KPSG-100

KPSG100 KINGSTATE | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 5

Technical content

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 2/5 KPSG100 A. SCOPE 範疇 This specification applies piezoelectric diaphragm, KPSG100 此規格書適用於壓電式蜂鳴片, KPSG100 B. SPECIFICATION 規格 No. Item Unit Specification Condition 1 Max. input voltage 最大輸入電壓 V p-p MAX. 30

2 Resonant frequency

共振頻率 KHz 1.2 ± 0.2 The resonant frequency is suitable only for piezo element without wire. 共振頻率僅適用於蜂嗚片不加線材時之量測

3 Resonant impedance

共振阻抗 ohm MAX. 3,500 The resonant resistance is suitable only for piezo element without wire. 共振阻抗僅適用於蜂嗚片不加線材時之量測

4 Electrostatic capacity

靜電容量 pF 65,000 ± 30% at 120Hz/1V 5 Operating temp. 操作溫度 ℃ -20 ~ + 70 6 Storage temp. 儲存溫度 ℃ -20 ~ +70

7 Dimension

尺寸 mm φ50.0 x H 2.2 See appearance drawing 請參照外觀尺寸圖

8 Weight (MAX)

重量 gram 3.0

9 Material

材質 PIEZDELECTRO BUZZER ELEMENT： BRASS CASE：ABS UL-94 1/16” HB（BLACK）

10 Terminal

端子 Wire type Environmental Protection Regulation 環保法規 RoHS C. APPEARANCE DRAWING 外觀尺寸圖 Red Black UL1571 LF 30AWG Tol : ± 0.5 Unit: mm

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 3/5 KPSG100 D. MEASURING METHOD 測量方法 1. Resonant frequency / Resonant impedance 共振頻率/共振阻抗 Piezoelectric diaphragm shall be clamped at a node point as shown in following figure to be free from any mechanical stress, and measured its resonant frequency and resonant impedance by using vector impedance analyzer or equivalent. When the input frequency is swept within 100 Hz to 4 KHz, the resonant frequency is defined the frequency where the impedance shows minimum value, and this impedance shell be the resonant impedance 將壓電式振動片之節點夾住,如下圖,在無任何機械壓力狀況下,以交流阻抗分析儀測量其共振頻率及共振阻抗. 以掃頻的方式輸入100Hz ~ 4KHz頻率,共振頻率為阻抗最低的那一點,且此阻抗即共振阻抗. 2. Static capacitance 靜電容量 or equivalent. The part shall be clamped in the same way as the measurement of resonant frequency/ resonant impedance mentioned in the above. 以HP4194A測量在120 Hz時振動片的靜電容量. 夾住振動片方式與上述測共振頻率及共振阻抗的夾法相同.

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 4/5 KPSG100 E. MECHANICAL CHARACTERISTICS 機械特性 No. Item Test Condition Evaluation standard Solderability 焊錫附著性 (Connector excepted) 端子類不適用此項 Stripped wires of lead wires are immersed in rosin for 5 seconds and then immersed in solder bath of +270±5℃ for 3±0.5 seconds. 裸線部份浸入松香溶液5秒後,再浸入+270±5℃溶融焊鍚槽3±0.5秒. 90% min. stripped wires shall be wet with solder.(Except the edge of terminal) 浸入裸線部份附著焊鍚90%以 上.(末端斷面不算).

2 Lead Wire Pull Strength

線材拉力 The pull force shall be applied to double lead wire： Horizontal 3.0N(0.306kg) for 30 seconds. 雙線材水平方向施以3.0N(0.306kg)的力量,30秒. No damage and cutting off. 線材不鬆動,不脫落.

3 Vibration

振動試驗 Diaphragm shall be measured after being applied vibration of amplitude of 1.5mm with 10 to 55Hz band of vibration frequency to each of 3 per-pendicular directions for 2 hours. 振動週波數10～55HZ、全振幅1.5mm於 X.Y.Z 3個方向,各2 小時 The value of resonant frequency should be in ±10%, electrostatic capacity should be ±20%, which is compared with initial ones. The resonant impedance should be in Specification value. 與試驗前相較, 試驗後的共振頻 率變化量須在±10%內, 靜電容量 須在±20%內,共振阻抗須在規格 值內. F. ENVIRONMENT TEST 環境測試 No Item Test Condition Evaluation standard 1 High temp. test 高溫測試 After being placed in a chamber at +70℃ for 240 hours 置於+70℃環境中240小時 2 Low temp. test 低溫測試 After being placed in a chamber at –20℃ for 240 hours 置於-20℃環境中240小時

3 Humidity test

相對濕度測試 After being placed in a chamber at +40℃ and 90±5% relative humidity for 240 hours 置於+40℃, 相對濕度 90±5% 環境中240小時 4 Temp. cycle test 溫度循環試驗 The part shall be subjected to 5 cycles. One cycle shall be consist of:: 單體承受溫度循環測試5 次,其循環內容如圖示: + 7 0 ℃ + 2 5 ℃ + 2 5 ℃ - 2 0 ℃ 3hours Being placed for 4 hours at +25℃, diaphragm shall be measured The value of resonant frequency should be in ±10%, electrostatic capacity should be ±20%, which is compared with initial ones . The resonant impedance should be 2000 ohm max 經測試後, 靜置於+25℃（室溫） 環境中4 小時後 , 與試驗前相較, 試驗後的共振頻率變化量須在 ±10%內, 靜電容量須在±20%內, 共振阻抗為2000ohm以下 TEST CONDITION. Standard Test Condition : a) Temperature : +5 ~ +35 ℃ b) Humidity : 45-85% c) Pressure : 860-1060mbar 一般測試條件 : a) 溫度 : +5 ~ +35℃ b ) 濕度 : 45-85% c) 氣壓 : 860-1060mbar Judgement Test Condition : a) Temperature : +25 ± 2 ℃ b) Humidity : 60-70% c) Pressure : 860-1060mbar 爭議時測試條件 : a) 溫度 : +25 ± 2℃ b ) 濕度 : 60-70% c) 氣壓 : 860-1060mbar

志豐電子股份有限公司KINGSTATE ELECTRONICS CORP 5/5 KPSG100 G. PACKING STANDARD 包裝規格 330mm 375PCSx10=3750PCS 25PCSx15=375PCS Carton Box Out Box 550mmx330mmx290mm 310mmx248mmx49mm 550m m 290mm Carton Box (10PCS Out Box) Out Box Out Box 5x3x25PCS=375PCS