HCPL-050L-500E

HCPL-050L AVAGO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

Features

• 3.3V/5V Dual Supply Voltages
• Low power consumption
• High speed: 1 Mb/s
• LVTTL/LVCMOS compatible
• Available in 8-pin DIP , SO-8
• Open collector output
• Guaranteed performance from temperature: 0˚C to +70˚C
• Safety approval, UL, CSA, IEC/EN/DIN EN 60747-5-2

Applications

• High voltage insulation
• Video signal isolation
• Power translator isolation in motor drives
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation – LVTTL/LVCMOS
• Replaces pulse transformers
• Replaces slow phototransistor isolators Functional Diagram A 0.1 µF bypass capacitor must be connected between pins 5 and 8. HCPL-250L Functional Diagram 4 5 8ANODE 1 CATHODE 1 CATHODE 2 ANODE 2 VCC VO1 VO2 GND HCPL–253L/HCPL–053L 4 5 8NC ANODE CATHODE NC VCC VB VO GND TRUTH TABLE (POSITIVE LOGIC) LED ON OFF VO LOW HIGH HCPL–250L/HCPL–050L HCPL-250L/050L/253L/053L LVTTL/LVCMOS Compatible 3.3 V Optocouplers (1 Mb/s) Data Sheet 8-Pin DIP SO-8 Package HCPL-250L HCPL-050L HCPL-253L HCPL-053L Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

Ordering Information

HCPL-250L, HCPL-253L, HCPL-050L and HCPL-053L are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 Quantity -000E no option 300 mil DIP-8 50 per tube -300E -300 X X 50 per tube -500E -500 X X X 1000 per reel HCPL-250L -020E -020 X 50 per tube HCPL-253L -320E -320 X X X 50 per tube -520E -520 X X X X 1000 per reel -060E -060 X 50 per tube -360E -360 X X X 50 per tube -560E -560 X X X X 1000 per reel HCPL-050L -000E no option SO-8 100 per tube HCPL-053L -500E -500 X X X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-253L-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-253L to order product of 300 mil DIP package in Tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant will use ‘–XXXE. ’

HCPL-250L/HCPL-050L HCPL-253L/HCPL-053L

1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) A XXXXZ YYWW DATE CODE DIMENSIONS IN MILLIMETERS AND (INCHES). 5678 4321 OPTION CODE* UL RECOGNITION UR TYPE NUMBER * MARKING CODE LETTER FOR OPTION NUMBERS "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005) Small Outline SO-8 Package XXXV YWW 8 7 6 5 4321 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.050)BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012)MIN. TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. OPTION NUMBER 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 0.203 ± 0.102 (0.008 ± 0.004) PIN ONE 0 ~ 7° 7.49 (0.295) 1.9 (0.075) 0.64 (0.025) LAND PATTERN RECOMMENDATION

Solder Reflow Temperature Profile Regulatory Information The devices contained in this data sheet have been ap - proved by the following organizations: UL Approval under UL 1577, Component Recognition Pro - gram, File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. Recommended Pb-Free IR Profile TIME (SECONDS) TEMPERATURE (°C) 200 100 50 150100 200 250 300 SEC. 50 SEC. SEC. 160°C 140°C 150°C PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C SOLDERING TIME 200°C PREHEATING TIME 150°C, 90 + 30 SEC. 2.5°C ± 0.5°C/SEC. 3°C + 1°C/–0.5°C TIGHT TYPICAL LOOSE ROOM TEMPERATURE PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 217 °C RAMP-DOWN 6 °C/SEC. MAX. RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C 260 +0/-5 °C t 25 °C to PEAK 60 to 150 SEC. 20-40 SEC. TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE tp ts PREHEAT 60 to 180 SEC. tL TL Tsmax Tsmin Tp TIME TEMPERATURE NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C Note: Non-halide flux should be used. Note: Non-halide flux should be used. IEC/EN/DIN EN 60747-5-2 Approved under : IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884Teil 2):2003-01

Insulation and Safety Related Specifications 8-Pin DIP (300 Mil) SO-8 Parameter Symbol Value Value Units Conditions Minimum External Air L (101) 7.1 4.9 mm Measured from input terminals to output Gap (External Clearance) terminals, shortest distance through air. Minimum External Tracking L (102) 7.4 4.8 mm Measured from input terminals to output (External Creepage) terminals, shortest distance path along body. Minimum Internal Plastic 0.08 0.08 mm Through insulation distance, conductor to Gap (Internal Clearance) conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Tracking Resistance CTI 200 200 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-2Insulation Related Characteristics Description Symbol PDIP Option 060 SO-8 Option 60 Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 V rms I-IV for rated mains voltage ≤ 300 V rms I-IV I-III for rated mains voltage ≤ 600 V rms I-III I-II Climatic Classification 55/85/21 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 2 Maximum Working Insulation Voltage VIORM 630 566 Vpeak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test VPR 1181 1063 Vpeak with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.5 = VPR, Type and Sample Test, VPR 945 849 Vpeak t m = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* VIOTM 6000 4000 Vpeak (Transient Overvoltage, t ini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature TS 175 150 ˚C Input Current IS,INPUT 230 150 mA Output Power PS,OUTPUT 600 600 mW Insulation Resistance at T S, VIO = 500 V RS ≥ 109 ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica - tion.

