LTS-2806SKG-P LITEON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LED Display Product Data Sheet LTS-2806SKG-P Spec No. :DS30-2010-0095 Effective Date: 01/15/2020 Revision: A
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P LED DISPLAY LTS-2806SKG-P Rev Description By Date 01 Preliminary Spec. Eason Lin 02/09/2010
02 Correction Pin out Eason Lin 03/24/2010
03 Correction Pin 1 Position and Pin out Definition Eason Lin 09/15/2010
04 Change Reel Drawing Eason Lin 11/10/2010
Above data for PD and Customer tracking only - NPPR Received and Upload on System Eason Lin 11/1 0/2010 A Update Packing spec. in page 9 Reo Lin 01/10/2020
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 1. Description The LTS-2806SKG-P is a 0.28 inch (7.0 mm) digit height single digit SMD display. This device utilizes AlInGaP green LED chips which are made from AlInGaP on a non -transparent GaAs. The display has gray face and white segments.
1.1 Features
0.28 inch (7.0 mm) DIGIT HEIGHT CONTINUOUS UNIFORM SEGMENTS LOW POWER REQUIREMENT EXCELLENT CHARACTERS APPEARANCE HIGH BRIGHTNESS & HIGH CONTRAST WIDE VIEWING ANGLE SOLID STATE RELIABILITY CATEGORIZED FOR LUMINOUS INTENSITY. LEAD-FREE PACKAGE(ACCORDING TO ROHS)
1.2 Device
AlInGaP Green Common Anode LTS-2806SKG-P
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 2. Package Dimensions Notes : 1. All dimensions are in millimeters. Tolerances are ±0.25 mm (0.01“) unless otherwise noted 2. Foreign material on segment ≦10mil 3. Ink contamination (surface) 20mils≦ 4. Bubble in segment ≦10mil 5. Bending ≦ 1% of reflector length 6. Plastic pin’s burr max is 0.1 mm
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 3. Internal Circuit Diagram 4. Pin Connection No Connection
1 NO CONNECTION
2 CATHODE D
3 CATHODE E
4 COMMON ANODE
5 CATHODE C
6 CATHODE DP
7 CATHODE B
8 CATHODE A
9 COMMON ANODE
10 CATHODE F
11 NO CONNECTION
12 CATHODE G
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 5. Rating and Characteristics 5.1. Absolute Maximum Rating at Ta=25° C Parameter Maximum Rating Unit Power Dissipation Per Segment 70 mW Peak Forward Current Per Segment ( 1/10 Duty Cycle, 0.1ms Pulse Width ) 60 mA Continuous Forward Current Per Segment Derating Linear From 25° C Per Segment 0.28 mA mA/° C Operating Temperature Range -35° C to +105° C Storage Temperature Range -35° C to +105° C Iron Soldering Conditions: 1/16 inch Below Seating Plane for 3 Seconds at 260 °C 5.2.Electrical / Optical Characteristics at Ta=25° C Parameter Symbol MIN. TYP . MAX. Unit Test Condition Average Luminous Intensity Per Segment IV 201 501 µcd IF=2mA 5210 µcd IF=20mA Peak Emission Wavelength λp 574 nm IF=20mA Spectral Line Half-Width Δλ 15 nm IF=20mA Dominant Wavelength λd 571 nm IF=20mA Forward Voltage Per Chip VF 2.05 2.6 V IF=20mA Reverse Current Per Segment (2) IR 100 µA VR=5V Luminous Intensity Matching Ratio (Similar Light Area) IV-m 2:1 IF=2mA Notes : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (Commission International De L’Eclariage) eye-response curve 2. Reverse voltage is only for IR test. It cannot continue to operate at this situation 3. Cross talk specification ≦ 2.5%
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 5.3. Typical Electrical / Optical Characteristics Curves
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 6. SMT SOLDERING INSTRUCTION (Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the f irst and the second soldering process) Notes : 1. Recommended soldering condition Reflow Soldering (Two times only) Soldering Iron (One time only) Pre -heat: Pre-heat time: Peak temperature: Soldering time: 120~150 °C. 120sec. Max. 260° C Max. 5sec. Max. Te mperature Soldering time 300 °C Max. 3sec. Max. Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the first and the second soldering process.
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 7. Recommended Soldering Pattern 8. Packing Specification 8.1. Packing Reel Dimensions PS 6 05 03 00 02 92 11 12 10 1 7843 330.0±2.0 100.0±0.5 29.4 -0.5 24.4 13.0 +0.5 -0.2 2.0 +0.5 120° 21.0±0.5
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 8.2. Packing Carrier Dimensions 1. 10 sprocket hole pitch cumulative tolerance ±0.20. 3. Material : Black Conductive Polystyrene Alloy. 2. Carrier camber is within 1 mm in 250 mm. 4. All dimensions meet EIA-481 requirements. 6. Packing length per 22" reel : 38.5 Meters. 7. Component load per 13" reel : 1000 pcs. 5. Thickness : 0.40±0.05mm. DIRECTION OF PULLING OUT 8. Minimum packing quantity is 250 pcs for remainders 1 1 1 8.3.Trailer part / Leader part (40mm MIN.) (400mm MIN.) (40mm MIN.) DIRECTION OF PULLING OUT
Part No. : L TS-2806 SKG -P BNS-OD-FC002 /A4 LED DISPLAY LTS-2806SKG-P 9. Moisture Proof Packing All N/D SMD displays are shipped in moisture proof package. The displays should be stored at 30° C or less and 60% RH or less. Once the package opened, moisture absorption begins. If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. Baking should only be done once Package Temperature Time In Reel 60 °C ≧48hours In Bulk 100 °C ≧4hours 125 °C ≧2hours