M2MNV-11-R2/Q

M2MNV MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 1/6 http://www.m-system.co.jp/ Super-mini Signal Conditioners Mini-M Series ANALOG SWITCHING MODULE Functions & Features

• Switches between two analog signal channels
• Switches/Distributes one voltage signal to two channels Typical Applications
• Switching 1 – 5V DC signal: no contact failure that happens when using mechanical contacts for this purpose
• Switching low-speed pulse signals Model 29.5 (1.16) (2.99) mm (inch) 124 (4.88) MODEL: M2MNV-[1][2]-[3][4]

ORDERING INFORMATION

• Code number: M2MNV-[1][2]-[3][4] Specify a code from below for each of [1] through [4]. (e.g. M2MNV-11-M2/CE/Q)
• Specify the specification for option code /Q (e.g. /C01/S01) Note: Must be used with its socket. NOT installable to a multi-unit installation base. (e.g. model: M2BS-16) [1] SWITCHING CONTROL 1: Interlocking switching control (single-pole contact) 2: Independent switching control (double-pole contact) [2] INPUT 1: Current signal (no receiving resistor) 2: Current signal (receiving resistor 50 Ω) 3: Voltage signal [3] POWER INPUT AC Power M: 85 – 264 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) (Select ‘/N’ for ‘Standards & Approvals’ code.) M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) R2: 11 – 27 V DC (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) (Select ‘/N’ for ‘Standards & Approvals’ code.) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) [4] OPTIONS (multiple selections) Standards & Approvals (must be specified) /N: Without CE /CE: CE marking Other Options blank: none /Q: Option other than the above (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating TERMINAL SCREW MATERIAL /S01: Stainless steel GENERAL SPECIFICATIONS Construction: Plug-in Connection: M3 screw terminals (torque 0.8 N·m) Screw terminal: Chromated steel (standard) or stainless steel Housing material: Flame-resistant resin (black) Switching: Photo MOSFET relay Isolation: Signal channel to switching command contact to power Power indicator LED: Green light turns on when the power is supplied. Status indicator LED 1: Green light turns on when the signal channel 1 (A1-B1) is alive. Status indicator LED 2: Green light turns on when the signal channel 2 (A2-B1) is alive. INPUT & OUTPUT ■ Signal Channels Max. operational voltage range: ±50 V DC (min. span 10 mV) Max. operational current range: ±50 mA DC (min. span 1 mA) Max. operational frequency range: 100 Hz Receiving resistor: 50 Ω incorporated (input code 2)

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 2/6 http://www.m-system.co.jp/ ON resistance: ≤ 50 Ω per wire (ON resistance of photo MOSFET relay) ■ Output Current signal input (no receiving resistor): Equal to the input signal Current signal input (receiving resistor 50 Ω): Voltage signal equal to [Current × 50 Ω] Voltage signal input: Equal to the input signal ■ Switching Command: Relay or open collector Contact detecting: 5 V DC / 1 mA Detecting levels: ≤ 1 kΩ at ON / ≥ 10 kΩ at OFF INSTALLATION Power Consumption

• AC: Approx. 3 VA at 100 V Approx. 4 VA at 200 V Approx. 5 VA at 264 V
• DC: Approx. 2 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 150 g (0.33 lb) PERFORMANCE in percentage of span Accuracy: ±0.1 % (input code 2) Temp. coefficient: ±0.010 %/°C (±0.006 %/°F) (input code Switching response time: ≤ 5 msec. Leakage current at open circuit: ≤ 1 μA Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength:

2000 V AC @1 minute

(switching command contact to power to ground) (signal channel to power to ground)

1500 V AC @1 minute

(signal channel to switching command contact) STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 Low Voltage Directive EN 61010-1 Installation Category II Pollution Degree 2 Signal channel or switching command contact to power: Reinforced insulation (300 V) Signal channel to switching command contact: Basic insulation (300 V) RoHS Directive EN 50581