Parameter Symbol Min. Max. Units Note Storage Temperature TS –55 125 °C Operating Temperature TA –55 100 °C Average Forward Input Current IF(AVG) 25 mA 1 Peak Forward Input Current IF(PEAK) 50 mA 2 (50% duty cycle, 1 ms pulse width) Peak Transient Input Current IF(TRANS) 1 A (≤ 1 µs pulse width, 300 pps) Reverse LED Input Voltage (Pin 3-2) VR 5 V Input Power Dissipation PIN 45 mW 3 Average Output Current (Pin 6) IO(AVG) 8 mA Peak Output Current IO(PEAK) 16 mA Emitter-Base Reverse Voltage VEBR 5 V Supply Voltage (Pin 8-5) VCC –0.5 7 V Output Voltage (Pin 6-5) VO –0.5 7 V Base Current IB 5 mA Output Power Dissipation PO 100 mW 4 Lead Solder Temperature (Through Hole Parts Only) 1.6 mm below seating plane, 10 sec. TLS 260 °C up to seating plane, 10 seconds 260 °C Reflow Temperature Profile TRP See Package Outline Drawings section Recommended Operating Conditions Parameter Symbol Min. Max. Units Power Supply Voltage VCC 2.7 7.0 V Forward Input Current IF(ON) 16 20 mA Forward Input Voltage VF(OFF) 0 0.8 V Operating Temperature TA 0 85 °C

Electrical Specifications (DC) Over Recommended Temperature (TA = 0˚C to +70˚C), VCC = 3.3 V, IF = 16 mA, unless otherwise specified. See Note 13. Current Transfer CTR 15 20 50 % TA = 25˚C VO = 0.4 V IF = 16 mA, 2 5, 11 VCC = 3.3 V Logic Low VOL 0.05 0.3 V TA = 25˚C IO = 3.0 mA IF = 16 mA, VCC = 3.3 V Logic High IOH 0.003 1 µA TA = 25˚C VO = VCC = 3.3 V IF = 0 mA 4 Output Current Logic Low ICCL HCPL-050L 43.0 100 µA IF = 16 mA, VO = Open, VCC = 3.3 V 13 Supply Current HCPL-250L HCPL-053L 90 300 HCPL-253L Logic High ICCH HCPL-050L 0.005 0.3 µA TA = 25˚C IF = 0 mA, VO = Open, 13 Supply Current HCPL-250L VCC = 3.3 V HCPL-053L 0.01 10 HCPL-253L Input Forward VF 1.52 1.7 V TA = 25˚C IF = 16 mA 1 Voltage Input Reverse BVR 5 V IR = 10 µA Breakdown Voltage Input CIN 60 pF f = 1 MHz, VF = 0 V Capacitance Ratio Output Voltage Electrical Specifications (DC) Over Recommended DC Temperature (TA = 0°C to +70°C, VCC = 5V, IF = 16mA) unless otherwise specified.(See note 13.) Current Transfer Ratio CTR HCPL-050L HCPL-250L 19 24 50 % VO=0.4V TA=25ºC, VCC=4.5V, IF = 16 mA 3 5,11 HCPL-053L HCPL-253L 19 24 50 % VO=0.5V Logic Low Output Voltage VOL HCPL-050L HCPL-250L 0.1 0.4 V IO = 3.0 mA TA=25ºC, IF = 16 mA, VCC=4.5VHCPL-053L HCPL-253L 0.1 0.5 V Logic High Output Current IOH 0 0.5 μA VO = VCC = 5.5V IF = 0 mA, TA=25ºC Logic Low Supply Current ICCL HCPL-050L HCPL-250L 50 200 μA VCC = 7V IF = 16 mA V0 = Open HCPL-053L HCPL-253L 100 400 Logic High Supply Current ICCH HCPL-050L HCPL-250L 0.02 1 μA TA=25ºC IF = 0 mA V0 = Open VCC = 7V HCPL-053L HCPL-253L 0.05 4 Input Forward Voltage VF 1.5 1.7 V TA = 25°C IF = 16 mA 1 1.8 Input Reverse Breakdown Voltage BVR 5 V IR = 10 μA Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 *All typical values at TA = 25°C

