IL7101 INTEGRAL | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
GROUND FAULT INTERRUPTER EARTH IL7101 LEAKAGE CURRENT DETECTOR
Description
The IL7101N/D is designed for use in earth leakage circuit interrupters for operation directly off the AC Line in breakers. It contains pre regulator, main regulator, after regulator, differential amplifier, level comparator, latch circuit. The input in the differential amp latch circuit. The input in the differential amplifier is connect to the secondary node of zero current transformer. The level comparator generates high level when earth leakage current is greater than some level. Feature
- Low Power Consumption (PD=5mW) 100V/200V
- 100V/200V Common Built-in Voltage Regulator
- High Gain Differential Amplifier
- High Input Sensitivity
- Minimum External Parts ORDERING INFORMATION • Large Surge Margin IL7101N Plastic • Wide Operating Temperature Range (TА= -40 to 85°C) IL7101D SOIC • High Noise Immunity IL7101S SIP-8 • Meet U. L. 943 standards TA = -40° to 85° C for all packages. Absolute Maximum Ratings Supply Voltage 20V Supply Current 8mA 200m W - 40 to 85°C - 55 to 125°C Power Dissipation Operating Temperature Storage Temperature Pin Configuration (Top View) VR IN GND OS NR OD SC VR IN GND OS NR OD SC VR IN GND Os NR OD Sc
Recommended Operating Condition: TA=-30°C to 80°C PARAMETER SYMBOL MIN. TYP. MAX UNIT Supply Voltage V+ 12 V Vs-GND Capacitor Cvs 1 μF OS-GND Capacitor Cos 1 μF
Electrical Characteristics
PARAMETER SYMBOL CONDTIONS TEMP. (°C) MIN. TYP. MAX. UNIT -30 - - 580 25 - 400 530 Supply Current 1 lS1 V+=12V, VR - VI = 30 mV 85 - - 480 μA * Trip Voltage VT V+ = 16V, VR - VI = X -30 9 13.5 18 mV (rms) Differential Amplifier Output Current 1 ITD1 V+ = 16 V, VR - VI = 30 mV VOD = 1.2 V 25 -12 - -30 μA Differential Amplifier Output current 2 ITD2 V+ = 16 V, VR - VI = short VOD = 0.8 V 25 17 - 37 μA lSI = 580μA -30 -200 - lSI = 530μA 25 -100 - Output Current IO VSC = 1.4 V VOS = 0.8 V lSI = 480μA 85 -75 - μA SC ON Voltage VSC ON V+ = 16 V 25 0.7 - 1.4 V SC Input Current ISC ON V+ = l2V 25 - - 5 μA Output "L" Current IOSL V+ = 12 V, VOSL = 0.2 V -30 200 - - μA Input Clamp Voltage VIC V+ = 12 V, IIC = 20 mA -30 4.3 - 6.7 V Differential Input Clamp Voltage VIDC IIDC = 100mA -30 0.4 - 2 V Max. Current Voltage VSM ISM = 7 mA 25 20 - 28 V Supply Current 2 IS2 VOS = 0.5 V, VR - VI = X -30 - - 1200 μA Latch Circuit Off Supply Voltage V+ OFF 25 0.5 V Response Time TON V+ = 16 V, VR - VI = 0.3 V 25 1 - 4 ms
Typical Performance Curves
Supply voltage circuit is connected as a previous diagram. Please decide constants R1, R2, C4, and C5 of a filter in order to keep at least 12V in Vs, when normal supply current flows. In this case, please connect C4 (more than 1 ㎌) and C2 (less than 1 ㎌). ZCT and load resistance R L of ZCT are connected between input pin ① and ②. In this case protective resistance (R3=100Ω ) must be insulted. Sensitivity current is regulated by RL, and output of amplifier shows in pin④. External capacitor C1 between pin④ and GND is used for noise removal. When large current is grounded in the primary side (AC line) of ZCT, the wave form in the secondary side of ZCT is distorted and some signals doesn’t appear in the output of amplifier. So please connect a varistor or a diode (2pcs.) to ZCT in parallel. Latch circuit is used to inspect the output level of amplifier and to supply gate current on the external SCR. When input pin becomes more than 1.1V (Typ.) latch ci rcuit operates and supply gate current in the gate of SCR connected to the output pin⑦. Pin⑥ can be used in the open state, but please connect capacitor (about 0.047 ㎌) between pin⑥ and ⑦. Capacitor C6 between pin① and GND is used to remove noise and is about 0.047 ㎌.
(M S – 001BA) Sym b ol M I N M AX A 8.51 10.16 B 6.1 7.11 C 5.33 D 0.36 0.56 F 1.14 1.78 G H J 0° 10° K 2.92 3.81 NOTES: L 7.62 8.26 1. Dimensions “A”, “B” do not include mold flash or protrusions. M 0.2 0.36 Maximum mold flash or protrusions 0.25 mm (0.010) per side. N 0.38 D SU F F I X SOI C (MS - 012AA) Sym b ol M I N M AX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G H J 0° 8° NOTES: K 0.1 0.25 1. Dim ensions A and B do not include m old flash or protrusion. M 0.19 0.25 1.27 5.72 Dimens ion, mm Dimens ion, mm 2.54 7.62 A BH C K C M J F M P G D R x 45 SEA TING PLANE 0.25 (0.010) M T -T- L H M J A B F G D SEATING PLANE N K 0.25 (0.010) M T -T- C
A 6.24 6.60 B 0.40 0.54 b 1.15 1.40 C 0.23 0.35 D 19.68 20.20 E 2.675 2.925 e 2.54 L 2.95 3.25 L1 1.61 1.97 LQ 0.70 Z 1.21 Z1 1.40 8-Pin Plastic Single-in-Line (SIP) L Z B b Z 1 L Q D 1 8 e A E C R 0.125 M