M52340SP MITSUBISHI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 44

Technical content

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV)

DESCRIPTION

The M52340SP is a single-chip semiconductor integrated circuit to process signals of a color TV. Circuits to process video IF, sound IF, video, color, and deflection signals, a I C bus control circuit, and D/A are build in this device. This IC can be used not only for popular-type TV sets but also for middle-class TV sets. Combined with a SECAM chroma decoder, the M52325AP, this device can process signals of every type of TVs in the world by discriminating them fully automatically.

FEATURES

  • A built-in I C bus control circuit makes it possible to reduce the number of peripheral parts and rationalize production lines.
  • Various filters (TRAP, BPF, Y-DL, RGB clamp) are build in this IC.
  • PLL detection system is introduced to process video IF and voice IF. Furthermore, AFT coil is not necessary.
  • DL aperture control
  • Color signal frequency and vertical frequency of TVs of every type can be discriminated fully automatically.
  • Horizontal/vertical countdown system
  • V-pulse output
  • RGB output APPLICATION PAL/NTSC system color TV RECOMMENDED OPERATING CONDITION PIN CONFIGURATION (TOP VIEW) Outline 52P4B

52 VIDEO OUT

NC : NO CONNECTION ATT V CC M52340SP AUDIO OUT -(R-Y) IN -(B-Y) IN -(R-Y) OUT SECAM REF. -(B-Y) OUT SYNC SEP IN X-TAL 4.43 V(Y) SW OUT VCD GND TV IN (Y IN) CHROMA APC FILTER KILLER FILTER AUDIO BYPASS X-TAL 3.58 FAST BLK AC-IDENT R IN COINCIDENCE G IN AFT OUT LIMITER IN RF AGC OUT IF AGC FILTER VIF GND VIF IN VIF IN VIF V CC H VCC IIL VCC SCL SCP OUT H OUT H OSC SDA AFC 1 FILTER INTERFACE GND V PULSE OUT AFC 2 FILTER Hi VCC R OUT G OUT B OUT VCD V CC B IN CONTRAST CONT.

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) CUT OFF R G B p MUTE OUT 34 40 43 41 45 16 20515049 524 24 37 39 32 44 12 2835 10 2 4748 3358 CONTRAST RF AGC IF AGC VCO VCO ADJ +- 44 VIF AMP AFT VIDEO DET POS / APC DET ADJ DET DEFEAT VODEO MUTE AFT OUT VIDEO MUTE CLAMP VIDEO TONE DELAY DL TIME DL FINE TRAP SW CHROMA TRAP D.TRAP TRAP HPF 1ST AMP (ACC) CHROMA BPF 2ND AMP REF FILTER SYSTEM ID ID OUT COLOR SERVICE RGB MATRIX CONTRAST CONTRAST CHROMA DEMODULATOR KILLER DET ACC DET ID DET CHROMA APC DET VCXO TINT PHASE CONT F/F PAL SW BRIGHT SYNC SEP BIGP GENE EO ELIMINATE AFC-1 AFC GAIN MUTE DET 32FH VCO 50/60 OUT V SYNC TRIG DRIVE AMP DRIVE R B LAMP HV BLK VERTICAL COUNT DOWIN HORIZONTAL COUNT DOWIN H STOP AFC-2 H-PHASE V.PULSE SERVICE SW SECAM REF B EXT INPUT R EXT INPUT G EXT INPUT LIMITER FM DET 4.5/6.0 ATT BUS I/F AUDIO ATT AF AMP AUDIO MUTE SW NEG SW LOCK DET SYSTEM DECODE SYSTEM SET SYSTEM auto BRIGHT DELAY ADJ VIDEO OUT AFT OUT LIMITER IN RE AGC OUT IF AGC FILTER VIF GND VIF IN VIF VCC H VCC IIL VCC SCL SCP OUT SDA H OSCAFC 1 FILTER INTERFACE GND V PULSE OUT AFC 2 FILTER Hi VCC G OUT R OUT B OUT VCD VCC CONTRAST CONT. B IN G IN R IN COINCIDENCEAC- IDENT FAST BLK AUDIO BYPASS KILLER FILTER CHROMA APC FILTER TV IN (Y IN) VCD GND V(Y) SW OUT X-TAL 4.43 SYNC SEP IN -(B-Y) OUT -(R-Y) OUT SECAM REF. -(R-Y) IN -(B-Y) IN AUDIO OUT ATT VCC FM DIREC T OUT VCO VIDEO APC FILTER BLOCK DIAGRAM X-TAL 3.58 H OUT TV/ EXT p

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Symbol Parameter Ratings Unit VCC Supply voltage 5.0, 8.0 V Pd Power dissipation 1.4 W Topr Operating temperature -20 to 65 ˚C Tstg Storage temperature -40 to 150 ˚C Surge Electrostatic discharge V ABSOLUTE MAXIMUM RATINGS (Ta=25 ˚C, unless otherwise noted) –200 (-150 for only minus side of pin 18)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input pinSG name conditions SW conditionsInput signal UnitMax.Typ.Min. PIN conditions S S S S S Limits S P P P P P S P P P P P P P P P P P P P P P P P P P VCC 1 1 1 11 0 Standard conditions of circuit current Pin 8 current Standard conditions of IF parameters Video detector output DC voltage (NEG) Video detector output DC voltage (POS) Video detector output (NEG) Video detector output (POS) Video S/N Video frequency characteristics Input sensitivity Maximum permissible Input AGC control range 20.0 27.0 33.0 12.0 24.018.0 15.09.0 55.0 21.0 80.0 105.0 2.0 2.4 mA mA mA mA 1.4M M M M M 5V 8V 8V 5V 8V Icc8 Icc9 Icc20 Icc24 Icc47 Maximum IF AGC voltage mA M IF AGC voltage (80dBu) Vdc NEG Vdc POS Vo NEG Vo POS P/N Vf Vin min Vin max GR V4H V V V V V V V M SG1 SG2 SG3 SG4 SG5 V4T SG6 5V 8V 8V 5V 8V M M M M M M SG7 M M 4.8 5.5 2.5 2.5 5.2 2.3 2.2 2.21.9 1.9 2.1 2.5 5550 5.5 4.5 107 102 4.0 2.6 4.4 3.4 4.8 3.0 V V V V dB MHz V V dBm dBm dBm Pin 20 current Pin 24 current Pin 47 current Pin 9 current

