DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 34
Technical content
SPEC. NUMBER S864-1470 PRODUCT GROUP REV. ISSUE DATE PAGE TITLE : HV070WS1-105 Product Specification A4(210 X 297) PAGE HYDIS Technologies OF 342012.12.20BTFT LCD PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HYDIS AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST
REVISION HISTORY
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED 0 Initial Release 2012.04.10 J.H. Kim A E1206- F005 Add Line Classification on Module Label No.3 (TOC: T, IDS: C) 2012.06.25 T.C.KANG B E1212- F001 Change Module Barcode Label
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
Contents
1.0 General Description 4
2.0 Absolute Maximum Ratings 6
3.0 Electrical Specifications 7
4.0 Optical Specifications 8
5.0 Interface Connections 13
6.0 Signal Timing Specifications 16
7.0 Signal Timing Waveforms 16
8.0 Input Signals, Basic Display Co lors & Gray Scale of Colors 19
9.0 3-Wire Special Port In terface (SPI Interface) 19
10.0 Power Sequence 26
11.0 Mechanical Characteristics 27
12.0 Mechanical Drawing 28
13.0 Reliability Test 30
14.0 Handling & Cautions 31
15.0 Labels 32
16.0 Packing Information 34
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
1.0 GENERAL DESCRIPTION
1.1 Introduction
HV070WS1-105 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 7.01 inch diagonally measured active area with WSVGA resolutions (1024 horizontal by 600 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is a low reflection and higher color type.
1.2 Features
FAB site : Hydis Korea Thin and Light Weight 3.3 V Logic Power & 16 V Back-light power Supply 1 Channel LVDS Interface SMD LED (20EA) Array (Bottom Side/Horizontal Direction) 16.7M Colors (With Dither & HFRC) Need SPI control (CSB, SCL, SDA) for module driving Green Product (RoHS) & Halogen free BL-PWM-OUT VCC TFT LCD Panel 1024 ×600 Gate Driver DC/DC Gamma Vcom Back Light (SMD LED Array) CN2 Source Driver LDO VDD LEDP & LEDN CN1 BL-PWM-IN LVDS Input Signal Vendor[0] Vendor[1] Ground VCC
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
1.4 General Specifications
Parameter Specification Unit Remark Active area 153.6(H) ×90.0(V) mm Number of pixels 1024(H) ×600(V) pixels Pixel pitch 0.15(H) ×0.15(V) mm Pixel arrangement RGB Vertical Stripe Display colors 16.7M colors Note 1 Display mode Normally Black Weight 95 (Max.) g Back-light Bottom edge side, 20-LEDs type Note 1 : Support 16.7M with dither and HFRC Note 2 : Without component Horizontal outline dimension is some different to customer request which is But outline dimension is confirm value between Hydis and Customer
1.3 Application
E-book, etc < Table 1. General Specifications >
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 Operating Range Storage Range -40 -20 0 20 40 60 80 Temperature (℃) (40, 90) (50, 50) (60, 27) 100 Relative Humudity (70, 20)
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. Parameter Symbol Min. Max. Unit Remarks Logic Power Supply Voltage V CC -0.3 V CC+0.3 V Back-light Power Supply Voltage V L -0.3 40 V Back-light LED Current I L - 30 mA Note 1 Back-light LED Reverse Voltage VR -5 V Operating Temperature T OP -20 +60 ℃ Note 1, Note 2Storage Temperature T SP -40 +70 ℃ Note 1. Ambient temperature vs allowable forward current are shown in the figure below. Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40℃ ≥ Ta) Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation. Ta=25+/-2°C < Table 2. Absolute Maximum Ratings >