Switching Specifications (AC) Over Recommended Temperature (T A = 0˚C to +70˚C), V CC = 3.3 V, IF = 16 mA unless otherwise specified. All typicals at VCC = 3.3 V, TA = 25°C. Propagation tPHL 0.35 1 µs RL = 1.9 kΩ 7 8, 9 Delay Time to Logic Low at Output Propagation tPLH 0.65 1 µs RL = 1.9 kΩ 7 8, 9 Delay Time to Logic High at Output Common Mode |CMH| 1 kV/µs RL = 4.1 kΩ IF = 0 mA, TA = 25˚C, 8 7, 8, 9 Transient RL = 1.9 kΩ VCM = 10 Vp-p Immunity at CL = 15 pF Logic High Level Output Common Mode |CML| 1 kV/µs RL = 4.1 kΩ IF = 16 mA, TA = 25˚C, 8 7, 8, 9 Transient RL = 1.9 kΩ VCM = 10 Vp-p Immunity at CL = 15 pF Logic Low Level Output *All typicals at TA = 25˚C Switching Specifications (AC) Over Recommended Temperature (TA = 0°C to +70°C, VCC = 5 V, IF = 16mA, unless otherwise specified. Propagation Delay Time to LogicLow at Output tPHL 0.2 0.8 μs TA = 25°C, RL= 1.9KΩ 7 8,9 Propagation De- lay Time to Logic High at Output tPLH 0.6 0.8 μs TA = 25°C, RL = 1.9 kΩ 7 8,9 Common Mode Transient Im- munity at Logic High Output |CMH| 1 kV/μs RL = 1.9 kΩ IF = 0 mA, TA = 25°C, |VCM| = 10 Vp-p, CL = 15 pF 8 7,8,9 Common Mode Transient Immu- nity at Logic Low Output |CML| 1 kV/μs RL = 1.9 kΩ IF = 16 mA, TA = 25°C, |VCM| = 10 Vp-p 8 7,8,9 *All typical values at TA = 25°C

Over Recommended Temperature (TA = 0˚C to 70˚C) unless otherwise specified. Input-Output VISO 8-Pin DIP 3750 V rms RH < 50%, 6, 14 Momentary SO-8 t = 1 min., Withstand TA = 25˚C Voltage** I I-O 8-Pin DIP 1 µA 45% RH, t = 5 s, 6, 16 VI-O = 3 kVdc, TA = 25˚C Input-Output RI-O 8-Pin DIP 1012 Ω VI-O = 500 Vdc 6 Resistance SO-8 Input-Output CI-O 8-Pin DIP 0.6 pF f = 1 MHz 6 Capacitance SO-8 *All typicals at TA = 25˚C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage, " publica- tion number 5963-2203E. Notes: 1. Derate linearly above 70˚C free-air temperature at a rate of 0.8 mA/˚C (8-Pin DIP). Derate linearly above 85˚C free-air temperature at a rate of 0.5 mA/˚C (SO-8). 2. Derate linearly above 70˚C free-air temperature at a rate of 1.6 mA/˚C (8-Pin DIP). Derate linearly above 85˚C free-air temperature at a rate of 1.0 mA/˚C (SO-8). 3. Derate linearly above 70˚C free-air temperature at a rate of 0.9 mW/˚C (8-Pin DIP). Derate linearly above 85˚C free-air temperature at a rate of 1.1 mW/˚C (SO-8). 4. Derate linearly above 70˚C free-air temperature at a rate of 2.0 mW/˚C (8-Pin DIP). Derate linearly above 85˚C free-air temperature at a rate of 2.3 mW/˚C (SO-8). 5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100. 6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. 7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the com- mon mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient im- munity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 10. The frequency at which the AC output voltage is 3 dB below its mid-frequency value. 11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 15%. 12. See Option 020 data sheet for more information. 13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended. 14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insula- tion Related Characteristics Table, if applicable. 15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insula- tion Related Characteristics Table, if applicable. 16. This rating is equally validated by an equivalent AC proof test.

Figure 4. Logic high output current vs. tempera-

8 PIN DIP, SO-8

Figure 6. Thermal derating curve, dependence of Figure 3. Current transfer ratio vs. temperature Figure 5. Logic high output current vs. temperature

8 PIN DIP , SO-8

8 PIN DIP , SO-88 PIN DIP , SO-8

Figure 8. Test circuit for transient immunity and typical waveforms. Figure 7. Switching test circuit.

0 V 10% 90% 90% 10%

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.