ILX75176 IKSEMICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Features
Low Quiescent Current: 300µA -7V to +12V Common-Mode Input Voltage Range Three-State Outputs 50ns Propagation Delays, 5ns Skew Half-Duplex Versions Available Operate from a Single 5V Supply Allows up to 32 Transceivers on the Bus Data rate: 10 Mbps Current-Limiting and Thermal Shutdown for Driver Overload Protection Enhanced ESD Specifications: ±15kV IEC61000-4-2 Air Discharge ±8kV IEC61000-4-2 Contact Discharge Pin Description ILX75176
ORDERING INFORMATION
Temperature Range Package Shipping ILX75176N TA = 0 to 70 C DIP8 Tube ILX75176D SOP8 Tube ILX75176DT SOP8 Tape & Reel
2012, February, ver. 01 ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC) 12V Continuous Power Dissipation (TA= +70°C) Control Input Voltage -0.5V to (VCC + 0.5V) 8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) 727mW Driver Input Voltage (DI) -0.5V to (VCC+ 0.5V) 8-Pin SOP (derate 5.88mW/°C above +70°C) 471mW Driver Output Voltage (A, B) -8V to +12.5V Operating Temperature Ranges 0°C to +70°C Receiver Input Voltage (A, B) -8V to +12.5V Storage Temperature Range -65°C to +150°C Receiver Output Voltage (RO) -0.5V to (VCC+0.5V) Lead Temperature (soldering, 10sec) +260°C * Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and function al operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2) PARAMETER SYMBOL CONDITIONS MIN TY P MAX UNIT S Differential Driver Output (no load) VOD1 5 V Differential Driver Output (with load) VOD2 R = 50Ω (RS-422) 2 V R = 27Ω (RS-485), Figure 1 1.5 5 Change in Magnitude of Driver Differential Output Voltage for Complementary Output States ∆VOD R = 27Ω or 50Ω, Figure 1 0.2 V Driver Common-Mode Output Voltage VOC R = 27Ω or 50Ω, Figure 1 3 V Change in Magnitude of Driver Common-Mode Output Voltage for Complementary Output States ∆VOD R = 27Ω or 50Ω, Figure 1 0.2 V Input High Voltage VIH DE, DI, RE 2.0 V Input Low Voltage VIL DE, DI, RE 0.8 V Input Current IIN1 DE, DI, RE ±2 µA Input Current (A, B) IIN2 DE = 0V; VIN = 12V 1.0 mA VCC = 0V or 5.25V VIN = -7V -0.8 Receiver Differential Threshold Voltage VTH -7V ≤ VCM ≤12V -0.2 0.2 V Receiver Input Hysteresis ∆VTH VCM = 0V 70 mV Receiver Output High Voltage VOH IO = -4mA, VID = 200mV 3.5 V Receiver Output Low Voltage VOL IO = 4mA, VID = -200mV 0.4 V
2012, February, ver. 01 DC ELECTRICAL CHARACTERISTICS (continue) (VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Three-State (high impedance) Output Current at Receiver IOZR 0.4V ≤ VO ≤ 2.4V ±1 µA Receiver Input Resistance RIN -7V ≤ VCM ≤ 12V 12 kΩ No-Load Supply Current (Note 3) ICC DE = VCC 500 900 RE = 0V or VCC 300 500 µA DE = 0V Driver Short-Circuit Current IOSD1 -7V ≤ VO ≤ 12V (Note 4) 35 250 mA VO = High Driver Short-Circuit Current IOSD2 -7V ≤ VO ≤12V (Note 4) 250 mA VO = Low Receiver Short-Circuit Current IOSR 0V ≤ VO ≤ VCC 7 95 mA ESD Protection A, B, Y and Z pins, tested using Human Body Model 15 kV SWITCHING CHARACTERISTICS (VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted.) (Notes 1, 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Driver Input to Output tPLH RDIFF = 54 10 55 60 ns tPHL CL1 = CL2 = 100pF 10 55 60 Driver Output Skew to Output tSKEW RDIFF = 54, CL1 = CL2 = 100pF 5 10 ns Driver Enable to Output High tZH CL= 100pF, S2 closed 40 70 ns Driver Enable to Output Low tZL CL= 100pF, S1 closed 40 70 ns Driver Disable Time from Low tLZ CL= 15pF, S1 closed 40 70 ns Driver Disable Time from High tHZ CL= 15pF, S2 closed 40 70 ns Receiver Input to Output tPLH RDIFF = 54 CL1 = CL2 = 100pF 20 60 100 ns tPHL 20 60 100 | tPLH - tPHL | Differential Receiver Skew tSKD RDIFF = 54 CL1 = CL2 = 100pF 5 10 ns Receiver Enable to Output Low tZL CRL = 15pF, S1 closed 30 50 ns Receiver Enable to Output High tZH CRL = 15pF, S2 closed 30 50 ns Receiver Disable Time from Low tLZ CRL = 15pF, S1 closed 30 50 ns Receiver Disable Time from High tHZ CRL = 15pF, S2 closed 30 50 ns Maximum Data Rate fMAX 2.5 10 20 Mbps Note 1: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. Note 2: All typical specifications are given for V CC=5V and TA=+25°C. Note 3: Supply current specification is valid for loaded transmitters when DE=0V. Note 4: Applies to peak current.
2012, February, ver. 01 Package Dimensions N SUFFIX PLASTIC DIP (MS – 001BA) Symbol MIN MAX A 8.51 10.16 B 6.1 7.11 C 5.33 D 0.36 0.56 F 1.14 1.78 G H J 0° 10° K 2.92 3.81 NOTE S: L 7.62 8.26 1. Dimensions “A”, “B” do not include mold flash or protrusions. M 0.2 0.36 Maximum mold flash or protrusions 0.25 mm (0.010) per side. N 0.38 D SUFFIX SOIC (MS - 012AA) Symbol MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G H J 0° 8° NOTE S: K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 1.27 5.72 Dimension, mm Dimension, mm 2.54 7.62 A BH C K C M J F M P G D R x 45 SEA TING PLANE 0.25 (0.010) M T -T- L H M J A B F G D SEATING PLANE N K 0.25 (0.010) M T -T- C