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications
Parameter Min. Typ. Max. Unit Remarks Logic Power Supply Voltage V CC 3.0 3.3 3.6 V Note 1Logic Power Supply Current I CC - 220 270 mA Logic Power Consumption P C 0.73 0.89 W Back-light Power Supply Voltage V L -1 6 1 7 V Note 2 Back-light Power Supply Current I L -2 0 2 5 m A Back-light Power Consumption P BL - 1.28 1.36 W Note 2, 4 High Level Differential Input Signal (VCM = 1.2V) VTH -- 0 . 1 V LVDS input Low Level Differential Input Signal V TL -0 . 1 - - V Input voltage range (singled-end) V IN 0- 2 . 4 V Differential input voltage ｜VID ｜ 0.1 - 0.6 V Differential input common mode voltage VCM (｜VID ｜/2) 2.4- (｜VID ｜/2) V Input Current V IN -10 - -10 μA Panel unit life time 50,000 - - Hrs Without BL,PCB Total Power Consumption Ptotal - 2.01 2.25 W Note 1,2,4 < Table 3. Electrical Specifications > Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The logic current draw and power consumption specified is for 3.3V at 25℃. a) Typ : Window XP pattern, b) Max : White pattern 2. The supply voltage is measured and specified at the interface connector of LCM. The Backlight current draw and power consumption specified is 16V at 25℃. The voltage and current value means value for chain. 3. PWM frequency and voltage level is fixed by customer. 4. Backlight power consumption is calculated value for reference (VL× IL × 4 chains). About maximum power of backlight is 17V × 20mA × 4 chains = 1.36W
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
4.0 OPTICAL SPECIFICATIONS
4.1 Overview
The test of optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 25 2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. VCC shall be 3.3+/- 0.3V at 25C. Parameter Symbol Condition Min. Typ. Max. Unit Remarks Viewing Angle range Horizontal Θ3 CR > 10 75 85 Deg. Note 1Θ9 75 85 Deg. Vertical Θ12 75 85 Deg. Θ6 75 85 Deg. Luminance Contrast ratio CR Θ = 0 640 800 - Note 2 Luminance of White 1 Points Y w Θ = 0 30 cd/m 2 Note 4340 400 - cd/m 2 White Luminance uniformity
9 Points ∆Y9 72 80 - % Note 5
Θ = 0 0.280 0.301 0.340 Note 3 Wy 0.310 0.330 0.370 Reproduction of color Red Rx Θ = 0 0.563 0.593 0.623 Ry 0.323 0.353 0.383 Green Gx 0.283 0.313 0.343 Gy 0.559 0.589 0.619 Blue Bx 0.121 0.151 0.181 By 0.099 0.129 0.159 Response Time Total (Tr +T d) Ta= 25 C Θ = 0 - 50 - ms Note 6 Cross Talk CT Θ = 0 - - 2.0 % Note 7
4.2 Optical Specifications
<Table 4. Optical Specifications>
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see Figure1). 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state (see Figure1). Luminance Contrast Ratio (CR) is defined mathematically as CR = Luminance when displaying a white raster / Luminance when displaying a black raster. 3. Reference only / Standard Front Surface Treatment Measured with green cover glass. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 4. The luminance value of 400 cd/m2 means the brightness of PWM is 100%. The luminance value of 30 cd/m2 means the brightness of lower PWM. CTF means that measure brightness at only center point at Figure 2.
Figure 1. Measurement Set Up Figure 2. Uniformity Measurement Locations (9 points)
4.3 Optical Measurements
Figure 3. Response Time Testing
Figure 4. Cross Modulation Test Description to change from 10% to 90% is Tr, and 90% to 10% is Td. driven dark (Refer to Figure 4).
