LD7523 LEADTREND | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 18

Technical content

Features

z High-Voltage CMOS Process with Excellent ESD protection z Very Low Startup Current (< 35μA) z Current Mode Control z Non-audible-noise Green Mode Control z UVLO (Under Voltage Lockout) z LEB (Leading-Edge Blanking) on CS Pin z Internal Slope Compensation z Programmable Line Compensation z OVP (Over Voltage Protection) z OLP (Over Load Protection) z Brownout Protection z Built in OLP De-Latch Timer z 500mA Driving Capability

Applications

z Switching AC/DC Adaptor and Battery Charger z Open Frame Switching Power Supply z LCD Monitor/TV Power Typical Application EMI Filter BNO OUT CS VCC GND COMP LD7523 photocoupler AC input TL431 OVP

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Pin Configuration SOP-8 & DIP-8(TOP VIEW) 2 3 4 7 6 5 TOP MARK YYWWPP BNO COMP NC CS OVP VCC OUT GN D YY : Year code (D: 2004, E: 2005…..) WW : Week code ## : Production code

Ordering Information

Part number Package TOP MARK Shipping LD7523 GS SOP-8 Green Package LD7523GS 2500 /tape & reel LD7523 GN DIP-8 Green Package LD7523GN 3600/tube /carton The LD7523 is ROHS Complaint/ Green Package. Pin Descriptions PIN NAME FUNCTION

1 BNO

Brownout Protection Pin. Connect a resistor divider between this pin and bulk capacitor voltage to set the brownout level and line compensation. When the voltage of this pin fall below threshold voltage, the PWM output will be shut off.

2 COMP

Voltage feedback pin (same as the COMP pin in UC384X). Connect it with a photo-coupler to close the control loop and achieve the regulation.

3 NC NC

4 CS Current sense pin, connec t to sense the MOSFET current

5 GND Ground

6 OUT Gate drive output to drive the external MOSFET

7 VCC Supply voltage pin

8 OVP

This pin is active-high to provide the OVP function. Connecting a zener or a resistor voltage divider to Vcc will set the OVP level. Once the voltage rise above 2.5V, the OVP will be tripped and the gate drive off. Short this pin to ground to disable the OVP function.

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Block Diagram Green - Mode Control COMP CS OUT internal bias & Vref GND PWM Comparator R R SQ + Slope Compensation 2.5V 0.85V OLP Delay5.0V OCP Comparator OLP Comparator Driver Stage OVP Comparator VCC OK Line Compensation 12.75V /9.75V UVLO Comparator Vref OK VCC OVP BNO Gain = 0.04 Line Compensation R SQ PG =OLP =OVP Vbias PG 65KHz OSC PG PG 1.25V /1.10V Brownout Comparator = ACUV De-Latch Counter Leading Edge Blanking Auto Recoverable Protections

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Absolute Maximum Ratings Supply Voltage VCC -0.3V~30V COMP, BNO, CS -0.3V ~7V OUT -0.3V ~Vcc+0.3V Maximum Junction Temperature 150° C Operating Ambient Temperature Range -40 °C to 85°C Operating Junction Temperature Range -40 °C to 125°C Storage Temperature Range -65 °C to 150°C Package Thermal Resistance (SOP-8) 160° C/W Package Thermal Resistance (DIP-8) 100° C/W Power Dissipation (SOP-8, at Ambient Temperature = 85°C) 400mW Power Dissipation (DIP-8, at Ambient Temperature = 85°C) 650mW Lead temperature (Soldering, 10sec) 260° C ESD Voltage Protection, Human Body Model 2.5KV ESD Voltage Protection, Machine Model 250V Gate Output Current 500mA Caution: Stresses beyond the ratings specified in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above t hose indicated in the operational sections of this s pecification is not implied.

