MA4 TIMOTION | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 8

Technical content

  • Industrial Motion General Features Max. load 2,000N (push/pull) Max. speed at max. load 6.1mm/s Max. speed at no load 46.1mm/s Retracted length ≥ 215mm (depending on chosen options) IP rating IP69K Stroke 25~1000mm Output signals Adjustable Reed switch, mechanical Pot., Hall sensor(s), NPN Hall sensors Options T-Smart Voltage 12/24V DC; 12/24V DC (thermal switch) Operational temperature range -40°C~+85°C Operational temperature range +5°C~+45°C at full performance Manual drive TiMOTION's MA4 series is a compact electric linear actuator, suited for almost any working condition. Furthermore, the MA4 has an optional T-Smart version. Embedded with a TiMOTION driver board, the MA4 allows for easy integration with different control interfaces, eliminating the need of an external control box. The MA4 is available in three T-Smart alternatives: 1)T-Smart Advanced The T-Smart Advanced alternative allows for synchronization of up to 8 actuators, as well as accurate position feedback through a variety of options (Hall, Hall-Pot., PWM). 2) T-Smart SAE J1939 This alternative provides seamless integration with CAN bus SAE J1939 interfaces, the standardized communication protocol commonly implemented in off-road vehicles and other industrial applications. 3)T-Smart Modbus Modbus is a serial communication protocol predominantly used in industrial automation and process control. The T-Smart Modbus alternative can be smoothly incorporated into existing industrial systems. All T-Smart alternatives are compatible with TiMOTION’s software program, PGMA, providing the user autonomy to adjust parameters such as speed, stroke limits, soft stop, soft start, and much more.

1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured in 24V DC. With a 48V DC motor, the current is approximately half the current measured in 24V DC. Speed will be similar for all the voltages. 3 The current & speed in table are tested when the actuator is extending under push load. 4 With load, noise level ≤ 80dBA (by TiMOTION test standard, ambient noise level ≤ 36dBA). 5 Standard stroke: Min. 25 mm, Max. please refer to the table below. MA4 series Standard Dimensions (mm) Drawing CODE Load (N) Max Stroke (mm) A ≤ 250 1000 B ≤ 500 800 C ≤ 1000 600 D ≤ 1500 500 E ≤ 2000 450 Load and Speed CODE Load (N) Self Locking Force (N) Typical Current (A) Typical Speed (mm/s) Push Pull No Load 24V DC With Load 24V DC No Load 24V DC With Load 24V DC Motor Speed (6000RPM, Duty Cycle 25%) A 250 250 325 0.8 1.2 46.1 42.6 B 500 500 650 0.8 1.7 29.5 25.8 C 1000 1000 1300 0.8 2.2 14.8 12.2 D 1500 1500 1950 1.0 2.2 9.8 8.2 E 2000 2000 2600 1.0 2.2 7.4 6.1 Retracted Length 10.4 R9.420 7 4.4 32.5

Motor Speed (6000RPM, Duty Cycle 25%) Performance Data (24V DC Motor) MA4 series E C B A D 0 20001000 3000 4000 0.0 10.0 20.0 30.0 60.0 40.0 50.0 Speed (mm/s) Speed vs. Load Load (N) 1.0 0.0 2.0 3.0 4.0 6.0 5.0 EC B A D 0 20001000 3000 4000 Current (A) Current vs. Load Load (N)