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
5.0 INTERFACE CONNECTIONS
5.1 Electrical Interface Connection
CN1 Interface Connector (DF23C-30DS-0.5V(51), Manufacture by HIROSE) Pin No. Symbol Function 1 VCC +3.3V Power Supply
2 GND Ground
3 VCC +3.3V Power Supply
4 CLK-IN-N LVDS Clock input (Negative)
5 VCC +3.3V Power Supply
6 CLK-IN-P LVDS Clock input (Positive)
7 GND Ground
8 GND Ground
9 LEDP Power supply for LED [Anode]
10 D0-IN-N LDVS differential data input
11 LEDN Power supply for LED [Cathode]
12 D0-IN-P LDVS differential data input
13 GND Ground
14 GND Ground
15 Vendor[0] Vendor distinguish pin 1
<Table 5, Electrical Interface Connection > Pin No. Symbol Function
16 D1-IN-N LDVS differential data input
17 Vendor[1] Vendor distinguish pin 2
18 D1-IN-P LDVS differential data input
19 CSB Serial Communication Chip Select
20 GND Ground
21 SCL Serial Communication Clock Input
22 D2-IN-N LDVS differential data input
23 SDA Serial Communication Data Input
24 D2-IN-P LDVS differential data input
25 GND Ground
26 GND Ground
27 BL-PWM-IN Brightness Control Signal
28 D3-IN-N LDVS differential data input
29 BL-PWM-OUT Backlight Dimmer Signal
30 D3-IN-P LDVS differential data input
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
5.2 LVDS Interface
LVDS Transmitter : THC63LVDM83A Input signal Transmitter Interface AA01B- P030VA1 Remark Pin No Pin No System (Tx) TFT-LCD (Rx) Pin No. R0 51 OUT0- OUT0+ D0-IN-N D0-IN-P R1 52 R2 54 R3 55 R4 56 R5 3 G0 4 G1 6 OUT1- OUT1+ D1-IN-N D1-IN-P G2 7 G3 11 G4 12 G5 14 B0 15 B1 19 B2 20 OUT2- OUT2+ D2-IN-N D2-IN-P B3 22 B4 23 B5 24 HSYNC 27 VSYNC 28 DE 30 R6 50 OUT3- OUT3+ D3-IN-N D3-IN-P R7 2 G6 8 G7 10 B6 16 B7 18 Reserved 25 MCLK 31 40 CLKOUT- CLK-IN-N 4
39 CLKOUT+ CLK-IN-P 6
<Table 6, LVDS Interface >
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
5.4 Data Input Format
5.3 Back-light Interface
CN2 LED FPC Connector ( solder type ) Pin No. Symbol Function Remark Anode1 LED Anode Power Supply Typ. 16V Cathode1 LED Cathode Power Supply
4 LED Cathode Power Supply
1 Pixel = 3 Dots
<Table 7, LED FPC connection >
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 6.0. SIGNAL TIMING SPECIFICATIONS
6.1 Timing specification at HV Mode (LVDS Transmitter Input)
Item Symbol Min. Typ. Max. Unit Frame Rate - 40 60 73 Hz Frame Period T1 624 635 750 Lines Vertical Display Time T2 - 600 - Lines Vertical Blanking Time T3 - 35 - Lines
1 Line Scanning Time T4 1200 1344 1400 Clocks
Horizontal Display Time T5 - 1024 - Clocks Horizontal Blanking Time T6 - 320 - Clocks Clock Rate 1/T7 40.8 51.2 63 MHz <Table 8, Signal Timing > VSD … … …HSD T2T3
7.0 SIGNAL TIMING WAVEFORMS
7.1 Vertical Input Timing Waveforms of Interface Signal
7.2 Horizontal Input Timing Waveforms of Interface Signal
DEN … … HSD DCLK … … … … DEN
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
7.3 LVDS Rx Interface Timing Parameter
The specification of the LVDS Rx interface timing parameter < Table 9, LVDS Rx Interface Timing Specification> tRIP5 tRIP4 tRIP3 tRIP2 tRIP6 tRIP1 tRIP0 Rx Rx Rx Rx Rx Rx Rx Rx Rx RxRx tRCIP Vdiff=0[v]Vdiff=0[v]RxCLKIN+/- RxINz +/- * Z = 0, 1, 2 Item Symbol Min. Typ. Max. Unit Remarks CLKIN Period tRCIP - 19.53 - nsec Input Data 0 tRIP0 -0.4 0.0 +0.4 nsec Input Data 1 tRIP1 tRICP/7- 0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP2 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP3 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP5 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP6 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF