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009

Electrical Characteristics

(TA = +25oC unless otherwise stated, VCC=12.0V) PARAMETER CONDITIONS MIN TYP MAX UNITS Supply Voltage (VCC Pin) Startup Current 20 35 μA VCOMP=0V 3.5 mA VCOMP=3V 2.7 mA Operating Current (with 1nF load on OUT pin) Protection Mode (note 1) 0.70 mA UVLO (off) 9.0 9.75 10.7 V UVLO (on) 12.0 12.75 13.5 V Voltage Feedback (Comp Pin) Short Circuit Current VCOMP=0V 2.5 4.0 mA Green Mode Threshold VCOMP 2.35 V Current Sensing (CS Pin) VBNO=0V (note 2) 0.80 0.85 0.90 V VBNO=1.30V 0.748 0.798 0.848 V Maximum Input Voltage, VCS(OFF) VBNO=3.75V 0.650 0.700 0.750 V Leading Edge Blanking Time 350 nS Input impedance 1 NA M Ω Delay to Output 200 nS Gate Drive Output (OUT Pin) Output Low Level VCC=15V, Io=20mA 1.0 V Output High Level VCC=15V, Io=20mA 9.0 V Rising Time VCC=15V,Load Cap.=1000pF 50 160 nS Falling Time VCC=15V ,Load Cap.=1000pF 30 60 nS Oscillator Frequency 60 65 70 KHz Green Mode Frequency 20 KHz Frequency Temp. Stability (-40°C –85°C) 3 % Frequency Voltage Stability (VCC=12V-30V) 1 %

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Electrical Characteristics (Continued) (TA = +25oC unless otherwise stated, VCC=12.0V) PARAMETER CONDITIONS MIN TYP MAX UNITS Brownout Protection & Line Compensation (BNO Pin) Brownout Turn-On Trip Level 1.20 1.25 1.30 V Brownout Turn-Off Trip Level 1.05 1.10 1.15 V Saturation Voltage on LINE Pin I BNO<1.5uA 5.0 V Line Compensation Ratio 0.04 V/V Over Voltage Protection (OVP Pin) OVP Trip Level 2.35 2.50 2.65 V OVP de-bounce time 200 μS Saturation Voltage on OVP Pin I OVP<1.5uA 5.0 V OLP (Over Load Protection) OLP Trip Level VCOMP(OLP) 4.5 5.0 5.5 V OLP Delay Time VCOMP>5.0V 60 mS OLP De-Latch Counter 500 mS Soft Start Soft Start Duration 5 7.5 10 mS Note 1: When OVP, OLP Protection is tripped. Note 2: Guaranteed by design because Vcs(off) can’t be measured when VBNO=0V.

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Typical Performance Characteristics UVLO (on) (V) Fig. 1 UVLO (on) vs. Temperature 10.0 -40 0 40 80 120 Temperature (°C) 11.0 12.0 13.0 15.0 14.0 UVLO (off) (V) Fig. 2 UVLO (off) vs. Temperature -40 04 0 80 120 Temperature (°C) 8.0 8.8 9.6 10.4 11.2 12.0 Frequency (KHz) Temperature (°C) Fig. 3 Frequency vs. Temperature -40 0 40 80 120 Green Mode Frequency (KHz) Temperature (°C) Fig. 4 Green Mode Frequency vs. Temperature -40 0 40 80 120 Frequency (KHz) VCC (V) Fig. 5 Frequenc y vs. VCC 12 14 16 18 20 22 2460 Green Mode Frequency (KHz) VCC (V) Fig. 6 Green Mode Frequency vs. V CC 12 14 16 18 20 22 24