ELECTRICAL CHARACTERISTICS

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits S S S S S S S P P P P P P P P P P P P P P P P P P P P P P P P VCC Minimum IF AGC voltage AFT defeat voltage AFT detector sensitivity (NEG) Maximum AFT voltage (NEG) Minimum AFT voltage (NEG) Maximum RF AGC voltage Minimum RF AGC voltage Capture range (U) Intermodulation Sync ratio (NEG) Maximum delay point (NEG/POS) Minimum delay point (NEG/POS) Standard conditions of SIF parameters AF output DC voltage V4L mAFT N V1H N V1L N V3H V3L CRU CRL CRT Capture range (L) Capture range (T) IM DG DG DP DP SPN V V V V V V V V V V V V SG8 SG9 SG10 SG11 SG3 SG3 SG9 SG9 SG12 SG13 SG13 SG13 SW PIN M M M 1.9 2.3 2.7 4.34.03.7 43 61 V V kHz/mV 7.2 0.3 7.7 0.8 V V 7.2 7.7 0.3 0.8 1.20.8 2.2 2.6 3.83.0 31 36 3 7 32.028.525.0 V V MHz MHz MHz dB deg M M M M M M M M DLPH DLPL V V SG14 SG15 M M 90 96 7670 dBm dBm VAF 01 1 1 1 00 5V 8V 8V 5V 8V M 2.82.4 3.2 V SIF block M M ELECTRICAL CHARACTERISTICS (cont.) SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits S S S S S S S P P P P P P P P P P P P P P P P P P P P P P P VCC AF direct output (4.5MHz) Maximum AF output (6.0MHz) Maximum attenuation (6.0MHz) AF output distortion (6.0MHz) Input limiting sensitivity AMR AF S/N Standard conditions of chroma parameters Chroma standard output 1 Chroma standard output 2 ACC characteristics 1 ACC characteristics 2 Overload characteristics Killer operating input level Killer color residual (PAL) VoAF N VoAF P VoAF M VoAF max LIM VoAF S THD AF ATT AMR AFSN S S S S S S S S S SG20 SG17 SG18 SG19 SG18 SG18 SG18 SG18 SG21 M M M M M M M M M M 200 270 340 520410300 320 430 540 550440 610 59 68 1 3 4640 5049 53 63 330 810 1010 mVrms mVrms mVrms mVrms mVrms dB dB dB dB Cn1 ACC1 Cn2 ACC2 OV VikP killP VI SS4P SS4P VS4P VS4P VS4P VS4P VS4P M M M M M M M 1111100 5V 5V 8V8V8V 500 700 900 750600450 -3 0 3 1-1.5-3 -2 0 4 -33-40 30 600 mV P-P mV P-P dB dB dB dB mV P-P SG50 and SG60 should be input to SY IN for C0 to C21 and C13 to C21 respectively.Chroma block (PAL) VI VI VI VI VI VI V=+6dB V=-20dB eb=800mV V=Variable V=-40dB ELECTRICAL CHARACTERISTICS (cont.) AF direct output (5.5MHz) AF direct output (6.0MHz) AF direct output (6.5MHz) P SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits P P P P P P P P P P P P P P P P P P P P Chroma block (NTSC) VikN Killer operating input level (NTSC) killN Killer color residual (NTSC) APC2 APC pull-in range 2 R/BN Demodulated output ratio R-Y/ B-Y R-Y N Demodulated phase angle R-Y TC1 TINT control characteristic 1 TC2 TINT control characteristic 2 SRA SECAM REF output AC voltage SRD SECAM REF output DC voltage VI VI VI VI VS3N VS3N VS3N VS3N VS3N VS3N VS3N M M M M M M M M M -45 -38 03 0 60 –400 –600 0.4 0.6 0.8 80 95 110 25 45 60 25 45 60 180 300 420 4.0 4.5 5.0 dB mV P-P mV P-P Hz ratio deg deg deg V v=Variable eb=0mV f=Variable M eb= Single chroma eb= Single chroma eb= Single chroma eb= Single chroma VI VI VI Test conditions Parameter Input signal SW conditions Limits S S S S S S S

45 VCCSymbol

UnitMax.Typ.Min.P P P P P P P P P P P P P P P P P P P P P P P P APC pull-in range 1 Demodulated output ratio (R-Y / B-Y) Demodulated phase angle R-Y Carrier leak at demodulated output Difference of demodulated output on line Standard chroma output 3 Standard chroma output 4 APC1 CC R/BP DDH Cn3 R-Y P Cn4 VI VS4P VS4P VS4P VS4P 4.2M SS3N SS3N M M M M M M M M M –400 –700 0.60.45 9080 100 0.75 100 100 500 500 900700 600490 mV P-P750 mV P-P mV P-P mV deg ratio Hz VI VI eb= Single chroma f=Variable eb= Single chroma VI VI VI VI SIN ware S S S S S S S ELECTRICAL CHARACTERISTICS (cont.) SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN SW PIN

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits P P P P P P P P P P P P P P P P P P P P P P P P VCC Standard conditions of video and interface parameters Maximum video output Standard video gain Standard double-width amplifier output Video frequency characteristic Chroma trap attenuation 1 Trap fine adj attenuation 1 D. trap attenuation 1 Chroma trap attenuation 2 Trap fine adj attenuation 2 Ymax GY FBY 2AGY CTR1 TRF1 DTR1 CTR2 TRF2 VI VI VI VI VI VI VI VI VI SGA SGA SGA SGB SS3N SS3N SS3N SS4P SS4P SW SW SW SW SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN 1111100 MMM M M MM M MMM M M M M M M M M M M M M 5V 5V 8V8V8V 3.2 3.8 4.2 2.52.1 -4 -2 2.72.11.5 -18 -24 V V dB dB dB 3.2 -18 dB Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits S S S S S S P P P P P P P P P P P P P P P P P P P P AUTO AUTO AUTO AUTO AUTO AUTO System discrimination 1 4.43PAL VI VI VI VI SS4P SS3P SS4N SS3N M M M M M M 150mA 0001 0101 1001 0011 1101 Video and interface block SG50 should be input to SY IN. (SG60 is input for Y5 to Y7 and Y36 to Y46.) System discrimination 2 4.43NTSC System discrimination 3 3.58PAL System discrimination 4 3.58NTSC System discrimination 5 SECAM System discrimination 6 Black and white S S S S S S S S ELECTRICAL CHARACTERISTICS (cont.) VP-P SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN Video frequency characteristic

