IL2411N IKSEMICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
2011, March, Rev. 01 Tone Ringer The IL2411 is a bipolar integrated circuit designed for telephone bell replacement. Designed for Telephone Bell Replacement Low Current Drain Adjustable 2-frequency Tone Adjustable Warbling Rate Extension Tone Ringer Modules Alarms or Other Alerting Devices Adjustable for Reduced Supply Initiation Current. Built-in hysteresis prevents false triggering and rotary dial ‘Chirps’ SOP 8 DIP 8 TA = -45 to 65 C LOGIC DIAGRAM PIN 1 = VCC PIN 5 = GND 1. Output amplifier 2. High frequency oscillator 3. Low frequency oscillator 4. Hysteresis regulator (Regulator circuit has built-in hysteresis to prevent false triggering and rotary dial “Chirps”) PIN ASSIGNMENT V R CC LFI LF0 OUT HFI HF0 GND SL IL2411N/D
ORDERING INFORMATION
Temperature Range Package Packing IL2411N TA = -45 to 65 C DIP8 Tube IL2411D SOP8 Tube IL2411DT SOP8 Tape & Reel
2011, March, Rev. 01 PIN DESCRIPTION Name Pin Description VCC 1 Positive power supply. RSL 2 External resistor LFI 3 Input low frequency oscillator LF0 4 Output low frequency oscillator GND 5 Negative power supply HF0 6 High frequency oscillator output HFI 7 High frequency oscillator input Out 8 Tone output MAXIMUM RATINGS* Symbol Parameter Value Unit VCC DC Supply Voltage (Referenced to GND) to +30.0 V PD Power Dissipation in Still Air, Plastic DIP 400 mW Tstg Storage Temperature -65 to +150 C * Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit VCC DC Supply Voltage (Referenced to GND) 13.0 29.0 V TA Operating Temperature -45 +65 C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to th is high-impedance circuit. For proper operation, V IN and V OUT should be constrained to the range GND (VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC). Unused outputs must be left open.
2011, March, Rev. 01 ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND, TA = -20 to +70C) Guaranteed Limits Symbol Parameter Test Conditions Min Typ Max Unit VSI Initiation Supply Voltage (1) See Figure 1 16.8 21.2 V ISI Initiation Supply Current (1) 1.4 4.2 mA VSUS Sustaining Voltage (2) See Figure 1 9.5 12.2 V ISUS Sustaining Current (2) No Load VCC=VSUS See Figure 1 0.7 2.5 mA VOH High-Level Output Voltage VCC=21V, IOH=-15mA, Pin 6=6V, Pin 7=GND 16.7 21.0 V VOL Low-Level Output Voltage VCC=21V, IOL=15mA, Pin 6=GND, Pin 7=6V - 1.8 V IIN Maximun Input Leakage Current (Pin 3) Pin 3=6V,Pin 4=GND, VCC=21V - 1.0 A (Pin 7) Pin 7=6V,Pin 6=GND, VCC=21V - 1.0 A fH1 High Frequency 1 R3=191K,C3=6800pF 461 563 Hz fH2 High Frequency 2 R3=191K,C3=6800pF 576 704 Hz fL Low Frequency R2=165K,C2=0.47F 9.0 11.0 Hz Notes: 1. Initiation supply voltage (VSI) is the supply voltage required to start the tone ringer oscillating. 2. Sustaining voltage (VSUS) is the supply voltage required to maintain oscillation.
2011, March, Rev. 01 APPLICATION CIRCUIT F igure 3 APPLICATION NOTE The application circuit illustrates the use of the IL2411 devices in typical telephone or extension tone ringer application. The AC ringer signal voltage appears across the TIP and RING inputs of the circuit and is attenuated by capacitor C1 and resistor R1. C1 also provides isolation from DC voltages (48V) on the exchange line. After full wave rectification by the bridge diode, the waveform is filtered by capacitor C4 to provide a DC supply for the tone ringer chip. As this voltage exceeds the initiation voltage (VSI), oscillation starts. With the components shown, the ouptut frequency chops between 512(fh1) and 640Hz(fh2) at a 10Hz(fL) rate. The loudspeaker load is coupled through a 1300 to 8 transformer. The output coupling capacitor C5 is required with transformer coupled loads. When driving a piezo-ceramic transducer type load, the coupling C5 and transformer (1300:8) are not required. However, a current limiting resistor is required. The low frequency oscillator oscillates at a rate (fL) controlled by an external resistor (R2) and capacitor (C2). The frequency can be determined using the relation fL=1/1.289R2*C2. The high frequency oscillates at a fH1, fH2 controlled by an external resistor (R3) and capacitor (C3). The frequency can be determined using the relation Pin 2 allows connection of an external resistor RSL, which is used to program the solpe of the supply current vs supply voltage characteristics (see Fig2), and hence the supply current up to the initiation voltage ( VSI ). This initiation voltage remains constant independent of RSL. The supply current drawn prior to triggering varies inversely with RSL, decreasing for increasing value of resistance. Thus, increasing the value of RSL will decrease the amount of AC ringing current required to trigger the device. As such, longer sucribser loops are possible since less voltage is dropped per unit length of loop wire due to the lower current level. RSL can also be used to compensated for smaller AC couplin capacitors (C5 on Fig 3) (higher impedance) to the line which can be used to alter the ringer equivalence number of a tone ringer circuit. The graph in Fig2 illustrates the variation of supply current with supply voltage. Three curves are drawn to show the variation of initiation current with RSL. Curve B( RSL=6.8K) shows the I-V characteristic for the IL2411 tone ringer. Curve A is a plot with RSL<6.8K and shows an increase in the current drawn up to the initiation voltageVSI. The I-V characteristic after initiation remains unchanged. Curve C illustrates the effect of increasing RSL above 6.8K initiation current decreases but again current after triggering is unchanged.
2011, March, Rev. 01 N SUFFIX PLASTIC DIP (MS – 001BA) Symbol MIN MAX A 8.51 10.16 B 6.1 7.11 C 5.33 D 0.36 0.56 F 1.14 1.78 G H J 0° 10° K 2.92 3.81 NOTE S: L 7.62 8.26 1. Dimensions “A”, “B” do not include mold flash or protrusions. M 0.2 0.36 Maximum mold flash or protrusions 0.25 mm (0.010) per side. N 0.38 D SUFFIX SOIC (MS - 012AA) Symbol MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G H J 0° 8° NOTE S: K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 1.27 5.72 Dimension, mm Dimension, mm 2.54 7.62 A BH C K C M J F M P G D R x 45 SEA TING PLANE 0.25 (0.010) M T -T- L H M J A B F G D SEATING PLANE N K 0.25 (0.010) M T -T- C