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Max Duty Cycle (%) Fig. 7 Max Duty Cycle vs. Temperature -40 0 40 80 120 Temperature (°C) VCS (off) (V) Fig. 8 Vcs (off) vs. Temperature -40 0 40 80 120 Temperature (°C) 0.65 0.70 0.75 0.80 0.85 0.90 0.60 VLINE= 0V VLINE=1.25V VLINE=3.75V Startup Current (μA) Fig. 9 Startup Current vs. Temperature -40 0 40 80 120 Temperature (°C) OVP (V) Temperature (°C) Fig. 10 OVP-Trip Level vs. Temperature -40 0 40 80 120 2.45 2.50 2.55 2.60 2.40 VCOMP (V) Fig. 11 V COMP open-loop voltage vs. Temperature Temperature (°C) -40 0 40 80 120 5.0 5.2 5.4 5.6 5.8 6.0 OLP (V) Fig. 12 OLP-Trip Level vs. Temperature Temperature (°C) -40 0 40 80 120 4.5 4.7 4.9 5.1 5.3 5.5

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 ILINE (μA) VLINE Fig. 13 V LINE vs. ILINE 0 1 2 3 4 5 125°C 25°C -40°C IOVP (μA) VOVP Fig. 14 V OVP vs. IOVP 0 1 2 3 4 5 125°C 25°C -40°C BNO Pin On (V) Temperature (°C) Fig. 15 BNO Pin On Level vs. Temperature -4 0 0 40 80 120 1.23 1.24 1.25 1.26 1.27 BNO Pin Off (V) Temperature (°C) Fig. 16 BNO Pin Off Level vs. Temperature -40 0 40 80 120 1.050 1.075 1.100 1.125 1.150

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009

Application Information

As long as the green power requirement becomes a trend and the power saving is getting more and more important for the switching power supplies and switching adapters, traditional PWM controllers are not able to support such new requirements. Furthermore, the cost and size limitation forces the PWM c ontrollers to powerfully integrate more functions fo r reducing the external part counts. The LD7523 is tar geted on such applications and provides an easy and cost effective solution; its detailed features are described as below. Under Voltage Lockout (UVLO) An UVLO comparator is implemented in it to detect the voltage on the VCC pin, for assuring the supply voltage high enough to turn on the LD7523 PWM controller and to drive the power MOSFET. As shown in Fig. 19, a hysteresis is built in to pr event the shutdown due to the voltage dip during startup. The turn-on and turn-off threshold levels are set at 12.75V and 9.75V, respectively. Vcc UVLO(on) UVLO(off) t t I(Vcc) startup current (~uA) operating current (~ mA) Fig. 19 Startup Current and Startup Circuit The typical startup circuit for the LD7523 is shown in Fig. 20. During the startup transient, the Vcc is lower than UVLO threshold and thus there is no gate pulse produced from the LD7523 to drive po wer MOSFET. Therefore, the current through R1 will provi de the startup current and to charge the capacitor C1. Once upon the Vcc voltage is high enough to turn on the LD7523 and further to deliver the gate drive signal, the supply current is provided from the auxiliary winding of t he transformer. Lower startup current requirement for the PWM controller will help to increase the maximum value on R1 and then reduce the power consumption on R1. By using CMOS process and the special circuit design, t he maximum startup current of LD7523 is only 35μA. If a higher resistance value of t he R1 is chosen, it usually takes more time to start up. To carefully select the value of R1 and C1 will optimize the power consumption and startup time. EMI Filter OUT CS VCC GND LD7523 AC input Cbulk D1 Fig. 20 Output Stage and Maximum Duty-Cycle An output stage of a CMOS buffer, with typical 500mA driving capability, is incorporated to drive a power

