IAM-93516 AVAGO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Features

  • DC =5V @ 111mA (Typ.)
  • RF =1.91 GHz, PinRF = -10 dBm;
  • LO =1.7 GHz, PinLO = 0 dBm;
  • IF = 210 MHz unless otherwise specified
  • High Linearity: 23.1 dBm IIP3(typ)
  • Conversion Gain: 9.4 dB typical
  • Low Noise Figure: 11.6 dB
  • Wide band operation:
  • 400-3000 MHz RF & LO input
  • 70 – 300 MHz IF output
  • Fully differential or single ended operation
  • High P1dB: 19.3 dB typical
  • Consistent RF performance over LO Power
  • Low current consumption: 5V@ 111mA typical
  • Excellent uniformity in product specifications
  • 3mm x 3mm x 0.9mm LPCC package
  • MTTF > 300 years[1]
  • MSL-1 and Lead-free.

Applications

  • Frequency down converter for base station radio card, microwave link transceiver, and MMDS
  • Modulation and demodulation for receiver
  • General purpose resistive FET mixer for other high linearity applications IAM - 93516 High Linearity Integrated GaAs Mixer Data Sheet

1.0 Absolute Maximum Ratings [1]

2.0 Product Consistency Distribution Charts [5,6]

  1. Operation of this device above any one of these parameters may cause permanent damage.
  2. Determined at DC quiescent conditions and TA = 25°C.
  3. Board (package belly) temperature TB is 25°C. Derate 25 mW/°C for TB > 130 °C.
  4. Channel-to-board thermal resistance measured using Infra Red Imaging Method and 150o C Liquid Crystal Measurement method.
  1. Distribution data sample size is 510 samples taken from 3 different wafers lots. Future wafers allocated to this product may have nominal val-

ues anywhere between the upper and lower limits.

  1. Measurements were made on a production test board, which represents a trade-off between optimal Gain, IIP3, NF, P1dB and isolation. Board

plied s-parameter file is also compensated. The total IF amplifier output loss is 0.67dB.

  1. The device current is measured without LO signal. At LO=0dBm, the current reduces by around 6 to 7mA.
  2. Gain, P1dB, isolation and return loss test conditions: FRF =1.91GHz, FLO = 1.7GHz, FIF = 210MHz, PinRF = -10dBm, PinLO = 0dBm.

IIP3 test condition: FRF1 = 1.91GHz, FRF2 = 1.89GHz, FLO = 1.7GHz, PinRF = -10dBm, PinLO = 0dBm.

3.0 IAM-93516 Electrical Specifications[6,8]

4.0 IAM-93516 Typical Performance[9,10]

Figure 4. IAM-93516 demoboard schematic optimally tuned at FRF = 1.91GHz and FLO = 1.7GHz Symbol Parameter and Test Condition Units Min. Typ Max.

5.0 IAM-93516 Typical Harmonic Suppresion Table[12,13]

6.0 IAM-93516 Pin Description

Figure 21. Harmonic Suppresion Table 5 VDD1 DC Power supply for the mixer circuit. differential or single ended. 14 VDD2 DC Power supply for the IF amplifier circuit.

  1. The harmonic suppression table shows the spurious signals present due to the mixing of the RF and LO at down conversion mode.

d. LO Harmonics are referenced to the signal level of the LO signal at 1.7GHz at the IF amplifier output.

PCB layout and Stencil Design LPCC 3x3 Package Dimensions Bottom ViewTop View Side View A3A1 A E D E D k eINDEX AREA (D/2 X E/2) SEATING PLANE e DIMENSIONS ARE IN MILLIMETERS 1GL 3X3-0.50 MIN. 0.80 2.90 1.70 2.90 1.70 0.20 NOM. 0.90 3.00 1.80 3.00 1.80 0.50 BSC. 0.02 0.20 REF. MAX. 1.00 3.10 1.90 3.10 1.90 0.05 REF. A D E e k PACKAGE

0.3±0.05 3.3±0.1 1.55±0.1 1.6±0.1 R 0.3 Typical 1.55±0.05 2.0±0.1 [1] 4.0±0.1 [2] 1.75±0.1 5.5±0.1[1] 12.0±0.3 3.3±0.18.0±0.1 Note: I. Measured from centerline of sprocket hole to centerline of pocket. II. Cumulative tolerance of 10 sprocket hole is ± 0.20 . III. Measured from centerline of sprocket hole to centerline of pocket. IV. Other material available. V. All dimension in millimeter unless otherwise stated.

Part Number No. Of Devices Container IAM-93516-TR1 1000 7” Reel IAM-93516-TR2 5000 13” Reel IAM-93516-BLK 100 Antistatic Bag Part Number Ordering Information For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. 5989-2800EN - March 29, 2006