LB11620T SANYO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Features

  • Three-phase bipolar drive
  • Direct PWM drive (input of either a control voltage or a variable-duty PWM signal)
  • Built-in forward/reverse switching circuit
  • Full complement of protection circuits (current limiter, low-voltage, and automatic recovery lock (motor constraint) protection circuits)
  • Selectable Hall sensor signal pulse output Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage 1 V CC max V CC pin 18 V Output current I O max UL, VL, WL, UH, VH, WH pins 30 mA Allowable power dissipation Pd max *Mounted on a circuit board. 0.8 W Operating temperature Topr -20 to +100 °C Storage temperature Tstg -55 to +150 °C * Mounted on a circuit board : 114.3mm×76.1mm×1.6mm, glass epoxy board. Monolithic Digital IC Brushless Motor Driver

No.A0662-2/11 Recommended Operating Ranges at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage range 1-1 V CC1-1 V CC pin 8 to 17 V Supply voltage range 1-2 V CC1-2 V CC pin, with VCC shorted to VREG 4.5 to 5.5 V Output current I O UL, VL, WL, UH, VH, WH pins 25 mA

5 V constant voltage output current IREG -30 mA

HP pin voltage VHP 0 to 17 V HP pin output current IHP 0 to 15 mA RD pin voltage VRD 0 to 17 V RD pin output current IRD 0 to 15 mA Electrical Characteristics at Ta = 25°C, VCC = 12V Ratings Parameter Symbol Conditions min typ max Unit Supply voltage 1 I CC1 12 16 mA 5V constant voltage output (VREG pin) Output voltage VREG 4.7 5.0 5.3 V Line regulation ΔVREG1 V CC = 8 to 17V 40 100 mV Load regulation ΔVREG2 I O = -5 to -20mA 10 30 mV Temperature coefficient ΔVREG3 Design target 0 mV/ °C Low-voltage protection circuit (VREG pin) Operating voltage VSDL 3.5 3.7 3.9 V Clear voltage VSDH 3.95 4.15 4.35 V Hysteresis ΔVSD 0.3 0.45 0.6 V Output Block Output voltage 1-1 V OUT1-1 Low level I O = 400μA 0.2 0.5 V Output voltage 1-2 V OUT1-2 Low level I O = 10mA 0.9 1.2 V Output voltage 2 V OUT2 High level I O = -20mA V CC-1.1 V CC-0.9 V Output leakage current I Oleak 10 μA Hall Amplifier Block Input bias current IHB (HA) -2 -0.5 μA Common-mode input voltage range 1 VICM1 When a Hall effect sensor is used 0.5 V CC-2.0 V Common-mode input voltage range 2 VICM2 For single-sided input bias (Hall IC application)

0 V CC V

Hall input sensitivity 80 mVp-p Hysteresis ΔVIN (HA) 15 24 40 mV Input voltage low → high VSLH (HA) 5 12 20 mV Input voltage high → low VSHL (HA) -20 -12 -5 mV PWM Oscillator (PWM pin) High-level output voltage V OH (PWM) 2.75 3.0 3.25 V Low-level output voltage V OL (PWM) 1.2 1.35 1.5 V External capacitor charge current ICHG VPWM = 2.1V -120 -90 -65 μA Oscillator frequency f (PWM) C = 2000pF 22 kHz Amplitude V (PWM) 1.4 1.6 1.9 Vp-p Continued on next page