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Unit Input pinSG name conditions SW conditions PIN conditions UnitS S S S P P P P P P P P P P P P P P P P P P P P P P P VI VI VI VI SS4P SGA SGA SGA SGA SGBVI Contrast control characteristic 1 Video tone control characteristic 1 Video tone control characteristic 2 Video tone control characteristic 3 Video tone control characteristic 4 Video tone control characteristic 5 Contrast control characteristic 2 Brightness control characteristic 1 Brightness control characteristic 2 Brightness control characteristic 3 Drive control characteristic R Drive control characteristic B Test conditions Symbol Parameter Input signal Max.Typ.Min. Limits S S P VCC DTR2 D. trap attenuation 2 VI YDL value 1 YDL value 2 YDL value 3 YDL value 4 EXT (R) I/O characteristic EXT (G) I/O characteristic SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN VI VI VI VI VI VI VI FB ER YDL1 YDL2 YDL3 YDL4 GTnor GTmax GTmin GT2M GT5M GYnor GYmin Lum nor Lum min Lum max D(R) D(B) EX(R) EX(G) SGB SGB SGB SGB f=100kHz SGB SGB SGA SGA SGD SGDFB EG MMM MMM M MMM M M M M M M M M M M M M M M M M M M M M M M M f=100kHz M M M M M M M M M M M M M M M M 5.3 5.7 6.5 6.5 4.8 5.3 3.9 5.7 3.9 4.8 6.4 6.4 -0.7-1-1.3 0.55 0.8 1.05 2.21.8 2.6 2.92.52.1 -4 -1.4 1.2 -2.8 -0.2-5.6 -5-9.3-12.0 6.73.60 1.81.41.0 380 500 620 410300190 270 350 430 220150 -24 dB nsec nsec nsec nsec VP-P dB dB dB dB V P-P mV V V V dB dB VP-P VP-P SW PIN SW PIN SW PIN SW PIN S ELECTRICAL CHARACTERISTICS (cont.)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits S S S S S S P P P P P P P P P P P P P P P P P P P P P P P P VCC SW PIN Color control characteristic 1 Video mute function EXT (B) I/O characteristic Offset voltage between R and G Offset voltage between B and G R cutoff characteristic G cutoff characteristic B cutoff characteristic DL fine delay Color control characteristic 2 Matrix characteristic 1 Matrix characteristic 2 Matrix characteristic 3 Matrix characteristic 4 OSD speed characteristic 1 OSD speed characteristic 2 Contrast control characteristic 3 Contrast control characteristic 4 SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN EX(B) OFRG FB EB SGD OFBG C(R) C(G) C(B) Coon DLF Coon VMF MTXB MTXG MTXR MTXG1 OSD1 OSD2 GYnor GYmin ABR VI VI ER.EG EB.FB Additonai brightness voltage ER.EG EB.FB VI VI SGA SGA SGA SGE SGA SGE SGE SGE SGD SGD SGA SGA VP-P mV 6.55.75.3 160-160 -20 MM M V mV V V nsec mV P-P mV P-P dB VP-P mV P-P VP-P mV P-P nsec nsec VP-P mV P-P V2.0 05 0 3.52.71.7 16050 9020 500 600300 1.1 1.7 1.9 330 430180 1.1 1.7 1.9 -50 -40 10 150 870730610 20 45 70 2.4 2.4 2.42.1 2.1 2.11.8 1.8 1.8 160-160 40MM M M M M M M MM M MM M M M M MMM M M M M MM M MM M M M MM S 2.9V 8.5V ELECTRICAL CHARACTERISTICS (cont.)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions UnitMax.Typ.Min. Limits S S S S S S S P P P P P P P P P P P P P P P P P P P P P P P VCC DEF block Standard conditions of sync deflection parameters Sync separation input sensitivity current BGP timing 1 BGP timing 2 BGP pulse width Horizontal free running frequency Horizontal pulse width Horizontal pull-in range 1 Horizontal pull-in range 2 Horizontal pulse timing 1 Horizontal pulse timing 2 Horizontal pulse timing 3 Horizontal pulse amplitude Horizontal stop operation AFC gain operation Vertical free running frequency Minimum vertical output voltage Minimum coincidence detection voltage Service switch operation BGP1 BGP2 BGPW ISS fH FPH1 FPH2 FPT1 FPT3 FPT2 TH VH HSTO AFCG fV VVL CoinL SW SY SY SY SY SY SY SY SY SY SGa SGb SGa SGc f Variable SGc f Variable SGa SGa SGa SGa M M M M M M M M M M M M M M M M 1111 000 5V 5V 8V8V8V M M M M M 0.1 0.2 2.82.01.2 1.4 2.2 3.0 7.264.8 15.3 15.7 16.1 +300+250 -300 8.5 9.57.5 -2.0 -1.5 -1.0 1.51.0 2.8 5.4 8.9 474441 0 0.3 0.7 0 0.5 1.5 Hz V V V V dB Hz kHz mA msec msec Hz msec msec msec msec msec29 2.0 V43 M M M P M ELECTRICAL CHARACTERISTICS (cont.) -250 6.7 SW PIN SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) Test conditions Symbol Parameter Input signal Input pinSG name conditions SW conditions PIN conditions Unit Max.Typ.Min. Limits S S S S S S P P P P P P P P P P P P P P P P P P P P P P P P VCC Vertical pull-in range Vertical output pulse width Vertical BLK width 50/60 confirmation 1 50/60 confirmation 2 50/60 confirmation 3 50/60 confirmation 4 Minimum sync detection width f60Hz width:variable Hz65 msec msec Hz Hz Hz Hz msec 1.6 0.35 0.650.52 1.51.35 13M MMM M M FPV VW VBLKW AVER1 AVER2 AVER3 AVER4 WVSS SY SGd f Variable SGd f63Hz SGd f57Hz SGd f53Hz SGd f47Hz SGd SY SY SY SY SY SW SW SW SW SW SW SW SW PIN PIN PIN PIN PIN PIN PIN PIN S ELECTRICAL CHARACTERISTICS (cont.)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HSTSymbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data A6 A6 A6 A6 A6 A6 A8 A8 A8 A0 A0A0 A7 A7 A7 C2 20000003 2 3 2 3 2 3 2 3 2 3 264 64 8 00 0 0 00128 128 128 ELECTRICAL CHARACTERISTICS (cont.) TINT ATT A6A6 032032 Icc9 Icc20 Icc24 Icc47 Vdc NEG Vdc POS Vo POS Vo NEG P/N Vin min Vf Vin max GR V4H V4T V4L VIF block Icc8

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data ELECTRICAL CHARACTERISTICS (cont.) TINTATT Function Data mAFT N V1H N V1L N V3H CRU V3L CRL CRT IM DG DP SPN DLPH DLPL VAF VoAF N VoAF p VoAF S VoAF M SIF blcok

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data A6 A6 A6 A6 A6 A6 A8 A8 A8 A0 A0A0 A7 A7 A7C2 2000000 3 23 2 3 2 3 2 3 23 264 64 8 0 0 0 000128 128 128 ELECTRICAL CHARACTERISTICS (cont.) TINT ATT A6A6 032032 Function Data Function Data AFSN Cn1 Cn2 R/BP CC DDH VikP VoAF max ATT LIM AMR THD AF ACC1 R-Y P ACC2 OV killP APC1 Chroma block (PAL) 001 127

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data A6 A6 A6 A6 A6 A6 A8 A8 A8 A0 A0A0 A7 A7 A7A3 0000000 3 23 2 3 2 3 2 3 23 264 64 8 0 0 0 000128 128 128 ELECTRICAL CHARACTERISTICS (cont.) TINT ATT A6A6 032032 Function Data Function Data TC1 AUTO AUTO SRD AUTO AUTO Cn3 Cn4 TC2 SRA AUTO AUTO VikN killN R/BN APC2 R-Y N Chroma block (NTSC) 127

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data A6 A7 A0 A5 A5 A5 A0 A0A2 A0 A6 A7 A3 01010003 2 6 4 0 16 16 1603 2 80 0 00 0 0 ELECTRICAL CHARACTERISTICS (cont.) TINT ATT A6A6 032032 Function Data Function Data 127 TRF1 DTR1 CTR2 TRF2 GTmax GT2M GT5M YDL3 Ymax GY 2AGY CTR1 FBY DTR2 GTmin YDL1 YDL2 YDL4 GTnor A0/A6 A0/A6 Video and interface blockSG50 should be input to SY IN. (SG60 is input for Y5 to Y7 and Y36 to Y46.)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data ELECTRICAL CHARACTERISTICS (cont.) TINTATT Function Data Function Data 127 GYnor GYmin Lum nor Lum max Lum min D(R) D(B) EX(R) EX(G) EX(B) OFRG OFBG C(R) C(G) C(B) DLF Coon Coon VMF MTXB A6 015 1 127 127 127 127 A0/B9 A0/B9 A0/C1 A0/C1 A0/C1 A0/A4