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 MOSFET directly. And the maximum duty-cycle of LD7523 is limited to 75% to avoid the transformer saturation. Oscillator and Switching Frequency The switching frequency of LD7523 is fixed as 65KHz internally to provide the optimized operations by considering the EMI performance, thermal treatment, component sizes and transformer design. Voltage Feedback Loop The voltage feedback signal is provided from the TL431 in the secondary side through the photo-coupler to the COMP pin of LD7523. The input stage of LD7523, like the UC384X, has 2 diodes voltage offset before feeding into the voltage divider with 1/3 ratio, that is, ) V 2 V (3 1)V FCOMPPWM (COMPARATOR −× =+ A pulling-high resistor is embedded internally to eliminate the requirement of another resistor in the external circuit. Dual-Oscillator Green-Mode Operation There are many different topologies implemented in different chips for the green-mode or power saving requirements, such as “burst-mode control”, “skipping-cycle mode”, “variable off-time control “…etc. The basic operation theory of all these approaches intends to reduce the switching cycles under light-load or no-load condition either by skipping some switching pulses or reduce the switching frequency. By using this dual-oscillator control, the green-mode frequency can be well controlled and further to avoid the generation of audible noise. Internal Slope Compensation A fundamental issue of current mode control is the stability problem when its duty-cycle is over 50%. To stabilize the control loop, slope compensation is required in the traditional UC384X design by injecting the ramp signal from the RT/CT pin through a coupling capacitor. In the LD7523, the internal slope compensation circuit has been internally implemented to simplify the external circuit design. Current Sensing, Leading-Edge Blanking The typical current mode PWM controller feedbacks both current signal and voltage signal to close the control loop and achieve regulation. The LD7523 detects the primary MOSFET current from the CS pin, which is not only for the peak current mode control but also for the pulse-by-pulse current limit. The maximum voltage threshold of the current sensing pin is set as 0.85V. Thus the MOSFET peak current can be calculated as: S ONCOMPENSATI_ LINE ) MAX ( PEAK R )V 85 . 0 ( I A 350nS leading-edge blanking (LEB) time is included in the input of CS pin to prevent the false-trigger from the current spike. However, th e total pulse width of the turn-on spike is decided by the output power, circuit design and PCB layout. It is strongly recommended to adopt a smaller R-C filter (as shown in figure 21) to avoid the CS pin being damaged by the negative turn-on spike. Fig. 21

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Brownout Protection & Line Compensation The LD7523 employs BNO pin to set the brownout protection point and the li ne voltage OVP point though BNO pin. The voltage across the BNO pin is proportional to the bulk capacitor voltage, referred as the line voltage. A brownout comparator is implemented to detect the abnormal line condition. As soon as the condition is detected, it will shut down the controller to prevent the damage. Figure 22 shows the operation. When V BNO falls below 1.25V, the gate output will be kept off even Vcc has already achieved UVLO( ON). It therefore makes Vcc hiccup between UVLO( ON) and UVLO( OFF). Unless the line voltage is large enough to pull VBNO larger than 1.25V, the gate output will not start switching even when the next UVLO(ON) is tripped. A hysteresis is implemented to prevent the false trigger during turn-on and turn-off. Meanwhile, LD7523 detects the voltage across BNO pin to feed the line compensation signal to the current sense circuit. Figure 23 shows the circuit. The OCP level of high-line and low-line can be set to a very close point. The voltage gain from the BNO voltage to line compensation is 0.04 (V/V). The relationship between BNO pin voltage and the line compensation is illustrated in figure 24. 1.25V t Vcc t OUT SwitchingNon-Switching t VBNO t Line Voltage 1.10V AC OK area UVLO(on) UVLO(off) Fig. 22 acV⋅2 Fig. 23

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Vpin1 Line Compensation 1.30V 52mV 160mV gain=0.04 150mV 3.75V Linear Region 4.0V Turn-Off Region Fig. 24 Over Load Protection (OLP) To protect the circuit from damage under over load condition or short condition, a smart OLP function is implemented in the LD7523. Figure 25 shows the waveforms of the OLP operation. In such cases, the feedback system will force the feedback voltage loop toward the saturation and pull the voltage of COMP pin (VCOMP) to high. Once the VCOMP trips the OLP threshold of 5.0V and stays for more than 60mS, the protection will be activated and then turns off the gate output to stop the switching of power circuit. The 60mS delay time is to prevent the false trigger from the power-on and turn-off transient. The Fig. 26 shows the other application example. The VCC of LD7523 will be supplied by an auxiliary source voltage (e.g. standby power) instead. Once the voltage of COMP pin trips the OLP threshold voltage (5.0V) and stays for more than 60mS, OUT pin will stop switching soon. The VCC voltage will not descend since VCC is supplied by an auxiliary voltage source. Otherwise, the internal OLP de-latch counter will active and count for a skipping duration (500mS). It is called as OLP SKIP DURATION. The OUT pin will stop switching until the OLP de-latch counter is reset and then resume to normal switching. By using such protection me chanism, the average input power can be reduced to minimum level to control the component temperature and stress within the safety operation area. VCC UVLO(on) UVLO(off) T T COMP Over Load T OUT OLP Delay Time Switching Switching Non-Switching OLP Delay Time Over Load Switching OLP Delatch by UVLO(off) Fig. 25

