LTS-2807CKD-P LITEON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LED Display Product Data Sheet LTS-2807CKD-P Spec No.: DS30-2013-0118 Effective Date: 07/02/2014 Revision: A BNS-OD-FC001/A4 BNS-OD-FC001/A4 BNS-OD-FC001/A4 BNS-OD-FC001/A4

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P LED DISPLAY LTS-2807CKD-P Rev Description By Date 01 Preliminary Spec. Reo Lin 02/08/2013 02 Revised error for packing spec. in page 9 Reo Lin 10/21/2013 Above data for PD and Customer tracking only - NPPR Received and Upload on System Reo Lin 10/21/2013 A Modify symbol location in page 3 Reo Lin 06/26/2014

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 1. Description The LTS-2807CKD-P is a 0.2 inch (5.08mm) digit height single digit SMD display. This device uses AS-AlInGap hyper red chips(AlInGap epi on GaAs substrate). The display has gray face and white segments.

1.1 Features

 0.2 inch (5.08 mm) DIGIT HEIGHT  CONTINUOUS UNIFORM SEGMENTS  LOW POWER REQUIREMENT  EXCELLENT CHARACTERS APPEARANCE  HIGH BRIGHTNESS & HIGH CONTRAST  WIDE VIEWING ANGLE  SOLID STATE RELIABILITY  CATEGORIZED FOR LUMINOUS INTENSITY.  LEAD-FREE PACKAGE(ACCORDING TO ROHS)

1.2 Device

AlInGap Hyper Red Common Anode Rt. Hand Decimal LTS-2807CKD-P

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 2. Package Dimensions 1 5 610 5 1 6 10 Notes : 1. All dimensions are in millimeters. Tolerances are 0.25 mm (0.01“) unless otherwise noted 2. Foreign material on segment ≦10mil 3. Ink contamination (surface) ≦20mils 4. Bubble in segment ≦10mil 5. Bending ≦ 1% of reflector length 6. Plastic pin’s burr max is 0.05 mm

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 3. Internal Circuit Diagram

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 4. Pin Connection No Connection

1 CATHODE E

2 CATHODE D

3 COMMON ANDOE

4 CATHODE C

5 CATHODE DP

6 CATHODE B

7 CATHODE A

8 COMMON ANODE

9 CATHODE F

10 CATHODE G

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 5. Rating and Characteristics 5.1. Absolute Maximum Rating at Ta=25° C Parameter Maximum Rating Unit Power Dissipation Per Segment 70 mW Peak Forward Current Per Segment ( 1/10 Duty Cycle, 0.1ms Pulse Width ) 60 mA Continuous Forward Current Per Segment Derating Linear From 25° C Per Segment 0.28 mA mA/° C Operating Temperature Range -35° C to +105° C Storage Temperature Range -35° C to +105° C Iron Soldering Conditions: 1/16 inch Below Seating Plane for 3 Seconds at 260°C 5.2.Electrical / Optical Characteristics at Ta=25° C Parameter Symbol MIN. TYP . MAX. Unit Test Condition Average Luminous Intensity Per Segment IV 201 650 cd IF=1mA

8250 IF=10mA

Peak Emission Wavelength p 650 nm IF=20mA Spectral Line Half-Width  20 nm IF=20mA Dominant Wavelength d 639 nm IF=20mA Forward Voltage Per Chip VF 2.05 2.6 V IF=20mA Reverse Current Per Segment(2) IR 100 A VR=5V Luminous Intensity Matching Ratio (Similar Light Area) IV-m 2:1 IF=1mA Notes : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (Commission International De L’Eclariage) eye-response curve 2. Reverse voltage is only for IR test. It cannot continue to operate at this situation 3. Cross talk specification ≦ 2.5%

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 5.3. Typical Electrical / Optical Characteristics Curves (25°C Ambient Temperature Unless Otherwise Noted)

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 6. SMT SOLDERING INSTRUCTION (Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the first and the second soldering process) Notes : 1. Recommended soldering condition Reflow Soldering (Two times only) Soldering Iron (One time only) Pre-heat: Pre-heat time: Peak temperature: Soldering time: 120~150°C. 120sec. Max. 260°C Max. 5sec. Max. Temperature Soldering time 300°C Max. 3sec. Max. 2. Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the first and the second soldering process.

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 7. Recommended Soldering Pattern

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 8. Packing Specification 8.1. Packing Reel Dimensions PS 05 0304 0100 02 92 1112 101 7843 330.0±2.0 100.0±0.5 29.4 -0.5 24.4 13.0 +0.5 -0.2 2.0 +0.5 120° 21.0±0.5

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 8.2. Packing Carrier Dimensions 1. 10 sprocket hole pitch cumulative tolerance ± 0.20. 3. Material : Black Conductive Polystyrene Alloy. 2. Carrier camber is within 1 mm in 250 mm. 4. All dimensions meet EIA-481-D requirements. 6. Packing length per 22" reel : 56.5 Meters.(1:3) 7. Component load per 13" reel : 1000 pcs. 5. Thickness : 0.30± 0.05mm. 8.3.Trailer part / Leader part (40mm MIN.) (400mm MIN.) (40mm MIN.) DIRECTION OF PULLING OUT

Part No. : LTS-2807CKD-P BNS-OD-FC002 /A4 LED DISPLAY LTS-2807CKD-P 9. Moisture Proof Packing All N/D SMD displays are shipped in moisture proof package. The displays should be stored at 30° C or less and60% RH or less. Once the package opened, moisture absorption begins. If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. Baking should only be done once Package Temperature Time In Reel 60°C ≧48hours In Bulk 100°C ≧4hours 125°C ≧2hours