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Function Data Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data ELECTRICAL CHARACTERISTICS (cont.) TINTATT Function Data Function Data 127 127 A6 A7 A0 A7 A6 OSD1 GYnor BGP1 FPH1 HPT1 MTXG MTXR MTXG1 OSD2 GYmin ABR ISS BGP2 BGPW fH FPH2 HPT2 HPT3 032 0 0 0 63 0 32 0 127 128 128 128 000 000 128 128 128 DEF block

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) AFCG Function Data Data 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 13H DLA P/N VCOA AUDM 45/60 TRAP DBF DFA SHARP DEFE CONT DLTA TV/EXTAUTO COLOR SET HP BRI DR MUTE DB CR CG CB TRF SESW HST Symbol Sub address Function Function Function Function Function Function Function Function Function Function Function Function Function Function Data Data Data Data Data Data Data Data Data Data Data Data ELECTRICAL CHARACTERISTICS (cont.) TINTATT Function Data Function Data TH VH HSTO AFCG fV VVL CoinL SW FPV VW VBLKW AVER1 AVER2 AVER3 AVER4 WVSS A0/A6

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) 1. Input SG3 and measure the rms value of output signal a pin 52. 2. P/N is defined as follows: P/N = 20 log P/N Video S/N 1. Input SS4P to VI IN. 2. Measure output amplitude, Cn1 and Cn2, at pins 41 and 43 respectively. Decrease the input level of SG18. Measure the input level when the element of 400Hz at pin 46 is 3dB smaller than V0AFM (S6:Maximum AF output (6.0M)). 1. Measure the element of 400Hz of output at pin 46. 2. ATT is defined as follows: ATT = 20 log mAFTN is defined as follows: mAFTN= VONEG Measured Value(VP-P)X10 Measured Value(mVrms) (dB) 1. Input SG4 and set the frequency f2 to 37.9MHz so that the beat element of 1MHz is output to pin 52. 2. Then set the applied voltage at pin 4 so that the beat element of 1MHz at pin 52 may be 100dBm. 3. Decrease f2 to the level at which the beat element becomes 3dB smaller than the element of 1MHz, and read the value at that level. BW Video frequency characteristics 1. Input 90dBu SG6. 2. VA is the output level at pin 52. Increase SG6 voltage until the output at pin 52 becomes 3dB smaller than VA. The input level at that time is the maximum permissible input. Vin max. Maximum permissible input Vin min. Input sensitivity 1. Decrease SG5 level until the video detector output is 3dB smaller than the measured value of Parameter V3 "Video detector output". mAFTN AFT detector sensitivity (NEG) V1HN Maximum AFT voltage (NEG) V1LN Minimum AFT voltage (NEG) See the following figure. V1HN V1LN D f 5.0V 3.0V 37.9MHz 39.9MHzf0 f (5.0-3.0)X10 mV D f KHz (mV/KHz) 1. Adjust the applied voltage at pin 4 so that the lowest output signal voltage at pin 52 is 2.2V. IM Intermodulation 2.2V P52 2. Measure elements of 1.07MHz and 4.43MHz of output at pin 52. 3. IM is defined as follows: IM = 20 logElement of 1.07MHz Element of 4.43MHz (dB) ATT Maximum attenuation V0AFmax Measured value(dB) LIM Input limiting sensitivity AMR AMR 1. Vam is the element of 400Hz at pin 46. 2. AMR is defined as follows: AMR = 20 logV0AFS (mVrms) Vam (mVrms) (dB) 1. Measure the noise (20Hz to 100KHz) of output at pin 46. 2. AF S/N is defined as follows: AF S/N = 20 log AF S/N AF S/N V0AFmax Measured value(dB) Cn1 Standard chroma output 1 (PAL) Cn2 Standard chroma output 2 (PAL) ACC1 ACC characteristics 1 1. Input VS4P (eb=570mV:level+6dB) to VI IN. 2. Measure the output amplitude at pin 41. 3. ACC1 is defined as follows: ACC1 = 20 logMeasured value (V P-P) Cn1 (VP-P) (dB) ACC2 ACC characteristics 2 1. Input VS4P (input level:-20dB) to VI IN. 2. Measure the output amplitude at pin 41. 3. ACC2 is defined as follows: ACC2 = 20 logMeasured value (V P-P) Cn1 (VP-P) (dB) ELECTRICAL CHARACTERISTICS TEST METHOD 3dB 1MHz 100dBmP52 BW

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) OL Overload characteristics 1. Input VS4P (ec=800mVP-P:chroma+3dB) to VI IN. 2. Measure the output amplitude at pin 41. 3. OL is defined as follows: OL = 20 log Measured value (V P-P) Cn1 (VP-P) (dB) 1. Input SS3N to VI IN 2. Cn3 and Cn4 are output amplitude measured at pins 41 and 43 respectively. Cn3,Cn4 Standard chroma output 3,4 (NTSC) 1. Input VS3N (eb=single chroma=ec+50KHz) to VI IN. 2. V41 is the output amplitude at pin 41. 3. V43 is the output amplitude at pin 43. 4. R-Y/B-YN is defined as follows: R-Y/B-YN = 20 log R-Y/B-YN Demodulated output ratio V43(V P-P) V41(VP-P) (dB) 1. Input VS4P (level:variable) to VI IN at input level 0dB. 2. Lower the input level with monitoring the output amplitude at pin 41 and measure the input level when output amplitude is not found. VikP Killer operating input level (PAL) 1. Input VS4P (level:-40dB) to VI IN. 2. Measure the output amplitude at pin 41. KillP Killer color residual (PAL) 1. Input VS4P (f=eb=ec=variable) to VI IN. 2. Change the input signal frequency and measure the frequency range from the point at which signal is output to pin 41 and to the point that no signal is output to the pin. The reference value is 4.433619MHz. APC1 APC pull-in range 1 1. Input VS4P (eb=single chroma=ec+50KHz) to VI IN. 2. V41 is the output amplitude at pin 41. 3. V43 is the output amplitude at pin 43. 4. R-Y/B-YP is defined as follows: R-Y/B-YP = 20 logV43 (V P-P) V41 (VP-P) (dB) R-Y/B-YP Demodulation output ratio 1. Input VS4P (eb=single chroma=ec+50KHz) to VI IN. 2. V41 is the output amplitude at pin 41. 3. V43 is the output amplitude at pin 43. 4. R-YP is defined as follows: q R-YP = tan * Vector should be found with taking the gain ratio of a demodulator into consideration. V43 X3.8 (V41X1.9)+45° (deg) R-YP Demodulated phase angle Measure the element of 4.43MHz of the demodulated output in no-input state. CC Demodulated output carrier leak 1. Input 4.2MHZ CW (Vi=575mVP-P) to VI IN. 2. Measure the center DC voltage of output beat amplitude for two lines at pins 41 and 43. The absolute value of the difference in DC voltage is the difference of demodulated output on line. DDH Difference of demodulated output on line 1H 2H GND 1. Input VS3N (level:variable) to VI IN at input level 0dB. 2. Lower the input level with monitoring the output amplitude at pin 41 and measure the input level when output amplitude is not found. VikN Killer operating input level (NTSC) 1. Input VS3N (level:-40dB) to VI IN. 2. Measure the output amplitude at pin 41. KillN Killer color residual (NTSC) 1. Input VS3N (f=eb=ec=variable) to VI IN. 2. Change the input signal frequency and measure the frequency range from the point at which no signal is output to pin 41 and to the point at which signal is output to the pin. (Pull-in state) The reference value is 3.579545MHz. APC2 APC pull-in range 2 1. Input VS3N (eb=single chroma=ec+50KHz) to VI IN. 2. V41 is the output amplitude at pin 41. 3. V43 is the output amplitude at pin 43. 4. R-YN is defined as follows: q R-YP= tan * Vector should be found with taking the gain ratio into consideration. q R-YN Demodulated phase angle V43 X3.8 (V41X1.9)+45° (deg) MM