A total of 16.7M colors are displayed with dither & HFRC using 64 gray from 8bit input. Colors & Gray Scale Data signal Red data Green data Blue data R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 Basic Colors B l a c k 000000000000000000000000 B l u e 000000000000000011111111 G r e e n 000000001111111100000000 L i g h t B l u e 000000001111111111111111 R e d 111111110000000000000000 P u r p l e 111111110000000011111111 Y e l l o w 111111111111111100000000 W h i t e 111111111111111111111111 Gray Scale of Red B l a c k 000000000000000000000000 △ 100000000000000000000000 D a r k e r 010000000000000000000000 △ ↓↓↓ ▽ ↓↓↓ B r i g h t e r 101111110000000000000000 ▽ ↓ 0000000000000000 R e d 111111110000000000000000 Gray Scale of Green B l a c k 000000000000000000000000 △ 000000001000000000000000 D a r k e r 000000000100000000000000 △ ↓↓↓ ▽ ↓↓↓ B r i g h t e r 000000001011111100000000 ▽ 00000000 ↓ 00000000 G r e e n 000000001111111100000000 Gray Scale of Blue B l a c k 000000000000000000000000 △ 000000000000000010000000 D a r k e r 000000000000000001000000 △ ↓↓↓ ▽ ↓↓↓ B r i g h t e r 000000000000000010111111 ▽ 0000000000000000 ↓ B l u e 000000000000000011111111 Gray Scale of White & Black B l a c k 000000000000000000000000 △ 100000001000000010000000 D a r k e r 010000000100000001000000 △ ↓↓↓ ▽ ↓↓↓ B r i g h t e r 101111111011111110111111 ▽ ↓↓↓ W h i t e 111111111111111111111111
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 9.0 3-WIRE SERIAL PORT INTERFACE (SPI INTERFACE) This module use 3-wire serial port interface as function configuration and parameter setting D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D15 D14SDA CSB SCL Address[5:0] W/R Hi-Z Data[7:0] Delay Next Transfer 9.1 3-Wire command format Bit Description D15-D10 Register Address [5:0] D9 W/R control bit. “0” for Write; “1” for Read D9 Hi-z bit during read mode. Any data within this bits will be ignored during write Mode D7-D0 Data for the W/R operation to the address indicated by Address phase 9.2 3-Wire Write format MSB LS B D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D1 Register Address [5:0] 0 X Data (Issued by external controller) 9.3 3-Wire Read format MSB LS B D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D1 Register Address [5:0] 1 Hi-Z Data (Issued by 3-wire engine)
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 9.4 3-wire control register
9.4.1 R00 : System Control Register
Designation Address Description MODE R0[0] DE/SYNC mode select. MODE = “0”, HSD/VSD mode. MODE = “1”, DE mode. (Default) DCKPOL R0[1] DCLK polarity control bit DCLKPOL = “0” : Data sampling at DCLK falling edge. (Default) DCLKPOL = “1” : Data sampling at DCLK rising edge. GRB R0[2] Global reset bit. GRB=“0”, The controller is in reset state. GRB=“1”, Normal operation. (Default) STBYB R0[3] Standby mode selection bit. STBYB = “0”, Timing control, driver and DC-DC converter, are off, and all outputs are High-Z. STBYB = “1”, Normal operation. (Default) UPDN R0[4] Gate Up or Down scan control. UPDN = “0”, STV2 output vertical start pulse and UD pin output Logical “0” to Gate driver. (Default) UPDN = “1”, STV1 output vertical start pulse and UD pin output Logical “1” to Gate driver. (Default) SHLR R0[5] Right/Left sequence control of source driver. SHLR = “0”, Shift left : Last data = S1<-S2<-S3…<-S960 = First Data SHLR = “1”, Shift left : Last data = S1->S2->S3…->S960 = Last Data (Default) - R0[6] Reserved PWR_EN R0[7] POWER enable. PWR_EN = H, enable PWM, Charge pump and VCOM buffer.