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 3/6 http://www.m-system.co.jp/ EXTERNAL VIEW

• Channel 2 Status LED 2
• Channel 1 Status LED 1 Power LED EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm 8 7 10 11 123 22 (.87) 6 (.24) 59 (2.32) 11–M3 SCREW 72 (2.83) 29.5 (1.16) 2–4.2x5 (.17x.20) MTG HOLE 6 (.24) deep
• When mounting, no extra space is needed between units. 21.5 (.85) 70.5 (2.78) 84 (3.31)10 (.39) DIN RAIL 35mm wide [4 (.16)] 114 (4.49) 4 (.16)

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 4/6 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Base Socket SWITCHING COMMAND SW1 50 Ω *1 50 Ω *1 ■ INTERLOCKING SWITCHING CONTROL (single-pole contact) Base Socket SWITCHING COMMAND SW1 SW2 *1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω). *2. Provided only with the input code 1: Current signal (no receiving resistor). *1/ *2 Not provided with the input code 3. A1-B1 channel is connected when the SW1 is turned on (closed). A2-B1 channel is connected when the SW2 is turned on (closed). *1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω). *2. Provided only with the input code 1: Current signal (no receiving resistor). *1/ *2 Not provided with the input code 3. A1-B1 channel is connected when the SW1 is turned on (closed). A2-B1 channel is connected when the SW1 is turned off (open). 50 Ω *1 50 Ω *1 ■ INDEPENDENT SWITCHING CONTROL (double-pole contact) Photo MOSFET Relay Driver 5kΩ 5kΩ B1-1 B1-2 A1-1 A1-2 A2-1 A2-2 B1-1 B1-2 A1-1 A1-2 A2-1 A2-2 5kΩ STATUS LED 1 POWER LED STATUS LED 2 STATUS LED 1 POWER LED STATUS LED 2 U(+) V(–) POWER U(+) V(–) POWER Photo MOSFET Relay Driver

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 5/6 http://www.m-system.co.jp/ SWITCHING OPERATIONS Current Signal (no receiving resistor) Power : OFF Switching command : OFF (open) 8Power : ON Switching command : OFF (open) 8Power : ON Switching command : ON (short) Current Signal (receiving resistor 50 Ω) Voltage Signal Current Signal (no receiving resistor) Transition (ON to OFF, OFF to ON) Status Power : ON Switching command : OFF to ON or Power : ON Switching command : ON to OFF Current Signal (receiving resistor 50 Ω) Voltage Signal *1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω). *1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω).

• Switching Status When the switching command contact is switched from OFF to ON or from ON to OFF, the signal channel is switched only after all photo MOSFET relays turn on (closed). When the switching command contact is switched from OFF to ON or from ON to OFF, the signal channel is switched only after all photo MOSFET relays turn off (open). ■ INTERLOCKING SWITCHING CONTROL (single-pole contact) Single contact is used to switch from Signal Channel 1 (A1 – B1) to Signal Channel 2 (A2 – B1) and vice versa. CHANNEL 1 (A1) CHANNEL 2 (A2) Terminal 3 – 9 OFF (open) OFF ON Terminal 3 – 9 ON (closed) ON OFF Status LED turn on when the respective channels are alive. ■ INDEPENDENT SWITCHING CONTROL (double-pole contact) Double contacts are used to independently switch Signal Channel 1 (A1 – B1) and Signal Channel 2 (A2 – B1). CHANNEL 1 (A1) CHANNEL 2 (A2) Terminal 3 – 9 OFF (open) OFF ---- Terminal 3 – 9 ON (closed) ON ---- Terminal 6 – 9 OFF (open) ---- OFF Terminal 6 – 9 ON (closed) ---- ON Status LED turn on when the respective channels are alive.

MODEL: M2MNV M2MNV SPECIFICATIONS ES-5095 Rev.9 Page 6/6 http://www.m-system.co.jp/ Specifications are subject to change without notice.