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) TC1 Tint control characteristics 1 TC2 Tint control characteristics 2 1. Input VS3N (see the following figure) to VI IN. Based on the output voltage at pin 41, find the absolute angle as shown in the above figure. -180° 0° 90° A B GND 90° A B q = tan (B/A) 2. Tint data center (63) is defined as the reference angle (TC). Find angles at tint data max. and tint data min. TC1 and TC2 are differences in angle between TCMAX and TC and between TCMIN and TC and defined as follows. TC1 = TCMAX-TC (deg) TC2 = TC-TCMIN (deg) SRA SECAM REF output AC voltage SRD SECAM REF output DC voltage Measure the amplitude (SRA) and DC voltage (SRD) of the element of 4.43MHz of output at pin 42. AUTO 1 to 6 System confirmation 1 to 6 Set to AUTO mode and confirm that bus for each output signal is read correctly. Ymax Maximum video output 1. Input SGA to VI IN 2. Measure the amplitude ( P-P) except that at blanking part of output at pins 21,22 and 23. M GY Video Standard video output 1. Input SGA to VI IN 2. Measure the amplitude (P-P) except that at blanking part of output at pins 21,22 and 23.This amplitude is defined as G1. M = G1 3. GY is defined as follows: GY = 20 log (G1VP-P/0.714VP-P) (dB) BW Video frequency characteristics 1. Input SGB (5MHz, 0.4VP-P) to VI IN. 2. Measure the amplitude (P-P) except that at blanking part of the output at pin 22 .The amplitude is defined as YB. 3. BW is defined as follows: BW = 20 log (YB VP-P/GY VP-P) (dB) 2AGY Standard double-width amplifier output 1. Input SGA to VI IN. 2. Measure the amplitude (P-P) except that at blanking part of output at pin 22. CTR1 Chroma trap attenuation 1 (common to R/G/B output) 1. Input SS3N to VI IN. Measure the frequency level of 3.58MHz at trap data 0. The level is defined as N0. 2. Then, measure the level at trap data 1. 3. CTR1 is defined as follows. CRT1 = 20 logMeasured value (mV P-P) N 0 (mV P-P) (dB) TRF1 Trap fine adj. attenuation 1 (common to R/G/B output) 1. Input SS3N to VI IN. 2. Measure the output amplitude of the element of 3.58MHz when trap fine adj. switch is on. (TRFon) 3. TRF1 is defined as follows. TRF1 = 20 logTRFon (mV P-P) N 0 (mV P-P) (dB) DTR1 D. trap attenuation 1 (common to R/G/B output) 1. Input SS3N to VI IN. 2. Measure the output amplitude of the element of 3.58MHz when D. trap switch is on. (DTRon) 3. DTR1 is defined as follows. DTR1 = 20 logDTRon (mV P-P) N 0 (mV P-P) (dB) CTR2 Chroma trap attenuation 2 (common to R/G/B output) 1. Input SS4P to VI IN and measure the frequency level of 4.43MHz at trap data 0. The level is defined as P0. 2. Then, measure the level at trap data 1. 3. CTR2 is defined as follows. CTR2 = 20 logMeasured value (mV P-P) P0 (mV P-P) (dB) TRF2 Trap fine adj. attenuation 2 1. Input SS4P to VI IN. 2. Measure the output amplitude of the element of 4.43MHz when trap fine adj. switch is on. (TRFon) 3. TRF2 is defined as follows. TRF2 = 20 logTRFon (mV P-P) P0 (mV P-P) (dB)

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DTR2 D. trap attenuation 2 1. Input SS4P to VI IN. 2. Measure the output amplitude of the element of 4.43MHz when D. trap switch is on. (DTRon) 3. DTR2 is defined as follows. DTR2 = 20 log Note: In parameters Y5, Y6, Y8 and Y9, limits are defined based on the maximum attenuation by comparing each one. DTRon (mV P-P) P0 (mV P-P) (dB) YDL1 YDL value 1 1. Input SGA to VI IN. 2. Measure the delay time from signal input to output at pins 21, 22 and 23. M SGA Output signal Measure the delay time at the center point of rise. YDL2, 3 and 4 YDL value 2, 3 and 4. 1. Input SGA to VI IN. 2. Measure the delay time from signal output at pins 21, 22 and 23 to YDL1. GTnor Video tone 1 1. Input SGB (f=3MHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. GTmax Video tone 2 1. Input SGB (f=3MHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. 3. GTmax is defined as follows: GTmax = 20 logMeasured value (V P-P) GTnor (VP-P) (dB) GTmin Video tone 3 1. Input SGB (f=3MHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. 3. GTmin is defined as follows: GTmin = 20 logMeasured value (V P-P) GTnor (VP-P) (dB) GT2M Video tone 4 1. Input SGB (f=2MHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. 3. GT2M is defined as follows: GT2M = 20 logMeasured value (V P-P) GTnor (VP-P) (dB) GT5M Video tone 5 1. Input SGB (f=5MHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. 3. GT5M is defined as follows: GT5M = 20 logMeasured value (V P-P) GTnor (VP-P) (dB) GYnor Contrast characteristics 1 1. Input SGB (f=100KHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. GYmin Contrast characteristics 2 1. Input SGB (f=100KHz) to VI IN. 2. Measure output amplitude at pins 21, 22 and 23. 3. GYmin is defined as follows: GYmin = 20 logMeasured value (V P-P) GYnor (VP-P) (dB) Lum nor Brightness control characteristics 1 Lum max Brightness control characteristics 2 Lum min Brightness control characteristics 3 1. No signal is input. (Only SG50 is input to SY IN.) 2. Measure DC voltage of output at pins 21, 22 and 23 except that at blanking part. M GND Output waveform D(R) Drive control characteristics R 1. Input SGA to VI IN. 2. Measure DRmin and DRmax which are output amplitude at pin 21 at D(R) data min and D(R) data max respectively. 3. D(R) is defined as follows: D(R) = 20 logDRmax(V P-P) DRmin (VP-P) (dB) D(B) Drive control characteristics B 1. Input SGA to VI IN. 2. Measure DBmin and DBmax which are output amplitude at pin 23 at D(B) data min and D(B) data max respectively. 3. D(B) is defined as follows: D(B) = 20 logDBmax(V P-P) DBmin (VP-P) (dB) EXR EXT(R) I/O characteristics EXG EXT(G) I/O characteristics EXB EXT(B) I/O characteristics 1. Input SGD to FB, ER, EG and EB. 2. Measure output amplitude which is higher than the pedestal level at pins 21, 22 and 23. The amplitude at blanking part should not be measured. M