No.A0662-3/11 Continued from preceding page. Ratings Parameter Symbol Conditions min typ max Unit EI+ pin Input bias current IB (CTL) -1 1 μA Common-mode input voltage range VICM 0 VREG-1.7 V Input voltage 1 VCTL1 Output duty 100% 3.0 V Input voltage 2 VCTL2 Output duty 0% 1.35 V Input voltage 1L VCTL1L Design target value. When VREG = 4.7V, 100% 2.82 V Input voltage 2L VCTL2L Design target value. When VREG = 4.7V, 0% 1.29 V Input voltage 1H VCTL1H Design target value. When VREG = 5.3V, 100% 3.18 V Input voltage 2H VCTL2H Design target value. When VREG = 5.3V, 0% 1.44 V HP pin Output saturation voltage VHPL I O = 10mA 0.2 0.5 V Output leakage current IHPleak V O = 18V 10 μA CSD oscillator (CSD pin) High-level output voltage V OH (CSD) 2.7 3.0 3.3 V Low-level output voltage V OL (CSD) 0.7 1.0 1.3 V External capacitor charge current ICHG1 VCSD = 2V -3.15 -2.5 -1.85 μA External capacitor discharge current ICHG2 VCSD = 2V 0.1 0.14 0.18 μA Charge/discharge current ratio RCSD Charge current /discharge current 15 18 21 Times RD pin Low-level output voltage VRDL I O = 10mA 0.2 0.5 V Output leakage current IL (RD) V O = 18V 10 μA Current limiter circuit (RF pin) Limiter voltage VRF RF -GND 0.225 0.25 0.275 V PWMIN pin Input frequency f (PI) 50 kHz High-level input voltage V IH (PI) 2.0 VREG V Low-level input voltage V IL (PI) 0 1.0 V Input open voltage V IO (PI) VREG-0.5 VREG V Hysteresis V IS (PI) 0.2 0.25 0.4 V High-level input current I IH (PI) VPWMIN = VREG -10 0 10 μA Low-level input current I IL (PI) VPWMIN = 0V -130 -90 μA F/R pin High-level input voltage V IH (FR) 2.0 VREG V Low-level input voltage V IL (FR) 0 1.0 V Input open voltage V IO (FR) VREG-0.5 VREG V Hysteresis V IS (FR) 0.2 0.25 0.4 V High-level input current I IH (FR) -10 0 10 μA Low-level input current I IL (FR) -130 -90 μA N1 pin High-level input voltage V IH (N1) 2.0 VREG V Low-level input voltage V IL (N1) 0 1.0 V Input open voltage V IO (N1) VREG-0.5 VREG V High-level input current I IH (N1) VN1 = VREG -10 0 10 μA Low-level input current I IL (N1) VN1 = 0V -130 -100 μA

No.A0662-4/11 Package Dimensions unit : mm (typ) 3260A Pin Assignment

  • Three-Phase Logic Truth Table (IN = “H” indicates the state where IN+ > IN-) F/R = “L” F/R=“H” Output IN1 IN2 IN3 IN1 IN2 IN3 PWM

1 H L H L H L VH UL

2 H L L L H H WH UL

3 H H L L L H WH VL

4 L H L H L H UH VL

5 L H H H L L UH WL

6 L L H H H L VH WL

  • PWMIN pin Input state State High or open Output off Low Output on If the PWM pin is not used, the input must be held at the low level.
  • N1 pin Input state HP output High or open Three Hall sensor synthesized output Low Single Hall sensor output SANYO : TSSOP24(225mil) 6.4 0.5 4.4 (0.5) (1.0) 6.5 0.5 0.151 12 24 13 0.22 0.08 1.2max 0.8 0.32 0.4 1.2 – 20 80 100 6020 4001 2 0 Ambient temperature, Ta – °C Allowable power dissipation, Pd max – W Pd max – Ta Specified circuit board : 114.3×76.1×1.6mm3 glass epoxy board Mounted on a circuit board 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 LB11620T IN1+ IN2- IN2+IN1-ULUHVLVHWLWHRFGND PWM IN3 + IN3-RDCSDPWMINF/RHPN1EI+VREGVCC

No.A0662-5/11 Pin Functions Pin No. Pin Description

1 GND Ground

2 RF Output current detection. The cu rrent detection resistor (Rf) voltage is sensed by the RF pin to implement current detection. The maximum output current is set by RF to be IOUT = 0.25/Rf. UH VH WH Outputs (PWM outputs). These are push-pull outputs. UL VL WL Outputs These are push-pull outputs. 10, 9 12, 11 14, 13 IN1+, IN1- IN2+, IN2- IN3+, IN3- Hall sensor inputs from each motor phase. The logic high state indicates that IN+ > IN-. If inputs are provided by a Hall effect sensor IC, the common-mode input range is expanded by biasing either the + or - input. 15 PWM Functions as both the PWM oscillator frequency sett ing pin and the initial reset pulse setting pin. Connect a capacitor between this pin and ground. 16 RD Lock (motor constrained) detectio n state output. This output is turned on when the motor is turning and off when the lock protection function detects that the motor has been stopped. Th is is an open collector output. 17 CSD Sets the operating time fo r the lock protection circuit. Connect a capacitor between this pin and ground. Connec t this pin to ground if the lock protection function is not used. 18 PWMIN PWM pulse signal input. The output goes to the drive state when this pin is low, and to the off state when this pin is high or open. To use this pin for contro l, a CTL amplifier input such that the TOC pin voltage goes to the 100% duty state must be provided.