Version: 20231106-F Voltage 1 = 12V DC 2 = 24V DC 6 = 12V DC, thermal switch 5 = 24V DC, thermal switch Type Front Attachment (mm) See page 6 Adjustable Reed Switch Output Signal See page 8 A1/P1 Connecter (mm) See page 7 P2 Connector Cable Exit A1/P1 Cable Length (mm) P2 Cable Length (mm) Alternative Packaging (mm2) Function of Limit Switches N = Normal T = T-Smart 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, slotless, hole 10.0 4 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 6.4 5 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 8.0 6 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 10.0 0 = Without 1 = Reed switch*1, tinned leads 2 = Reed switch*2, tinned leads 0 = Without 1 = Mechanical Pot. 4 = Hall sensor*1 5 = Hall sensor*2 N = *NPN Hall sensor*2 01 = Tinned leads, core wire 50, stripped wire 10 0P = Rubber plug T = Direct cable out, 1+1 type 0500 = 500 1000 = 1000 1500 = 1500 2000 = 2000 0000 = Without N = Normal T= Advanced J = SAE J1939 (J1939 default, 250kbps) K = SAE J1939 (500kbps) M = Modbus 0 = Sample packaging C = Standard package, US fumigated pallet (1219*1016) 1 = Standard package, EU fumigated pallet (1200*800) 2 = Standard package, EU fumigated pallet (1500*800) E = Standard package, US plywood pallet (1219*1016) 5 = Standard package, EU plywood pallet (1200*800) 6 = Standard package, EU plywood pallet (1500*800) 1 = Two micro switches cut off the actuator at end of stroke 3 = Two micro switches send signal at end of stroke (signal type: normally closed) Load & Speed Direction of Rear Attachment (Counterclockwise) See page 7 1 = 0° 3 = 90° Stroke (mm) Rear Attachment (mm) See page 6 Retracted Length (mm) 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, slotless, hole 10.0 4 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 6.4 5 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 8.0 6 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 10.0 IP Rating 1 = Without 6 = IP66M 7 = IP67 8 = IP68 9 = IP69K See page 2 See page 2 See page 5

Retracted Length (mm) 1. If stroke ≤ 108mm, minimum retracted length refer to the chart below 2. If Stroke ≥ 109mm, Calculate A+B+C=Y 3. Minimum retracted length is Stroke+Y Output Signal 0, 4, 5, N, T - 1 +18 Front Attach. Rear Attach. 1, 2, 3 4, 5, 6 1, 2, 3 +215 +215 4, 5, 6 +228 +228 Stroke (mm) Load & Speed Type (N) A, B, C, D, E 25~150 - 151~200 +2 201~250 +2 251~300 +2 301~350 +12 351~400 +22 401~450 +32 451~500 +42 501~550 +52 551~600 +62 601~650 +72 651~700 +82 701~750 +92 751~800 +102 801~850 +112 851~900 +122 901~950 +132 951~1000 +142 Front Attach. Rear Attach. 1, 2, 3 4, 5, 6 1, 2, 3 +106 +106 4, 5, 6 +119 +119

Rear Attachment (mm) 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, slotless, hole 10.0 4 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 6.4 5 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 8.0 6 = Aluminum, U clevis, slot 6.1, depth 10.5, hole 10.0 Front Attachment (mm) 5 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 8.0 6 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 10.0 4 = Aluminum, U clevis, slot 6.1, depth 16.0, hole 6.4 1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, slotless, hole 10.0 ø6.4 ø10 10.5 6.1 ø6.4 10.5 6.1 10.5 6.1 ø10 ø6.4 ø8 ø10 ø10 6.1 ø6.4 6.1 6.1

Direction of Rear Attachment (Counterclockwise) 1 = 0° 3 = 90° Hole Hole 90º 01 = Tinned leads, core wire 50, stripped wire 10 Connector (mm)

(AWG) Position Feedback P1 Two Micro Switches Cut Off The Actuator at EOS

  • RD 20 EXT+ EXT+ EXT+ EXT+
  • BK 20 RET+ RET+ RET+ RET+
  • RD 26 - V-out +5V +5V
  • ● WH 26 - V-in S1 S1
  • BU 26 - - - S2
  • BK 26 - GND GND GND
  • BN 26 - - - -
  • OG 26 - - - -
  • VT 26 - - - - P1 Two Micro Switches Send Signal at EOS
  • RD 20 EXT+ EXT+ EXT+ EXT+
  • BK 20 RET+ RET+ RET+ RET+
  • RD 26 COM COM +5V +5V
  • ● WH 26 EOS-extended EOS-extended S1 S1
  • BU 26 EOS-retracted EOS-retracted - S2
  • BK 26 - GND GND GND
  • BN 26 - V-in EOS-extended EOS-extended
  • OG 26 - V-out EOS-retracted EOS-retracted
  • VT 26 - - COM COM T-Smart Port Number Wire Color Wire Gauge (AWG) T-Smart P1 ● RD 20 V DC+
  • BK 20 V DC-
  • BN 26 Ctrl EXT
  • GY 26 Ctrl RET
  • OG 26 EOS-extended
  • YE 26 EOS-retracted
  • BK 26 Signal ground
  • ● WH 26 S1/POT/CAN+
  • BU 26 S2/PWM/CAN- P2 Molex 6p socket for TAD1 / Reed switch assembly Wire Definition Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.