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 VCC UVLO(on) UVLO(off) T T COMP Over Load T OUT OLP Delay Time Switching Switching Non-Switching OLP skip duration OLP Delay Time OLP skip duration Over Load Switching OLP Delatch by Internal Counter Fig. 26 Over Voltage Protection (OVP) To prevent the component from damage due to fault condition, LD7523 is implemented with protection through the OVP pin. Figure 27 and figure 28 show 2 different configurations to program the OVP setting point --- zener detection and voltage divider. It provides zero bias current during normal operation so that it will not affect the startup timing, as figure 27. But the tolerance of OVP trip point will be larger due to the distribution of the breakdown voltage of zener diode. On the other hand, using the circuit of figure 28 will be beneficial from the minimum cost and higher OVP accuracy, but it requires larger value of R1 and R2 to avoid affecting on startup timing by the load effect. As shown in figure 29, if t he voltage on the OVP pin rise above threshold voltage of 2.5V, the output gate drive circuit will be shutdown simultaneous in order to stop switching the power MOSFET. But if the voltage on the OVP pin drops below 2.5V, it will automatically resume to the normal operation on the next UVLO(on) level. VCC GND LD7523 OVP Vz Vbulk-cap V(OVP)= Vz+2.5V Fig. 27 21 ( 5 . 2 ) (R RVOVPV + ⋅ = Fig. 28 VCC UVLO(on) UVLO(off) t OVP Tripped t OUT Switching SwitchingNon-Switching OVP Level Fig. 29

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Summary of Protections There are several ways to control the on/off of LD7523. The details are listed as the table below. Turn Off Operation COMP Comp Pin < 1.4V Cycle by Cycle Mode Non-latch OLP Comp Pin > 5.0V OVP OVP Pin > 2.5 V Hiccup Mode Non-latch Re-start after next UVLO(on) Brownout BNO Pin < 1.25V with Hysteresis Cycle by cycle mode Non-latch Table 1

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009

Package Information

Dimensions in Millimeters Dimensions in Inch Symbols MIN MAX MIN MAX A 4.801 5.004 0.189 0.197 B 3.810 3.988 0.150 0.157 C 1.346 1.753 0.053 0.069 D 0.330 0.508 0.013 0.020 F 1.194 1.346 0.047 0.053 H 0.178 0.229 0.007 0.009 I 0.102 0.254 0.004 0.010 J 5.791 6.198 0.228 0.244 M 0.406 1.270 0.016 0.050 θ 0° 8° 0° 8°

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009 Dimension in Millimeters Dimensions in Inches Symbol Min Max Min Max A 9.017 10.160 0.355 0.400 B 6.096 7.112 0.240 0.280 D 0.356 0.584 0.014 0.023 E 1.143 1.778 0.045 0.070 F 2.337 2.743 0.092 0.108 I 2.921 3.556 0.115 0.140 J 7.366 8.255 0.29 0.325 Important Notice Leadtrend Technology Corp. reserves the right to make changes or corrections to its products at any time without notice. Custom ers should verify the datasheets are current and complete before placing order.

Leadtrend Technology Corporation www.leadtrend.com.tw LD7523-DS-00 June 2009

Revision History

Rev. Date Change Notice 00 6/16/2009 Original Specification.