HCPL-0453

HCNW4502 AVAGO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Features

• 15 kV/µs minimum common mode transient immunity at VCM = 1500 V
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP , SO-8, widebody packages
• Open collector output
• Guaranteed performance from temperature: 0°C to 70°C
• Safety approval UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-5 Approved – VIORM = 630 V peak for HCPL-4503#060 – VIORM = 1414 V peak for HCNW devices
• Dual channel version available (4534/0534)
• MIL-PRF-38534 hermetic version available (55XX/65XX/4N55)

Applications

• High voltage insulation
• Video signal isolation
• Power transistor isolation in motor drives
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL
• Replaces pulse transformers
• Replaces slow phototransistor isolators
• Analog signal ground isolation Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. 4 5 8NC ANODE CATHODE NC VCC NC Vo GND TRUTH TABLE (POSITIVE LOGIC) LED ON OFF Vo LOW HIGH

Minimum CMR 8-Pin DIP (300 Mil) Small-Outline SO-8 (400 Mil) Hermetic Current Single Dual Single Dual Single Single and dV/dt VCM Transfer Channel Channel Channel Channel Channel Dual Channel (V/µs) (V) Ratio (%) Package Package* Package Package* Package Packages* 10 19 HCPL-4502 HCPL-0452 HCNW4502 15,000 1500 19 HCPL-4503 HCPL-4534 HCPL-0453 HCPL-0534 HCNW4503 1,000 10 9 HCPL-55XX HCPL-65XX 4N55 *Technical data for these products are on separate Avago publications. The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL- 0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µs minimum at VCM = 1500 V guaranteed. IF SHIELD HCPL-4503/0453 HCNW4503

5 GND

Ordering Information

HCPL-4502 and HCPL-4503, HCPL-0452, HCPL-0453 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW4502 and HCNW4503 are UL Recognized with 5000 V rms for 1 minute per UL1577. All devices isted above are ap - proved under CSA Component Acceptance Notice #5, File CA 88324. Part number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/

1 Minute rating

-000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube -520E #520 X X X X 1000 per reel -060E #060 X 50 per tube -360E #360 X X X 50 per tube -560E #560 X X X X 1000 per reel HCPL-0452 HCPL-0453 -000E No option SO-8 100 per tube -500E #500 X X X 1500 per reel -060E #060 X 100 per tube -560E #560 X X X X 1500 per reel HCNW4502 HCNW4503 -000E No option 400mil Widebody DIP-8 X X 42 per tube -300E #300 X X X X 42 per tube -500E #500 X X X X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-4502-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-4502 to order product of 300mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘ .

1.080 ± 0.320 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) A XXXXZ YYWW DATE CODE Dimensions in millimeters and (inches). 5678 4321 OPTION CODE* UL RECOGNITION UR TYPE NUMBER *marking code letter for option numbers "L" = option 020 "V" = option 060 Option numbers 300 and 500 not marked. Note: Floating lead protrusion is 0.25 mm (10 mils) max. 3.56 ± 0.13 (0.140 ± 0.005) Package Outline Drawings 8-Pin DIP Package (HCPL-4502/3) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4502/3) 0.635 ± 0.25 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 1.080 ± 0.320 (0.043 ± 0.013) 3.56 ± 0.13 (0.140 ± 0.005) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC Dimensions in millimeters (inches). Lead coplanarity = 0.10 mm (0.004 inches). Note: Floating lead protrusion is 0.25 mm (10 mils) max. 0.254 + 0.076 - 0.051 (0.010 + 0.003) - 0.002)

Small Outline SO-8 Package (HCPL-0452/3) 8-Pin Widebody DIP Package (HCNW4502/3) XXX YWW 4321 5678 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.050) BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012)MIN. Total package length (inclusive of mold flash) Dimensions in millimeters (inches). Lead coplanarity = 0.10 mm (0.004 inches) max. 0.203 ± 0.102 (0.008 ± 0.004) 7 ° PIN ONE 0 ~ 7 ° 7.49 (0.295) 1.9 (0.075) 0.64 (0.025) LAND PATTERN RECOMMENDATION 5678 4321 11.15 ± 0.15 (0.442 ± 0.006) 1.78 ± 0.15 (0.070 ± 0.006) 5.10 (0.201) MAX. 1.55 (0.061) MAX. 2.54 (0.100) TYP. Dimensions in millimeters (inches). Note: Floating lead protrusion is 0.25 mm (10 mils) max. 7° TYP. 0.254 + 0.076 - 0.0051 (0.010+ 0.003) - 0.002) 11.00 (0.433) 9.00 ± 0.15 (0.354 ± 0.006) MAX. 10.16 (0.400) TYP. A HCNWXXXX YYWW DATE CODE TYPE NUMBER 0.51 (0.021) MIN. 0.40 (0.016) 0.56 (0.022) 3.10 (0.122) 3.90 (0.154)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4502/3) Solder Reflow Temperature Profile 1.00 ± 0.15 (0.039 ± 0.006) 7° NOM. 12.30 ± 0.30 (0.484 ± 0.012) 0.75 ± 0.25 (0.030 ± 0.010) 11.00 (0.433) 5678 4321 11.15 ± 0.15 (0.442 ± 0.006) 9.00 ± 0.15 (0.354 ± 0.006) 1.3 (0.051) 13.56 (0.534) 2.29 (0.09) LAND PATTERN RECOMMENDATION 1.78 ± 0.15 (0.070 ± 0.006) 4.00 (0.158) MAX. 1.55 (0.061) MAX. 2.54 (0.100) BSC Dimensions in millimeters (inches). Lead coplanarity = 0.10 mm (0.004 inches). Note: Floating lead protrusion is 0.25 mm (10 mils) max. 0.254 + 0.076 - 0.0051 (0.010 + 0.003) - 0.002) MAX. TIME (SECONDS) TEMPERATURE (°C) 200 100 50 150100 200 250 300 SEC. 50 SEC. SEC. 160°C 140°C 150°C PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C SOLDERING TIME 200°C PREHEATING TIME 150°C, 90 + 30 SEC. 2.5 C ± 0.5°C/SEC. 3°C + 1°C/–0.5°C TIGHT TYPICAL LOOSE ROOM TEMPERATURE Note: Non-halide flux should be used. PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.