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) OFRG Offset voltage between R and G OFBG Offset voltage between B and G 1. Measure DC voltage of output at pins 21,22 and 23 except that at blanking part. 2. OFRG and OFBG are defines as follows: OFRG = (pin 21 Measured voltege)-(pin 22. Measured voltege) (mV) OFBG = (pin 23 Measured voltege)-(pin 22 Measured voltege) (mV) R(C) R cutoff characteristics G(C) G cutoff characteristics B(C) B cutoff characteristics 1. Measure DC voltage of output at pins 21,22 and 23 when R(C), G(C) and B(C) data are maximum and minimum respectively. The DC voltage at blanking part should be measured. 2. R(C), G(C) and B(C) are defined as follows: R(C), G(C), and B(C) = (Voltage at data max.) - (Voltage at data min.) (V) DLF DL fine delay 1. Input SGA to VI IN. 2. Measure the time lag (absolute value) between signal YDL4 and output signal at pins 21,22 and 23. M Y14 YDL4 signal Output signal Measure the time lag at the center point of rise. Ccon1 Color control characteristics 1 1. Input SGE to -R IN (pin 45). 2. Measure output amplitude at pins 21,22 and 23 under each condition. Ccon2 Color control characteristics 2 1. Input SGF to VI IN. 2. Measure output amplitude of the element of 4.43MHz when the mute switch is on and off. (VMFon, VMFoff) 3. VMF is defined as follows: VMF = 20 log VMF Video mute characteristics TRFon (VP-P) TRFoff (VP-P) (dB) 1. Input SGE to -B IN (pin 44). 2. Measure output amplitude at pins 22 and 23. (P23 = MTXB, P22 = MTXG) MTXB Matrix characteristics 1 MTXG Matrix characteristics 2 1. Input SGE to -R IN (pin 45). 2. Measure output amplitude at pins 21 and 22. (P21 = MTXR, P22 = MTXG1) MTXR Matrix characteristics 3 MTXG1 Matrix characteristics 4 1. Input SGD to FB, ER, EG and EB. 2. Measure rise time and fall time of the signal of output at pins 21,22 and 23. Measurement points should be higher than the pedestal level and blanking part should not be measured. OSD1 OSD speed characteristics 1 OSD2 OSD speed characteristics 2 MM OSD1 OSD2 10% 90% Output waveform at pins 21,22 and 23. 1. Input SGA to VI IN. 2. Measure output amplitude at pins 21,22 and 23 when 2.9V and 0V are externally applied to pin 26. GYmax1 Contrast control characteristics 3 GYmin1 Contrast control characteristics 4 Make current flow out from pin 40 and measure the flow current when the burst gate pulse is not found at pin 12. ISS Sync separation input sensitivity current BGP2 BGP timing 2 BGPW BGP pulse width BGP1 BGP timing 1 BGP1,BGP2 BGPW P40 SYNC P12 SCP Measure the output frequency at pin 13 when no signal is input. FH Horizontal free run frequency FPH1 Horizontal pull-in range 1 FPH2 Horizontal pull-in range 2 Change the frequency of SGc and measure the frequency at the moment when the output signal at pin 13 and the input signal at pin 40 are pulled in. The horizontal pull-in range is measured by comparing with the horizontal free run frequency. HPT2 Horizontal pulse timing 2 HPT3 Horizontal pulse timing 3 HPT1 Horizontal pulse timing 1 HPT1, HPT2, HPT3 P40 SYNC P13 H OUT

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) VH Horizontal pulse amplitude TH Horizontal pulse width VH TH P13 H OUT HSTO Horizontal stop operation Confirm that the horizontal output is high when the horizontal stop switch is on. 1. Measure AFCon which is the output amplitude of pin 16 when AFC switch is on and AFCoff which is that when the switch is off. 2. AFCG is defined as follows: AFCG = 20 log AFCG AFG gain operation AFCon (VP-P) AFCoff (VP-P) (dB) FV Vertical free run frequency Measure the output frequency at pin 18 when no signal is input. VVL Minimum vertical output voltage CoinL Minimum coincidence detection voltage Measure the output DC voltage at pin 28 when no signal is input. M GND P18 V. PULSE SW Service SW operation Measure the output DC voltage at pin 18 when the service switch is on. FPV Vertical pull-in range Confirm that the frequency of output at pin 18 is the same at each input frequency (pull-in state). Also, confirm the state of the bus write mode (D7). VVL Vertical pulse width M GND P18 V. PULSE VBLKW Vertical BLK width M Output waveform at pins 21, 22 and 23 GND AVER1 50/60 confirmation 1 AVER2 50/60 confirmation 2 AVER3 50/60 confirmation 3 AVER4 50/60 confirmation 4 Reduce the width of signal SGd and measure the width of input signal when the output waveform at pin 18 disappears. WVSS Minimum sync detection width Decrease the frequency of SGd and measure the frequency when output waveform at pin 18 is pulled in.

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) INPUT SIGNAL SG. No. SG. 1 SG. 2 SG. 3 SG. 4 SG. 5 SG. 6 SG. 7 SG. 8 SG. 9 SG. 10 SG. 11 SG. 12 SG. 13 SG. 14 SG. 15 SG. 16 SG. 17 SG. 18 SG. 19 SG. 20 SG. 21 Input signal (Value at pin terminal is 50W ) VIF/SIF f 0 = 38.9MHz, 90dBm, fm = 20KHz, AM77.8% f0 = 38.9MHz, 90dBm, fm = 50KHz, AM77.8% f0 = 38.9MHz, 80dBm, CW f1 = 45.75MHz, 90dBm, CW f2 = 44–5MHz, 90dBm, CW Mixed signal f0 = 38.9MHz, Variable, fm = 20KHz, AM77.8% f0 = 38.9MHz, fm = 20KHz, AM16%, Level variable f0 = 38.9MHz, 80dBm, CW f0 = 38.9MHz, 110dBm, CW f0 = 38.9 –5MHz, 90dBm, CW f0 = 37.9MHz, 90dBm, CW f0 = 39.9MHz, 90dBm, CW f1 = 38.9MHz, 90dBm, CW f2 = 34.47MHz, 80dBm, CW f3 = 33.4MHz, 80dBm, CW Mixed signal f0 = 38.9MHz, Standard 10-step modulation, Sync ratio:28.6%, AM = 87.5% video modulation, Sync chip level 90dBm f0 = 38.9MHz, 93dBm, CW f0 = 38.9MHz, 73dBm, CW f0 = 4.5MHz, 100dBm, fm = 400Hz, FM–25KHz dev f0 = 5.5MHz, 100dBm, fm = 400Hz, FM–50KHz dev f0 = 6.0MHz, 100dBm, fm = 400Hz, FM–50KHz dev f0 = 6.5MHz, 100dBm, fm = 400Hz, FM–50KHz dev f0 = 6.0MHz, 100dBm, fm = 400Hz, AM30% f0 = 6.0MHz, 100dBm, CW Note 1: The timing and pulse width of the horizontal blanking pulse should be as shown in the following figure by adjusting the variable resistor of the single shot multi vibrator. Pin13 Horizontal output Horizontal blanking pulse 8ms 12ms The variable resistor at pin 15 of the TTL IC, M74LS221P, is used to fix the timing at 8ms and that at pin 7 is used to fix the pulse width at 12ms. Coil adjustment VCO coil 1. Set the test conditions as shown in the parameter V14. 2. Input CW (f0=38.9MHz, Vi=90dBm) to input pin A. 3. Set the DC voltage at pin 1 (AFT OUT) to 1/2VCC (4.0V) by adjusting VCO coil. Voltage 38.9MHz 4.0V Frequency Pin 1 Output waveform Note) VCO coil should always be adjusted as above before using this IC.

