LC322271J SANYO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 29

Technical content

Features

  • 131072 words · 16 bits configuration.
  • Single 5 V ± 10% power supply.
  • All input and output (I/O) TTL compatible.
  • Supports fast page mode, read-modify-write and byte write.
  • Supports output buffer control using early write and Output Enable (OE) control.
  • 8 ms refresh using 512 refresh cycles.
  • Supports RAS-only refresh, CAS-before-RAS refresh and hidden refresh.
  • Follows the JEDEC 1 M DRAM (65536 words · 16 bits, 1CAS/2WE) standard.
  • RAS access time/column address time/CAS access time/cycle time/power dissipation
  • Package: SOJ 40-pin (400 mil) plastic package : LC322271J SOP 40-pin (450 mil) plastic package: LC322271M TSOP 44-pin (400 mil) plastic package : LC322271T Package Dimensions unit: mm 3200-SOJ40 Preliminary SANYO: SOJ40 [LC322271J] LC322271J, M, T-70/80 SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-0005 JAPAN

2 MEG (131072 words · 16 bits) DRAM

Fast Page Mode, Byte Write CMOS LSI Parameter LC322271J, M, T -70 -80 RAS access time 70 ns 80 ns Column address access time 35 ns 45 ns CAS access time 20 ns 30 ns Cycle time 130 ns 150 ns Power dissipation (max.) During operation 688 mW 633 mW During standby 5.5 mW (CMOS level)/11 mW (TTL level)

unit: mm 3195-SOP40 Pin Assignments No. 5085-2/29 LC322271J, M, T-70/80 SANYO: SOP40 [LC322271M] unit: mm 3207-TSOP44 SANYO: TSOP44 (TYPE II) [LC322271T]

Note: 1. Stresses greater than the above listed maximum values may result in damage to the device. No. 5085-3/29 LC322271J, M, T-70/80 Parameter Symbol Ratings Unit Note Maximum supply voltage VCC max –1.0 to +7.0 V 1 Input voltage VIN –1.0 to +7.0 V 1 Output voltage VOUT –1.0 to +7.0 V 1 Allowable power dissipationLC322271J, M Pd max 800 mW 1 LC322271T 700 Output short-circuit current IOUT 50 mA 1 Operating temperature range Topr 0 to +70 °C 1 Storage temperature range Tstg –55 to +150 °C 1

DC Recommended Operating Ranges at Ta = 0 to +70°C Note: 2. All voltages are referenced to VSS . *: –2.0 V when pulse width is less than 20 ns. Note: 3. All current values are measured at minimum cycle rate. Since current flows immoderately, if cycle time is longer than shown here, current value becomes smaller. 4. ICC1 and ICC4 are dependent on output loads. Maximum values for ICC1 and ICC4 represent values with output open. 5. Address change is less than or equal to one time during RAS = VIL. Concerning ICC4 , it is less than or equal to one time during 1 cycle (tPC ). No. 5085-4/29 LC322271J, M, T-70/80 Parameter Symbol min typ max Unit Note Power supply voltage VCC 4.5 5.0 5.5 V 2 Input high level voltage VIH 2.4 6.5 V 2 Input low level voltage VIL –1.0* +0.8 V 2(A0 to A7, A8R, RAS, CAS, UW, LW, OE) Input low level voltage (I/O1 to I/O16) VIL –0.5* +0.8 V 2 Parameter Symbol -70 -80 Unit Note min max min max Random read, write cycle time tRC 130 150 ns Read-write/read-modify-write cycle time tRWC 190 200 ns Fast page mode cycle time tPC 45 55 ns Fast page mode read-write/read-modify-write cycle timetPRWC 95 100 ns RAS access time tRAC 70 80 ns 9, 14, 15 CAS access time tCAC 20 30 ns 9, 14 Column address access time tAA 35 45 ns 9, 15 CAS precharge access time tCPA 40 50 ns 9 Output low-impedance time from CAS low tCLZ 0 0 ns 9 Output buffer turn-off delay time tOFF 0 20 0 20 ns 10 Rise, fall time tT 3 50 3 50 ns RAS precharge time tRP 50 60 ns RAS pulse width tRAS 70 10000 80 10000 ns RAS pulse width for fast page mode cycle only tRASP 70 100000 80 100000 ns Continued on next page. LC322271J, M, T Parameter Symbol Conditions -70 -80 Unit Note min max min max Operating current ICC1 RAS, CAS, address cycling: tRC = tRC min 125 115 mA 3, 4, 5(Average current during operation) Standby current ICC2 RAS = CAS = VIH 2 2 mA RAS-only refresh current ICC3 RAS cycling, CAS = VIH: tRC = tRC min 125 115 mA 3, 5 Fast page mode current ICC4 RAS = VIL, CAS, address cycling: tPC = tPC min 115 90 mA 3, 4, 5 Standby current ICC5 RAS = CAS = VCC – 0.2 V 1 1 mA CAS-before-RAS refresh current ICC6 RAS, CAS cycling: tRC = tRC min 125 115 mA 3 Input leakage current IIL 0 V ≤ VIN ≤ 6.5 V, pins other than test pin = 0 V–10 +10 –10 +10 µA Output leakage current IOL D OUT disable, 0 V ≤ VOUT ≤ 5.5 V –10 +10 –10 +10 µA Output high level voltage VOH IOUT = –2.5 mA 2.4 2.4 V Output low level voltage VOL IOUT = 2.1 mA 0.4 0.4 V

