HCPL-0500-500E

HCPL-0500-500E AVAGO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 17

Technical content

Features

• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP , SO-8, widebody packages
• Open collector output
• Safety approval UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-2 Approved – VIORM = 560 V peak for SO8 devices – VIORM = 630 V peak for DIP 300mil devices – VIORM = 1414 V peak for DIP 400mil (widebody) devices
• Dual channel version available (253X/053X/0534)

Applications

• High voltage insulation
• Video signal isolation
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL
• Replaces pulse transformers
• Replaces slow phototransistor isolators
• Analog signal ground isolation Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product 4 5 8NC ANODE CATHODE NC VCC VB VO GND TRUTH TABLE (POSITIVE LOGIC) LED ON OFF VO LOW HIGH CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

Minimum CMR 8-Pin DIP Small-Outline Widebody (300 Mil) SO-8 (400 Mil) Current Single Dual Single Dual Single dV/dt VCM Transfer Channel Channel Channel Channel Channel (V/µs) (V) Ratio (%) Package Package* Package Package* Package 1,000 10 7 6N135 HCPL-2530 HCPL-0500 HCPL-0530 HCNW135 19 6N136 HCPL-2531 HCPL-0501 HCPL-0531 HCNW136

15 HCPL-2502

*Technical data for these products are on separate Avago publications. IF SHIELD GND VCC VO ICC VF IO ANODE CATHODE VB IB

Ordering Information

6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW135, HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices above listed are approved under CSA Component Acceptance Notice #5, File CA 88324. Part number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute rating IEC/EN/DIN EN 60747- 5-2 Quantity RoHS Compliant Non RoHS Compliant 6N135 6N136 HCPL-2502 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube -520E #520 X X X X 1000 per reel -060E #060 X 50 per tube -360E #360 X X X 50 per tube -560E #560 X X X X 1000 per reel HCPL-0500 HCPL-0501 -000E No option SO-8 100 per tube -500E #500 X X X 1500 per reel -060E #060 X 100 per tube -560E #560 X X X X 1500 per reel HCNW135 HCNW136 -000E No option 400mil Widebody DIP-8 X X 42 per tube -300E #300 X X X X 42 per tube -500E #500 X X X X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2502-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-2502 to order product of 300mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘ .

1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) A XXXXZ YYWW DATE CODE DIMENSIONS IN MILLIMETERS AND (INCHES). 5678 4321 OPTION CODE* UL RECOGNITION UR TYPE NUMBER *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005) Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-2502) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6) 0.635 ± 0.25 (0.025 ± 0.010) 12° NOM. 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 1.080 ± 0.320 (0.043 ± 0.013) 3.56 ± 0.13 (0.140 ± 0.005) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002)

Small Outline SO-8 Package (HCPL-0500/1) 8-Pin Widebody DIP Package (HCNW135/6) XXX YWW 8 7 6 5 4321 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.050)BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012)MIN. TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 0.203 ± 0.102 (0.008 ± 0.004) PIN ONE 0 ~ 7° 7.49 (0.295) 1.9 (0.075) 0.64 (0.025) LAND PATTERN RECOMMENDATION 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 1.8 ± 0.15 (0.071 ± 0.006) 5.10 (0.201)MAX. 1.55 (0.061) MAX. 2.54 (0.100) TYP. DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 7 TYP. 0.254 + 0.076 - 0.0051 (0.010+ 0.003) - 0.002) 11.00 (0.433) 9.00 ± 0.15 (0.354 ± 0.006) MAX. 10.16 (0.400) TYP. A HCNWXXXX YYWW DATE CODE TYPE NUMBER 0.51 (0.021) MIN. 0.40 (0.016) 0.56 (0.022) 3.10 (0.122) 3.90 (0.154)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6) Solder Reflow Temperature Profile TIME (SECONDS) TEMPERATURE (°C) 200 100 50 150100 200 250 300 SEC. 50 SEC. SEC. 160 °C 140 °C 150 °C PEAK TEMP. 245 °C PEAK TEMP. 240 °C PEAK TEMP. 230 °C SOLDERING TIME 200 °C PREHEATING TIME 150 °C, 90 + 30 SEC. 2.5 C ± 0.5 °C/SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE PREHEATING RATE 3 °C + 1 °C/–0.5 °C/SEC. REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC. NOTE: NON-HALIDE FLUX SHOULD BE USED. 1.00 ± 0.15 (0.039 ± 0.006) 7 NOM. 12.30 ± 0.30 (0.484 ± 0.012) 0.75 ± 0.25 (0.030 ± 0.010) 11.00 (0.433) 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 9.00 ± 0.15 (0.354 ± 0.006) 1.3 (0.051) 13.56 (0.534) 2.29 (0.09) LAND PATTERN RECOMMENDATION 1.80 ± 0.15 (0.071 ± 0.006) 4.00 (0.158)MAX. 1.55 (0.061) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.0051 (0.010+ 0.003) - 0.002) MAX.