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) INPUT SIGNAL PARAMETERS INCLUDING INPUT SIGNALS 1. Input signal name is four alphanumeric characters. Ex.) S S 4 P Standard Signal 4.43MHz PAL system Fourth character Third character Second character First character First character: Standard=S, Nonstandard=V (Modified parts should be specified.) Second character: Meaning of signal Third character: Frequency of burst and chroma 4(4.433619MHz), 3(3.579545MHz) (In case of "S", SECAM standard signal is applied.) Fourth character: Color system N(NTSC), P(PAL) 2. Structure of input color signal The following figure shows the structure of color signal. ec eb eb(n) ec(n) eb(n+1) ec(n+1) H.sync 500mV P-P 1. When S (standard) is used as the first character, the standard color bar signal of each system is applied. H.sync should be added for input clamp. (The frequency of H.sync is fixed according to the fourth character. P:50Hz, N:60Hz) 2. Amplitude and frequency of burst are represented as eb. In case of standard signal, the amplitude is 285mV P-P and the frequency is shown by the third character. 3. Amplitude and frequency of chroma are represented as ec. In case of standard signal, the amplitude is 570mVP-P and the frequency is shown by the third character. 4. The following figure shows the phase of a PAL system signal. ec(n) ec(n+1) eb(n+1) eb(n) R-Y B-Y

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) VIDEO/INTERFACE SG. No. SG. A Input signal (Value at pin terminal is 50W ) PAL system PAL system APL 100% standard video signal should be input as sync separation input as shown in the figure. The vertical signal should be interlaced at 50Hz. 5ms 2ms7 ms 1VP-P 0.714VP-P 0.286VP-P SG. B The frequency and amplitude of signal Lumi can be changed by signal SGA. The typical amplitude is 0.714mV P-P. 5ms 2ms7 ms SG. C Level:variable 4ms 20m Sync 20m24m 0.7V 0VSG. D f = 100kHz 0.5V Level:variable typ = 0.3VP-P H = 15.625KHz, V = 50Hz SG. E SG. 50 Standard PAL SYNC 5ms 1VP-P 0.714VP-P 0.286VP-P f = 3.58MHz 63.5ms Level:variable typ = 0.3VP-P H = 15.734KHz, V = 60Hz Standard NTSC SYNC NTSC system SG. F SG. 60

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DEFLECTION SG. No. SG. a Input signal (Value at pin terminal is 50W ) The input signal should be PAL system APL-variable video signal. Vertical signal should be interlaced at 50Hz. 5ms 2ms7 ms 0.714VP-P 0.286VP-P SG. b SG. c SG. d Duty 90% Frequency:variable Level:variable (Typ. : 1VP-P) 64ms Pedestal The input signal should be NTSC APL-variable video signal. Vertical signal should be interlaced at 60Hz. 5ms 2ms7 ms 0.714VP-P 0.286VP-P 63.5ms Pedestal 1VP-P Duty 95% Frequency:variable Level:variable (Typ. : 1VP-P) Duty : variable (Typ. : 95%) 1VP-P

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) P21 -B IN P28 P26 P23P22P18 P16 P12 P13 8 7 6 5 4 3 2 1 9 10 15141312 1611 0.01u P46 P43 8 7 6 5 4 3 2 15149 10 11 12 13 16 P38P40P41 8 7 6 5 4 3 2 1 9 10 11 15141312 16 P36 1 3 4 6 52 48 47 46 45 44 43 42 41 40 39 38 37 36 5 7 8 9 10 11 12 13 14 15 16 17 35 34 33 32 30 29 28 18 19 20 21 23 24 25 26 P3 P4 A P48 50 49 P52 A AA 0.01u SIN 620 10k M74L221P 4700p VR 20k 2200p VR 20k +5V 5.1k 0.01u 47u 270k AFT OUT RF AGC OUT 0.1u 0.22u VIN 1646 0.01u 47u 510 12k S16 10u 6.8k 0.01u GND VCC Hi VCC GND FBP IN H.OUT B503F18 SDA SCL 2.7kV.PULSE OUT 680k 0.01u 47u R G B 3.6k 3.6k 3.6k EB IN EXT B IN 0.01u 47u 0.1u cont. Hi VCC VCC VCC 2.2uH 0.47u DIRECT OUT VIDEO OUT AUDIO OUT S45 S44 01 1 75-R IN 10k 10u VI IN U3660M0.01u 0.01u 0.01u 0.01u 1800p 220 12P 4.3M X_TAL 15p 330k Sync OUT Y IN 0.22u 1u3.3k 0.015u 1.8M2.2u 10u 100p 3.58M X_TAL 0.22u 300k EXT R IN 0.1u 0.022u 680k 0.1uEXT G IN EG IN Hi VCC VCC ER INFB IN 75S3 S40 0.01u 0.1u M52325AP 0.22u 0.1u SY IN 0.01u 270k M52340SP S.S IN GND 0.01u Units Resistance : W Capacitance : F TEST CIRCUIT

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) 1.5 1.0 0.5 250 50 75 125 THERMAL DERATING (MAXIMUM RATING) POWER DISSIPATION P d (mW) AMBIENT TEMPERATURE Ta (˚C) TYPICAL CHARACTERISTICS 100 150 1.4

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) MUTE OUT 14 132841 45 1644 124339 323724353034 4036 D.TRAP TRAP CUT OFF R G B APPLICATION EXAMPLE 20515049 524 6 187 3 13 12 9 1016 111416 12 1 9 3 4 8 10 5 10 2 4748 3358 RF AGC OUT (REV) VIF IN RF AGC F AGC VCOVCO ADJ +- 4 VIF AMP AFT VIDEO DET POS / APC DET ADJ DET DEFEAT VODEO MUTE AFT OUT VIDEO MUTE CLAMP VIDEO TONE DELAY DL TIME DL FI NE TRAP SW CHROMA TRAP SV 1VP-P TV IN 2V P-P HPF 1ST AMP (ACC) VHROMA BPF 2ND AMP REF FILTER SYSTEM ID ID OUT COLOR SERVICE RGB MATRIX CONTRAST CONTRAST CHROMA DEMODULATOR KILLER DET ACC DET ID DET CHROMA APC DET VCXO 4.43 3.58 VIDEO CHROMA VCC SECAM M52325AP 1H DL VCC F.B.P SCP -(B-Y) IN -(R-Y) IN -(R-Y) OUT -(B-Y) OUT TINT PHASE CONT F/F PAL SW BRIGHT SYNC SEP BIGP GENE EO ELIMINATE AFC-1 AFC GAIN MUTE MUTE DET 32FH VCO 50/60 OUT V SYNC TRIG DRIVE AMP DRIVE R B LAMP HV BLK VERTICAL COUNT DOWIN HORIZONTAL COUNT DOWIN H STOP AFC-2 H-PHASE H. OUTPUT V.PULSE SERVICE SW SECAM REF B EXT INPUT R EXT INPUT G EXT INPUT LIMITER FM DET 4.5/6.0 ATT VCC ATT BUS I/F AUDIO ATT AF AMP AUDIO POWER SDA SCL FAST BLK B IN R IN R B G G IN SECAM REF HV CC DEFLECTION VCC V.PULSE OUT PUT AUDIO MUTE SW DIRECT OUTGND VCC VIF / SIF HI VCC IL VCC 2VP-PVIDEO OUT 2.2VP-P NEG SW LOCK DET SYSTEM DECODE SYSTEM SETSYSTEM auto p BRIGHT DELAY ADJ CONTRAST p