Continued from preceding page. No. 5085-5/29 LC322271J, M, T-70/80 -70 -80 Parameter Symbol min max min max Unit Note RAS hold time tRSH 20 30 ns CAS hold time tCSH 70 80 ns CAS pulse width tCAS 20 10000 30 10000 ns RAS to CAS delay time tRCD 25 50 25 50 ns 14 RAS to column address delay time tRAD 17 35 17 35 ns 15 CAS to RAS precharge time tCRP 10 10 ns CAS precharge time tCP 10 10 ns Row address setup time tASR 0 0 ns Row address hold time tRAH 12 12 ns Column address setup time tASC 0 0 ns Column address hold time tCAH 15 20 ns Column address hold time referenced to RAS tAR 50 60 ns Column address to RAS lead time tRAL 40 45 ns Read command setup time tRCS 0 0 ns Read command hold time referenced to CAS tRCH 0 0 ns 11 Read command hold time referenced to RAS tRRH 0 0 ns 11 Write command hold time tWCH 15 15 ns Write command hold time referenced to RAS tWCR 50 60 ns Write command pulse width tWP 15 15 ns Write command to RAS lead time tRWL 25 25 ns Write command to CAS lead time tCWL 20 20 ns Data input setup time tDS 0 0 ns 12 Data input hold time tDH 15 20 ns 12 Data input hold time referenced to RAS tDHR 50 60 ns Refresh time tREF 8 8 ms Write command setup time tWCS 0 0 ns 13 CAS to UW, LW delay time tCWD 50 50 ns 13 RAS to UW, LW delay time tRWD 100 100 ns 13 Column address to UW, LW delay time tAWD 65 65 ns 13 CAS precharge UW, LW delay time for fast page mode tCPWD 70 70 ns 13cycle only CAS setup time for CAS-before-RAS tCSR 10 10 ns CAS hold time for CAS-before-RAS tCHR 15 15 ns RAS precharge CAS active time tRPC 10 10 ns CAS precharge time for CAS-before-RAS counter test tCPT 40 40 ns RAS hold time referenced to OE tROH 15 15 ns OE access time tOEA 20 25 ns 9 OE delay time tOED 15 15 ns OE output buffer turn-off delay time tOEZ 0 0 15 ns 10 OE command hold time tOEH 20 20 ns Data input to CAS delay time tDZC 0 0 ns 16 Data input to OE delay time tDZO 0 0 ns 16 Masked write setup time tMCS 0 0 ns Masked write hold time referenced to RAS tMRH 0 0 ns Masked write hold time referenced to CAS tMCH 0 0 ns