The devices contained in this data sheet have been approved by the following organizations: UL Recognized under UL 1577 , Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (HCNW and Option 060 only) Recommended Pb-Free IR Profile Insulation and Safety Related Specifications 8-Pin DIP Widebody (300 Mil) SO-8 (400 Mil) Parameter Symbol Value Value Value Units Conditions Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals Air Gap (External to output terminals, shortest Clearance) distance through air. Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals Tracking (External to output terminals, shortest Creepage) distance path along body. Minimum Internal 0.08 0.08 1.0 mm Through insulation distance, Plastic Gap conductor to conductor, usually (Internal Clearance) the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal NA NA 4.0 mm Measured from input terminals Tracking (Internal to output terminals, along Creepage) internal cavity. Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 217 °C RAMP-DOWN 6 °C/SEC. MAX. RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C * 260 +0/-5 °C t 25 °C to PEAK 60 to 150 SEC. 15 SEC. TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATUREtp ts PREHEAT 60 to 180 SEC. tL TL Tsmax Tsmin Tp TIME TEMPERATURE NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C NON-HALIDE FLUX SHOULD BE USED. * RECOMMENDED PEAK TEMPERATURE FOR WIDEBODY 400mils PACKAGE IS 245 °C

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (OPTION 060 ONLY) Characteristic Description Symbol 8 Pin DIP SO-8 Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms I-IV I-III for rated mains voltage ≤450 V rms I-III Climatic Classification 55/100/21 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 2 Maximum Working Insulation Voltage VIORM 630 560 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 1050 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.5 = VPR, Type and sample test, VPR 945 840 V peak t m = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 6000 4000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature TS 175 175 °C Input Current IS,INPUT 230 150 mA Output Power PS,OUTPUT 600 600 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW135/6 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤600 V rms I-IV for rated mains voltage ≤1000 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 1414 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak t m = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature TS 150 °C Input Current IS,INPUT 400 mA Output Power PS,OUTPUT 700 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

Parameter Symbol Device Min. Max. Units Note Storage Temperature* TS -55 125 °C Operating Temperature* TA 8-Pin DIP -55 100 °C SO-8 Widebody -55 85 Average Forward Input Current* IF(AVG) 25 mA 1 Peak Forward Input Current* IF(PEAK) 8-Pin DIP 2 (50% duty cycle, 1 ms pulse width) SO-8 50 mA (50% duty cycle, 1 ms pulse width) Widebody 40 Peak Transient Input Current* IF(TRANS) 8-Pin DIP 1 A (≤1 µs pulse width, 300 pps) SO-8 Widebody 0.1 Reverse LED Input Voltage* (Pin 3-2) VR 8-Pin DIP 5 V SO-8 Widebody 3 Input Power Dissipation* PIN 8-Pin DIP 45 mW 3 SO-8 Widebody 40 Average Output Current* (Pin 6) IO(AVG) 8 mA Peak Output Current* IO(PEAK) 16 mA Emitter-Base Reverse Voltage* (Pin 5-7) VEBR 5 V Supply Voltage (Pin 8-5) VCC -0.5 30 V Output Voltage (Pin 6-5) VO -0.5 20 V Supply Voltage* (Pin 8-5) VCC -0.5 15 V Output Voltage* (Pin 6-5) VO -0.5 15 V Base Current* (Pin 7) IB 5 mA Output Power Dissipation* PO 100 mW 4 Lead Solder Temperature* (Through-Hole Parts Only) 1.6 mm below seating plane, 10 seconds TLS 8-Pin DIP 260 °C up to seating plane, 10 seconds Widebody 260 °C Reflow Temperature Profile TRP SO-8 and Option 300 *Data has been registered with JEDEC for the 6N135/6N136. See Package Outline Drawings section

Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Symbol Device Min. Typ.** Max. Units Test Conditions Fig. Note Current Transfer Ratio CTR* 6N135 HCPL-0500 HCNW135 7 18 50 % TA = 25°C VO = 0.4 V IF = 16 mA, VCC = 4.5 V 1, 2, 5, 11 5 19 VO = 0.5 V HCPL-2502 15 22 TA = 25°C VO = 0.4 V 15 25 VO = 0.5 V 6N136 HCPL-0501 HCNW136 19 24 50 TA = 25°C VO = 0.4 V 15 25 VO = 0.5 V Logic Low Output Voltage VOL 6N135 HCPL-0500 HCNW135 0.1 0.4 V TA = 25°C IO = 1.1 mA IF = 16 mA, VCC = 4.5 V0.1 0.5 IO = 0.8 mA 6N136 HCPL-2502 HCPL-0501 HCNW136 0.1 0.4 TA = 25°C IO = 3.0 mA 0.1 0.5 IO = 2.4 mA Logic High Output Current IOH* 0.003 0.5 µA TA = 25°C VO = VCC = 5.5 V IF = 0 mA 7 0.01 1 TA = 25°C VO = VCC = 15 V

