2000 40001000 3000 5000 T 6.0 6000 Speed (mm/s) Speed vs. Load Load (N) 1.0 0.0 2.0 3.0 4.0 5.0 0 2000 40001000 3000 5000 T 6.0 6000 Current (A) Current vs. Load Load (N)
Version: 20230802-F Load and Speed Voltage Cable Length (mm) Output Signals IP Rating Wiper Set & Grease Nipple Connector See page 11 Direction of Rear Attachment (Counterclockwise) See page 10 1 = 12V DC 2 = 24V DC 4 = 48V DC 6 = 12V DC, PTC 5 = 24V DC, PTC 8 = 48V DC, PTC 1 = Straight, 300 2 = Straight, 600 3 = Straight, 1000 0 = Without 1 = Mechanical pot. N = NPN Hall sensor*2 6 = IP66M 9 = IP69K 0 = Normal wiper, without grease chamber 1 = Enhanced wiper set, with grease chamber, grease nipple * 1 2 = Enhanced wiper set, with grease chamber, grease nipple * 2 3 = Enhanced wiper set, with grease chamber, without grease nipple 1 = DIN 6P , 90° plug 2 = Tinned leads 1 = 90° 2 = 0° Stroke (mm) Retracted Length (mm) Functions for Limit Switches See page 11 1 = Two switches cut off the actuator at end of stroke (EOS) 2 = Two switches cut off the actuator at EOS + in-between third one sends signal 3 = Two switches send signal at EOS 4 = Two switches send signal at EOS + third one in between sends signal See page 3 See page 3 See page 9 Rear Attachment (mm) See page 10 Front Attachment (mm) See page 10 4 = Aluminum, U clevis, slot 6.0, width 10.5, hole 6.4, one piece casting with gearbox 5 = Aluminum, U clevis, slot 6.0, width 10.5, hole 8.0, one piece casting with gearbox 6 = Aluminum, U clevis, slot 6.0, width 10.5, hole 10.1, one piece casting with gearbox 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 10.0 4 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 6.4 5 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 8.0
- Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y 3. The total Retacted length calculated must be equal or longer than below minimum value (1) When choosing the wiper set #0: And the front attachment is #1, #2, min retracted length ≥ 200mm, And the front attachment is #3, #4, #5, min retracted length ≥ 212mm (2) When choosing the wiper set #1, #2, #3: And the front attachment is #1, #2min retracted length ≥ 238mm, And the front attachment is #3, #4, #5min retracted length ≥ 250mm Retracted Length (mm) C. Ouput Signals 0, N - 1 +30 D. Wiper Set & Grease Nipple 0 - 1, 2, 3 +10 B. Load V.S. Stroke Stroke (mm) Load (N) < 3500 = 3500 20 ~150 - +5 151~200 +2 +7 201~250 +2 +7 251~300 +2 +7 301~350 +12 +17 351~400 +22 +27 401~450 +32 +37 451~500 +42 +47 501~550 +52 +57 551~600 +62 +67 601~650 +72 +77 651~700 +82 +87 701~750 +92 +97 751~800 +102 +107 801~850 +112 +117 851~900 +122 +127 901~950 +132 +137 951~1000 +142 +147 A. Front Attachment 1, 2 +112 3, 4, 5 +124
Rear Attachment (mm) 4 = Aluminum, U clevis, slot 6.0, width 10.5, hole 6.4, one piece casting with gearbox 5 = Aluminum, U clevis, slot 6.0, width 10.5, hole 8.0, one piece casting with gearbox 6 = Aluminum, U clevis, slot 6.0, width 10.5, hole 10.1, one piece casting with gearbox 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 10.0 4 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 6.4 5 = Aluminum, U clevis, slot 6.0, depth 16.0, hole 8.0 Front Attachment (mm) ø6.4 ø20 9 9 ø8ø20 ø10 ø20 ø6.4 ø20 ø20 Direction of Rear Attachment (Counterclockwise) 1 = 90° 2 = 0° 10.5 R11 ø6.4 10.5 R11 10.5 R11 ø10.1 Hole Hole 90º
Functions for Limit Switches Wire Definitions CODE Pin 1 (Green) 2 (Red) 3 (White) 4 (Black) 5 (Yellow) 6 (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch Connector 1 = DIN 6P , 90° plug 2 = Tinned leads Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.