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
9.4.2 R01 : System Control Register
Designation Address Description R1[0] Reserved RES[1:0] R1[2:1] Display resolution selection. RES[1:0] = “01”, for 1024(RGB)*768 display resolution. (dual or cascade) RES[1:0] = “00”, for 1024(RGB)*600 display resolution. (dual or cascade) (Default) RES[1:0] = “10”, for 800(RGB)*600 display resolution. (dual or cascade) RES[1:0] = “11”, for 800(RGB)*480 display resolution. (dual or cascade) (601~936 channel disable) BIST R1[3] Normal Operation / BIST pattern select. BIST = H : BIST (DCLK input is not needed) BIST = L : Normal Operation (Default) DITHER R1[4] Dithering function enable control. DITHER = “1”, Enable internal dithering function. DITHER = “0”, Disable internal dithering function. (Default) HFRC R1[5] H-FRC selection HFRC = H : H-FRC enable HFRC = L : H-FRC disable (Default) If DITHER = H and HFRC = L : enable only FRC/dithering function If DITHER = L, disable dithering function (H-FRC and FRC both disable) CABC_EN[1:0] R1[7:6] CABC H/W enable pin. Normally pull low. When CABC_EN = “00”, CABC OFF. (Default mode) When CABC_EN = “01”, User interface Image. When CABC_EN = “10”, Still Picture. When CABC_EN = “11”, Moving Image. Designation Address Description R2[5:0] Reserved NBW R2[6] Normally black or normally white setting. NBW = H : Normally black NBW = L : Normally white (Default) BIST R2[7] Reserved
9.4.3 R02 : System Control Register
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
9.4.4 R03 : Gate on sequence controller register
Designation Address Description SEL[1:0] R3[1:0] Gate on sequence select Frame R3[2] Frame inverse or not select. FRAME = “1”, Uniform FRAME = “0”, Frame inverse (Default) - R3[7:3] Reserved SEL[0] SEL[1] Pin control function 0 0 Z (Default)
9.4.5 R0E : test mode (1)
Designation Address Description TEST_mode(1) R0E[7:0] Enter test mode (1) TEST_mode = 8’h5F, enter TEST_mode = other exit (Default)
9.4.6 R0F : test mode (2)
Designation Address Description TEST_mode(2) R0F[7:0] Enter test mode (2) TEST_mode = 8’hA4, enter TEST_mode = other exit (Default)
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
9.4.7 R0D : charging time control (3)
Designation Address Description OE_WIDTH R0D[7:0] Inversion type select. Enter Test mode (1) and (2) first. Then R0D setting will be active TEST_mode = 8’h00, increase charge time
9.4.8 R02 : charge sharing control
Designation Address Description EQC_ADJ R02[7:0] Inversion type select. Enter Test mode (1) and (2) first. Then R10 setting will be active EQC_ADJ = 8’h43, adjust charge sharing time
9.4.9 R0A : BIAS current control (5)
Designation Address Description BIAS_TRIG R0A[7:0] Inversion type select. Enter Test mode (1) and (2) first. Then R10 setting will be active BIAS_TRIG = 8’h28, trigger bias reduction
9.4.10 R10 : inversion architecture
Designation Address Description INV R10F[7:0] Inversion type select. Enter Test mode (1) and (2) first. Then R10 setting will be active 2line / 1dot = 8’h41 1line / 1dot = 8’h01 (Default)
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34 R38[7:0] PWM_DIV[3:0] Register function 0x0C 000 Don’t use. 0x1C 001 1 0x2C 010 2 0x3C 011 3 0x4C 100 4 0x5C 101 5 0x6C 110 6 0x7C 111 7 (Default)