19 F/R Forward/reverse control input

20 HP Hall signal output (HP output). This provides either a single Hall sensor output or a synthesized 3-sensor output.

21 N1 Hall signal output (HP output) selection

22 EI+ CTL amplifier + (noninverting) input. The PWMIN pi n must be held at the low level to use this input for motor control 23 VREG 5V regulator output (Used as the control circuit pow er supply. A low-voltage protection circuit is built in.) Connect a capacitor between this pin and ground for stabilization. 24 V CC Power supply. Connect a capacitor between this pin and ground to prevent noise and other disturbances from affecting this IC.

No.A0662-6/11 Hall Sensor Signal Input/Output Timing Chart F/R = " L " IN1 IN2 IN3 UH UL VL WL WH VH F/R = " H " IN1 IN2 IN3 UH UL VL WL Sections shown in gray are PWM output periods. WH VH

No.A0662-7/11 Block Diagram and Application Example 1 Bipolar transistor drive (high side PWM) using a 5V power supply VM GND VCC RF WL VL UL UH VREG VCC VH WH IN3+ CTL VREG HP EI+ PWM PWMN PWM OSC PWM IN PRI DRIVER CURR LIM CONTROL LOGIC VREGLVSD COMP CSD OSCRD F/R N1 HP LOGIC HALL HYS AMP IN2+IN1+IN1F/R IN3 -IN2-IN1- VREG RD CSD HALL LOGIC

No.A0662-8/11 Application Example 2

54 MOS transistor drive (low side PWM)

using a 12V single-voltage power supply VM(12V) GND TR TR TR VCC RF WL VL UL UH VREG VCC VH WH IN3+ VREG HP EI+ PWM PWMN PWM OSC PWM IN PRI DRIVER CURR LIM CONTROL LOGIC VREGLVSD COMP CSD OSCRD F/R N1 HP LOGIC HALL HYS AMP IN2+IN1+IN1F/R IN3 -IN2-IN1- VREG RD CSD HALL LOGIC

No.A0662-9/11 Application Example 3 MOS transistor drive (low side PWM) using a VCC = 12V , VM = 24V power supply system VCC(12V) GND VCC RF WL VL UL UH VREG VCC VH WH IN3+ VREG HP EI+ PWM PWMN + VM(24V) PWM OSC PWM IN PRI DRIVER CURR LIM CONTROL LOGIC VREGLVSD COMP CSD OSCRD F/R N1 HP LOGIC HALL LOGIC HALL HYS AMP IN2+IN1+IN1F/R IN3 -IN2-IN1- VREG RD CSD

No.A0662-10/11 Application Example 4 MOS transistor drive (low side PWM) using a 24V single-voltage power supply GND VCC RF WL VL UL UH VREG VCC VH WH IN3+ VREG HP EI+ PWM PWMN VM(24V)+ PWM OSC PWM IN PRI DRIVER CURR LIM CONTROL LOGIC VREGLVSD COMP CSD OSCRD F/R N1 HP LOGIC HALL LOGIC HALL HYS AMP IN2+IN1+IN1F/R IN3 -IN2-IN1- VREG RD CSD

PS No.A0662-11/11 SANYO Semiconductor Co.,Ltd. assumes no responsib ility for equipment failures that result from using products at values that exceed, even momentarily, rate d values (such as maximum ra tings, operating condition ranges, or other parameters) listed in products specif ications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-qual ity high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to acci dents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause dam age to other property. When designing equipment, adopt safety measures so that these kinds of accidents or e vents cannot occur. Such measures include but are not limited to protective circuits and error prevention c ircuits for safe design, redundant design, and structural design. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable f or any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. Information (including circuit diagr ams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equi pment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. In the event that any or all SANYO Semiconductor C o.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any in formation storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. This catalog provides information as of February, 2 007. Specifications and information herein are subject to change without notice.