Input/Output Capacitance at Ta = 25°C, f = 1 MHz, VCC = 5 V ± 10% Note: 6. An initial pause of 200 µs is required after power-up followed by eight RAS-only refresh cycles before proper device operation is achieved. In case of using refresh counter, a minimum of eight CAS-before-RAS refresh cycles instead of eight RAS-only refresh cycles are required. 7. Measured at tT = 5 ns. 8. When measuring input signal timing, VIH (min) and VIL(max) are used for reference points. In addition, rise and fall time are defined between VIH and VIL. 9. Measured using an equivalent of 50 pF and one standard TTL loads. 10. tOFF (max) and tOEZ (max) are defined as the time until output voltage can no longer be measured when output switches to a high impedance condition. 11. Operation is guaranteed if either tRRH or tRCH is satisfied. 12. These parameters are measured from the falling edge of CAS for an early-write cycle, and from the falling edge of UW and LW for a read- write/read-modify-write cycle. 13. tWCS , tCWD , tRWD , tAWD and tCPWD are not restrictive operating parameters for memory in that they specify the operating mode. If tWCS ‡ tWCS (min), the cycle switches to an early-write cycle and output pins switch to high impedance throughout the cycle. If tCWD ‡ tCWD (min), tRWD ‡ tRWD (min), tAWD ‡ tAWD (min) and tCPWD ‡ tCPWD (min) for fast page mode cycle only, the cycle switches to a read-write/read-modify-write cycle and data output equal information in the selected cells. If neither of the above timings are satisfied, output pins are in an undefined state. 14. tRCD (max) is not a restrictive operating parameter but instead represents the point at which the access time tRAC (max) is guaranteed. If tRCD ‡ tRCD (max), access time is determined according to tCAC . 15. tRAD (max) is not a restrictive operating parameter but instead represents the point at which the access time tRAC (max) is guaranteed. If tRAD ‡ tRAD (max), access time is determined according to tAA . 16. Operation is guaranteed if either tDZC or tDZO i s satisfied. No. 5085-6/29 LC322271J, M, T-70/80 Parameter Symbol min max Unit Note Input capacitance (A0 to A7, A8R, RAS, CAS, UW, LW, OE) C IN 7 pF Input/Output capacitance (I/O1 to I/O16) C I/O 7 pF

No. 5085-7/29 LC322271J, M, T-70/80

No. 5085-8/29 LC322271J, M, T-70/80

Upper Byte Early Write Cycle No. 5085-9/29 LC322271J, M, T-70/80

Lower Byte Early Write Cycle No. 5085-10/29 LC322271J, M, T-70/80

Write Cycle (OE Control) No. 5085-11/29 LC322271J, M, T-70/80

Upper Byte Write Cycle (OE Control) No. 5085-12/29 LC322271J, M, T-70/80

Lower Byte Write Cycle (OE Control) No. 5085-13/29 LC322271J, M, T-70/80

No. 5085-14/29 LC322271J, M, T-70/80

Read-Modify Upper Byte Write Cycle No. 5085-15/29 LC322271J, M, T-70/80

Read-Modify Lower Byte Write Cycle No. 5085-16/29 LC322271J, M, T-70/80

No. 5085-17/29 LC322271J, M, T-70/80

Fast Page Mode Early Write Cycle No. 5085-18/29 LC322271J, M, T-70/80

Fast Page Mode Upper Byte Early Write Cycle No. 5085-19/29 LC322271J, M, T-70/80

Fast Page Mode Lower Byte Early Write Cycle No. 5085-20/29 LC322271J, M, T-70/80

Fast Page Mode Read-Modify-Write Cycle No. 5085-21/29 LC322271J, M, T-70/80

Fast Page Mode Read-Modify Upper Byte Write Cycle No. 5085-22/29 LC322271J, M, T-70/80

Fast Page Mode Read-Modify Lower Byte Write Cycle No. 5085-23/29 LC322271J, M, T-70/80

No. 5085-24/29 LC322271J, M, T-70/80

CAS-Before-RAS Refresh Cycle No. 5085-25/29 LC322271J, M, T-70/80

CAS-Before-RAS Refresh Counter Test Cycle (Read) No. 5085-26/29 LC322271J, M, T-70/80

CAS-Before-RAS Refresh Counter Test Cycle (Write) No. 5085-27/29 LC322271J, M, T-70/80

CAS-Before-RAS Refresh Counter Test Cycle (Read-Modify-Write) No. 5085-28/29 LC322271J, M, T-70/80

PS No. 5085-29/29 LC322271J, M, T-70/80 This catalog provides information as of March, 1996. Specifications and information herein are subject to change without notice. n No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. n Anyone purchasing any products described or contained herein for an above-mentioned use shall: À Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: \` Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. n Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.