HSM6

HSM6 CONNOR-WINFIELD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation

2111 Comprehensive Drive

Aurora, Illinois 60505 Phone: 630-851- 4722 Fax: 630- 851- 5040 www.conwin.com Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630- 851- 5040 www.conwin.com 5.0V Surface Mount Crystal Clock Oscillator HSM6 XO The Connor-Winfield models HSM61, HSM62, and HSM63 are 7.5mm x 5mm, 5.0V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The RoHS compliant surface mount package is designed for high-density mounting and is optimum for mass production Operating Specifications Parameter Minimum Nominal Maximum Units Notes Frequency Range (Fo) 1.0 - 80 MHz Frequency Tolerance - ppm 1 HSM61 -25 25 HSM62 -50 50 HSM63 -100 100 Operating Temp Range -40 - 85 °C Supply Voltage (Vdd) 4.5 5.0 5.5 Vdc Supply Current (Icc) - - mA 1.8 to 31.999 MHz 27 32.0 to 49.999 MHz 45 50 to 80.0 MHz 75 Absolute Maximum Ratings Parameter Minimum Nominal Maximum Units Notes Storage Temperature -55 - 125 °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Features: RoHS Compliant 1.0 to 80 MHz 5.0V Operation Tri-State Enable/Disable Function Overall Frequency Tolerance: HSM61 ± 25 ppm, HSM62 ± 50 ppm, HSM63 ± 100 ppm Temperature Range: -40 to 85°C Ceramic Surface Mount Package Tape and Reel Packaging Notes: 1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Bulletin SM036 Page 1 of 2 Revision 13 Date 18 Dec 2007 US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Input Characteristics Parameter Minimum Nominal Maximum Units Notes Enable Voltage - (Vih) 2.2 - - Vdc 2 Disable Voltage - (Vil) - - 0.8 Vdc Enable Time - - 100 nS Disable Time - - 100 nS HCMOS Output Characteristics Parameter Minimum Nominal Maximum Units Notes Load - - 50 pF Voltage High (Voh) 4.50 - - VdcLow (Vol) - - 0.55 Current High (loh) -16 - - mALow (lol) - - 16 Duty Cycle at 50% of Vcc 45 50 55 % Rise / Fall Time 10% to 90% - - 5 nS Start-Up Time - - 10 mS Jitter - - 5 pS RMS

Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630- 851- 5040 www.conwin.com Bulletin SM036 Page 2 of 2 Revision 13 Date 18 Dec 2007 Pin Connections 1: Enable/Disable 2: Ground 3: Output 4: Vcc OSCILLOSCOPE FREQ COUNTER OSC POWER SUPPL Y INPUT FOR E/D PROBE Meets EIA-481A and EIAJ-1009B 2,000 PCS/Reel Bypass capacitor, C-by, should be ceramic capacitor ≥ .01 uf SYMMETRY Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Suggested Pad Layout

Ordering Information

Mechanical Characteristics Mechanical Shock MIL STD 883 Method 2002 Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90% Test Circuit Output Waveform Tape and Reel Dimensions Package Characteristics Package Hermetically sealed ceramic package and metal cover Dimensional Tolerance: ±.02"(.508mm) ±.005"(.127mm) HSM 6 1 044.736M Type: Temperature Range: Frequency Tolerance: Supply Voltage: Output Frequency: Clock 7.5x5.0mm Package 6 = -40 to 85˚C 1 = ± 25 ppm 2 = ± 50 ppm 3 = ± 100 ppm Omit = 5.0 Vdc Frequency Format -xxx.xM Minimum * -xxx.xxxxxxM Maximum* *Amount of numbers after the decimal point. M = MHz Example: To Order an HSM61 with an output frequency of: 4 MHz = HSM61-004.0M 44.736 MHz = HSM61-044.736M 125 MHz = HSM61-125.0M