9.4.11 R38 : PWM_DIV setting
Designation Address Description PWM_DIV[3:0] R38[7:0] PWM Dimmer frequency step setting In order in maintain the dimming frequency for brightness control at different display resolution (typical 1024 x 600) at normal mode. We will change default value of PWM_DIV to follow as table Display Resolution Default value of PWM_DIV Note : The R6 and R38 register will be available when the R0E and R0F register already had issued. PWM Reference Frequency (FOSC) Real PWM Frequency of DIMO 51.2MHz (Typical) PWM Frequency = FOSC 256 x 128 x PWM_DIV[2:0]
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
9.5 Recommend Register Setting (CABC Off mode)
Register write sequence : R00 (Reset)R00 (Into Standby mode) R01 (Enable FRC / Dither, CABC off) R02 (Enable Normally Black) R0E (Enter Test mode (1)) R0F (Enter Test mode (2)) R0D (SDRRS on) R00 (Release standby mode) If you don’t use register write sequence, it may cause faulty operation. D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Setting Remark R 0 00 0 0 0 0 0 0000101001 0x0029 R 0 00 0 0 0 0 0 0000100101 0x0025 R 0 10 0 0 0 0 1 0000110000 0x0430 R 0 20 0 0 0 1 0 0001000000 0x0840 R 0 E0 0 1 1 1 0 0001011111 0x385F R 0 F0 0 1 1 1 1 0010100100 0x3CA4 R 1 00 1 0 0 0 0 0001000001 0X4041 2dot inv. R 0 D0 0 1 1 0 1 0000000001 0x3401 R 0 00 0 0 0 0 0 0000101101 0x002D
9.6 Recommend Register Setting (CABC on mode (Moving Picture)
Register write sequence : R00 (Reset)R00 (Into Standby mode) R01 (Enable FRC / Dither, CABC on) R02 (Enable Normally Black) R0E (Enter Test mode (1)) R0F (Enter Test mode (2)) R0D (SDRRS on) R38 (PWM Frequency = 1.5KHz) R00 (Release standby mode) If you don’t use register write sequence, it may cause faulty operation. D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Setting Remark R 0 0 000000 0 0 0 0101001 0x0029 R 0 0 000000 0 0 0 0100101 0x0025 R 0 1 000001 0 0 0 0110000 0x04F0 R 0 2 000010 0 0 0 1000000 0x0840 R 0 E 001110 0 0 0 1011111 0x385F R 0 F 001111 0 0 1 0100100 0x3CA4 R 1 0 010000 0 0 0 1000001 0X4041 2dot inv. R 0 D 001101 0 0 0 0000001 0x3401 R 3 8 111000 0 0 0 0011100 0xE01C R 0 0 000000 0 0 0 0101101 0x002D
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
10.0 POWER SEQUENCE
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below Power Supply for LCD VCC Interface Signal Vi (LVDS Signal of Transmitter) LED Power Valid Data T3 T4 90% 10% 90% 10% Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. Initial 3-Wire Command LED ON OFFOFF Parameter Value Unit Remark Min. Typ. Max. T1 0.5 10 ms T2 0 16 ms T3 200 ms T4 200 ms T5 0 ms T6 3 ms T7 400 ms
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
11.0 MECHANICAL CHARACTERISTICS
11.1 Dimensional Requirements
Figure 5 & 6 (located in 12.0) shows mechanical outlines for the model Parameter Specification Unit Active Area 153.60(H) X 90.00(V) mm Number of pixels 1024(H) X 600(V) (1 pixel = R + G + B dots) Pixel pitch 0.15(H) X 0.15(V) Pixel arrangement RGB Vertical stripe Display colors 16.7M Display mode Normally Black Weight 95 (Max.) g Back-light Edge side 20-LEDs type ( 5 X 4 Array) 11.2 Polarizer Hardness. The surface of the LCD has an coating to reduce scratching.