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN RE AGC OUT IF AGC FILTER Pin No. Name Description Peripheral circuit of pin DC voltage AFT OUT VIF GND LIMITER IN 4.0V 5.6k 100 20p 30k 10p 3.0V 7.5V to 0.5V 4.5V to 2.5V

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) H VCC IIL VCC Pin No. Name Description Peripheral circuit of pin DC voltage VIF IN SCL VIF VCC 1.5V Power supply for VIF Power supply for all circuits in the deflection block Power supply for I2C bus IIL I2C bus clock input 5.0V 8.0V 1.5V to 1.2k 51.6k V

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) to to DESCRIPTION OF PIN (cont.) Pin No. Name Description Peripheral circuit of pin DC voltage SCP OUT AFC 1 FILTER H OUT MAX 4mA Horizontal frequency pulse output Sandcastle pulse output 5.5V 200 200 H OSC14 3.1VCSB-503 F18 is used. to SDA15 I2C bus data input 40k 48k X24 600 300 300 10k 80k51.6k V

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) AFC 2 FILTER Hi VCC Pin No. Name Description Peripheral circuit of pin DC voltage GND G OUT V pulse B OUT R OUT MAX 4mA Primary-color (R, G and B) signal output pin

24 VCD V CC Power supply for video

2.5V 2.9V TYP 150 X120 PIN PIN 2.0k X135 Power supply for R/G/B output Power supply for R/G/B output Open emitter input

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) COINCIDENCE Pin No. Name Description Peripheral circuit of pin DC voltage B IN KILLER FILTER CONTRAST

31 FAST BLK 0V

7.5V to 0.5V 70k 100 V Sync detection pin Sync Hi Async Lo 50k

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) ID Filter Pin No. Name Description Peripheral circuit of pin DC voltage 3.58MHz X-tal CHROMA APC FILTER AUDIO BYPASS

36 TV IN

(Y IN) 2.5V 2.3V 3.3V 2.3V Pin used to connect an oscillator (3.58MHz) V 15.2k 20k 135 200 1.3k 40p 100 200 50k

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) X-TAL 4.43MHz Pin No. Name Description Peripheral circuit of pin DC voltage VCD GND SYNC SEP IN V(Y) SW OUT Emitter input -(R-Y) OUT 1.75V 3.2V 5.7V 2.3V -(B-Y) OUT Pin used to connect an oscillator (4.43MHz) Pin to output 6dB amplifier 57k 21k 41k 1.3k 100 135

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) AUDIO OUT Pin No. Name Description Peripheral circuit of pin DC voltage SECAM REF AUDIO VCC -(B-Y) IN 3.0V 3.2V 8.0V 3.0V 45 -(R-Y) IN FM DIRECT OUT 4.4V to 1.3V 20k 4.5k 4.5k 100 10k 6.9k 35.7k 45.4k

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) DESCRIPTION OF PIN (cont.) VIDEO OUT Pin No. Name Description Peripheral circuit of pin DC voltage VCO VIDEO APC FILTER 2.9V 2.2V or 5.7V 4.0V 14k 200

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) [DATA list] C 300001100 1 2 C 400011000 2 4 C 500110000 4 8 C 601100000 9 6 C 700001110 1 4 C 800011100 2 8 C 900111000 5 6 D 001110000 1 1 2 D 100011110 3 0 D 200111100 6 0 D 301111000 1 2 0 D 400001010 1 0 D 500010100 2 0 D 600101000 4 0 D 701010000 8 0 D 800010010 1 8 D 900100100 3 6 E 000100110 3 8 E 100100010 3 4 E 200100011 3 5 E 301000110 6 9 E 400110011 5 1 E 500110010 5 0 E 601000100 6 8 E 900100111 3 9 A 000000000 0 A 100000001 1 A 200000010 2 A 300000100 4 A 400001000 8 A 500010000 1 6 A 600100010 3 2 A 701000001 6 4 A 810000000 1 2 8 A 900000011 3 B 000000101 5 B 100001001 9 B 200010001 1 7 B 300100001 3 3 B 401000001 6 5 B 510000001 1 2 9 B 600000111 7 B 700001111 1 5 B 800011111 3 1 B 900111111 6 3 C 001111111 1 2 7 C 111111111 2 5 5 C 200000110 6 E 700110110 5 4 E 800100101 3 7 Data No. Dat a No. Data Data D7 D6 D5 D4 D3 D2 D1 D0 Decimal D7 D6 D5 D4 D3 D2 D1 D0 Decimal

PAL/NTSC SYSTEM SHINGLE-CHIP COLOR TV SIGNAL PROCESSOR M52340SP MITSUBISHI ICs (TV) INITIAL CONDITION No function D7 D6 D5 D4 D3 D2 D1 D0 DATA POS/NEG DELAY ADJ 00H 0 0 1 0 0 0 0 0 A6 A MUTE VCO ADJ 01H 0 0 1 0 0 0 0 0 A6 TRAP DBF DFA 4.5/6.0 02H 0 0 0 0 0 0 0 0 A0 AUDIO ATT 03H 0 1 0 0 0 0 0 0 A7 DEFEAT SHARPNESS 04H 0 0 1 0 0 0 0 0 A6 CONTRAST 05H 0 0 1 0 0 0 0 0 A6 AUTO TV/EXT DL TIME 06H 0 0 0 0 0 1 1 0 C2 TINT 07H 0 1 0 0 0 0 0 0 A7 COLOR 08H 0 0 1 0 0 0 0 0 A6 HPHASE 3.58 NTSC SECAM 09H 0 1 0 0 0 0 0 0 A7 BRIGHT 0AH 0 0 1 0 0 0 0 0 A6 DRIVE R 0BH 0 0 1 0 0 0 0 0 A6 DRIVE B 0CH 0 0 1 0 0 0 0 0 A6 CUT OFF R 0DH 1 0 0 0 0 0 0 0 A8 CUT OFF G 0EH 1 0 0 0 0 0 0 0 A8 CUT OFF B 0FH 1 0 0 0 0 0 0 0 A8 F TRAP 1 0 H 00 000 00 0 A 0 AFCG HST SERSW 1 3 H 00 000000 A 0 MUTE