50 VO = VCC = 15 V

ICCL 50 200 µA IF = 16 mA, VO = Open, VCC = 15 V Logic High Supply Current ICCH* 0.02 1 µA TA = 25°C IF = 0 mA, VO = Open,

2 VCC = 15 V

Input Forward VF* Voltage 8-Pin DIP 1.5 1.7 V TA = 25°C IF = 16 mA 3 SO-8 1.8 Widebody 1.45 1.68 1.85 TA = 25°C IF = 16 mA 1.35 1.95 Input Reverse Breakdown Voltage BVR* 8-Pin DIP 5 V IR = 10 µA SO-8 Widebody 3 IR = 100 µA Temperature Coefficient of Forward Volt- age ∆VF/ ∆TA 8-Pin DIP -1.6 mV/°C IF = 16 mA SO-8 Widebody -1.9 Input Capacitance CIN 8-Pin DIP 60 pF f = 1 MHz, VF = 0 V SO-8 Widebody 90 Transistor DC Current Gain hFE 8-Pin DIP 150 VO = 5 V, IO = 3 mA SO-8 130 VO = 0.4 V, IB = 20 µA Widebody 180 VO = 0.4 V, IB = 20 µA

160 VO = 5 V, IO = 3 mA

*For JEDEC registered parts. **All typicals at TA = 25°C.

Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Propagation tPHL* 6N135 0.2 1.5 µs TA = 25°C RL = 4.1 kΩ 5, 6, 8, 9 HCPL-0500 2.0 11 HCNW135 6N136 0.2 0.8 TA = 25°C RL = 1.9 kΩ HCPL-2502 HCPL-0501 HCNW136 1.0 Propagation tPLH* 6N135 1.3 1.5 µs TA = 25°C RL = 4.1 kΩ 5, 6, 8, 9 HCPL-0500 2.0 11 HCNW135 6N136 0.6 0.8 TA = 25°C RL = 1.9 kΩ HCPL-2502 HCPL-0501 HCNW136 1.0 Common Mode |CMH| 6N135 1 kV/µs RL = 4.1 kΩ I F = 0 mA, TA = 25°C, 12 7, 8, HCPL-0500 1 VCM = 10 Vp-p 9 HCNW135 CL = 15 pF 6N136 1 RL = 1.9 kΩ HCPL-2502 1 HCPL-0501 Common Mode |CML| 6N135 1 kV/µs RL = 4.1 kΩ I F = 16 mA, TA = 25°C, 12 7, 8, HCPL-0500 1 VCM = 10 Vp-p 9 HCNW135 CL = 15 pF 6N136 1 RL = 1.9 kΩ HCPL-2502 1 HCPL-0501 Bandwidth BW 6N135/6 9 MHz See Test Circuit 8, 10 10 HCPL-2502 HCPL-0500/1 HCNW135/6 11 *For JEDEC registered parts. **All typicals at TA = 25°C. Delay Time to Logic Low at Output Delay Time to Logic High at Output Transient Im- munity at Logic High Level Output Transient Im- munity at Logic Low Level Output

Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8). 2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8). 3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8). 4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8). 5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100. 6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. 7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value. 11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%. 12. See Option 020 data sheet for more information. 13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended. 14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable. 15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable. 16. This rating is equally validated by an equivalent ac proof test. Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Input-Output VISO 8-Pin DIP 3750 V rms RH < 50%, 6, 14 Momentary SO-8 t = 1 min., Withstand TA = 25°C Voltage** 8-Pin DIP 5000 6, 12, (Option 020) 15 II-O 8-Pin DIP 1 µA 45% RH, t = 5 s, 6, 16 VI-O = 3 kVdc, TA = 25°C Input-Output RI-O 8-Pin DIP 1012 Ω VI-O = 500 Vdc 6 Resistance SO-8 Widebody 1012 1013 T A = 25°C

1011 TA = 100°C

Input-Output CI-O 8-Pin DIP 0.6 pF f = 1 MHz 6 Capacitance SO-8 Widebody 0.5 0.6 *All typicals at TA = 25°C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage, ” publication number 5963-2203E. Widebody 5000 6, 15

8 PIN DIP, SO-8

Figure 2. Current transfer ratio vs. input current. Figure 3. Input current vs. forward voltage. Figure 1. DC and pulsed transfer characteristics.

Figure 6. Propagation delay time vs. load resistance. Figure 5. Propagation delay vs. temperature. Figure 4. Current transfer ratio vs. temperature.

Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2. Figure 8. Small-signal current transfer ratio vs. quiescent input current. Figure 7. Logic high output current vs. temperature.

Figure 10. Frequency response.