11.3 Light Leakage
There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable. <Table9, Mechanical Characters >
Figure 5. TFT-LCD Module Outline Dimension (Front View)
12.0 MECHANICAL DRAWING
Figure 6. TFT-LCD Module Outline Dimensions (Rear view)
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
13.0 RELIABLITY TEST
The Reliability test items and its conditions are shown in below. <Table10, Reliability Test> No Test Item Conditions
1 Temperature and Humidity test
(Operation) 1. Ta = 40℃/90% 24hr 2. Ta = 40℃/30% 24hr 3. Ta = 0℃ 24hr
2 Temperature and Humidity Cycling
(Storage) Ta = 85℃/90%RH (2H) ,-20℃(2H),Waypoint(25℃25% RH turn off Humidity control) 12cycle. 144Hr
3 Thermal shock Ta = -40 C 85 C
(30min residence), 100 cycle
4 Low temperature storage test Ta = -40 C, 300 hrs
5 Low Temperature Test (Operation) Ta = -20 C, 300hrs
6 Biased Humidity/Heat Soak Test
(Storage) Ta = 85 C /85%, 300hr
7 Altitude storage 20000 ft/-40 C, 24hr
8 Hot Start Test Ta = 85 C 1hr, power on/off per 5m, 5 time
9 Cold Start Test Ta = -40 C 1hr, power on/off per 5m, 5 time
10 Mechanical shock 100 G, 6 ms, half sine wave(±X,±Y,±Z). Acceleration measured shock table. 11 Mechanical Random vibration 3.5 Grms, PSD =0.025g2/Hz, 5-500 Hz 15 minutes in all axes (X, Y, Z) 12 4 Pt Bend Test 1. 7 kgf deflection. Scribed edge side up 2. 4 kgf deflection. Scribed edge side down 13 Ring on Ring Test X kgf applied. Load rae:75mm/min
14 ESD
Screen: 150 pF, 330 Ohm, +/-15kV air, +/- 8 kV contact. FPC: 100 pFm100 Ohm, +/-200V 10 points, 20times/pt
15 Functional Test Page flip script, 2 m flips
Notes : 1. Except form over the conditions of the polarizer specifications. 2. ESD test condition is standard of customer system.
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
14.0 HANDLING & CAUTIONS
14.1 Cautions when taking out the module
Pick the pouch only, when taking out module from a shipping package.
14.2 Cautions for handling the module
As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass (epoxy) material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care.
14.3 Cautions for the operation
When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged.
14.4 Cautions for the atmosphere
Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended.
14.5 Cautions for the module characteristics
Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking.
14.6 Cautions for the digitizer assembly
When assembling FPC connector, do not flip connector past 90° due to possible damage to connector. When positioning digitizer underneath driver IC, do not lift driver IC past 90° due to possible damage to drive IC pattern. Please be warned that during assembly of digitizer, the opening or closing of FPC will result in possible electrostatic discharge damage to the LED
14.7 Other cautions
Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages.
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
15.0 LABELS
15.1 Product Label
No 1. Control Number No 2. Rank / Grade No 3. Line Classification (Hydis: H, TOC: T, IDS: C) No 5. Month (1, 2, 3,…, 9, X, Y, Z) No 6. FG Code No 7. Serial Number No 4. Year (5 : 2005, 6 : 2006, …) XXXXXXXXXXXXXXXX X HYDIS Barcode 01~03 : Vendor code 04~14 : QPN 15~16 : Manufactured year 17~18 : Manufactured week 19~22 : Serial number (32 digit/alphabet) Customer Barcode YYVVV PPPPPPPPPPP WW ZZZZ HV070WS1-105 HYDAA070WS10081133ZZZZ MADE IN CHINA
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
15.2 Packing Label
Label Size: 108 mm (L) 56 mm (W) Model: HV070WS1-105 Q\ty: Module Q\ty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product MODEL : HV070WS1-105 SERIAL NO. : 0000000000000 Q’TY : 40 DATE : XXXX. XX. XX 00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no FG CODE RoHS Mark
PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT B 2012.12.20 SPEC. NUMBER S864-1470 SPEC TITLE HV070WS1-105 Product Specification PAGE OF 34
16.0 PACKING INFORMATION
16.1 Packing order
Notes : 1. Box Dimension: 350mm(W) X 265mm(D) X 320mm(H) 2. Package Quantity in one Box : 40pcs Anti Static Packing BAG 20EA Module per Inner-Box LCD Module Shield Bag Cushion PAD Top PAD Bottom PAD Out Box 40EA Module per Inner-Box Assy Packing Label