The devices contained in this data sheet have been approved by the following organizations: UL Recognized under UL 1577 , Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-5 (HCNW and option 060 only) Approved with Maximum Working Insulation Voltage Viorm=560Vpeak for HCPL-0452/0453, Viorm=630 Vpeak for HCPL-4502/4503, and Viorm=1414 Vpeak for HCNW4502/4503. Recommended Pb-Free IR Profile Insulation and Safety Related Specifications 8-Pin DIP Widebody (300 Mil) SO-8 (400 Mil) Parameter Symbol Value Value Value Unit Conditions Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals Air Gap (External to output terminals, shortest Clearance) distance through air. Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals Tracking (External to output terminals, shortest Creepage) distance path along body. Minimum Internal 0.08 0.08 1.0 mm Through insulation distance, Plastic Gap conductor to conductor, usually (Internal Clearance) the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal NA NA 4.0 mm Measured from input terminals Tracking (Internal to output terminals, along Creepage) internal cavity. Tracking Resistance CTI > 175 > 175 > 175 V DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 217°C RAMP-DOWN 6°C/SEC. MAX. RAMP-UP 3°C/SEC. MAX.150 - 200°C * 260 +0/-5°C t 25°C to PEAK 60 to 150 SEC. 15 SEC. TIME WITHIN 5°C of ACTUAL PEAK TEMPERATUREtp ts PREHEAT 60 to 180 SEC. tL TL Tsmax Tsmin Tp TIME TEMPERATURE Notes: The time from 25°C to peak Temperature = 8 minutes max. T smax = 200°C, tsmin = 150°C Non-halide flux should be used. * Recommended peak temperature for Widebody 400mils package is 245°C

IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics (HCNW4502/3 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤600 V rms I-IV for rated mains voltage ≤1000 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage VIORM 1414 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.6 = VPR, Type and sample test, VPR 2262 V peak t m = 10 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 60 sec) VIOTM 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature TS 150 °C Input Current IS,INPUT 400 mA Output Power PS,OUTPUT 700 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics ( OPTION 060 ONLY) Characteristic Description Symbol HCPL-4502/4503 HCPL-0452/0453 Units Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 300 Vrms I-IV I-IV for rated mains voltage ≤ 600 Vrms I-IV I-I I I Climatic Classification 55/100/21 55/100/21 Pollution Degree (DIN VDE 0110/39) 2 2 Maximum Working Insulation Voltage VIORM 630 560 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 1050 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.6 = VPR, Type and sample test, VPR 1008 896 V peak t m = 10 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 60 sec) VIOTM 8000 6000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature TS 175 175 °C Input Current IS,INPUT 230 150 mA Output Power PS,OUTPUT 600 600 mW Insulation Resistance at TS, VIO = 500 V RS ≥10 9 ≥10 9 Ω

Parameter Symbol Device Min. Max. Units Note Storage Temperature TS -55 125 °C Operating Temperature TA 8-Pin DIP -55 100 °C SO-8 Widebody -55 85 Average Forward Input Current IF(AVG) 25 mA 1 Peak Forward Input Current IF(PEAK) 8-Pin DIP 2 (50% duty cycle, 1 ms pulse width) SO-8 50 mA (50% duty cycle, 1 ms pulse width) Widebody 40 Peak Transient Input Current IF(TRANS) 8-Pin DIP 1 A (≤1 µs pulse width, 300 pps) SO-8 Widebody 0.1 Reverse LED Input Voltage (Pin 3-2) VR 8-Pin DIP 5 V SO-8 Widebody 3 Input Power Dissipation PIN 8-Pin DIP 45 mW 3 SO-8 Widebody 40 Average Output Current (Pin 6) IO(AVG) 8 mA Peak Output Current IO(PEAK) 16 mA Emitter-Base Reverse Voltage VEBR 5 V (Pin 5-7, except 4502/3, 0452/3) Supply Voltage (Pin 8-5) VCC -0.5 30 V Output Voltage (Pin 6-5) VO -0.5 20 V Base Current (Pin 7, except 4502/3, 0452/3) IB 5 mA Output Power Dissipation PO 100 mW 4 Lead Solder Temperature (Through-Hole Parts Only) 1.6 mm below seating plane, 10 seconds TLS 8-Pin DIP 260 °C up to seating plane, 10 seconds Widebody 260 °C Reflow Temperature Profile TRP SO-8 and Option 300 See Package Outline Drawings section

Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Symbol Device Min. Typ.* Max. Units Test Conditions Fig. Note Current Transfer Ratio CTR HCPL-4502/3 HCPL-0452/3 HCNW4502/3 50 TA = 25°C VO = 0.4 V VO = 0.5 V IF = 16 mA, VCC = 4.5 V 1, 2, Logic Low Output Voltage VOL HCPL-4502/3 HCPL-0452/3 HCNW4502/3 0.1 0.1 0.4 0.5 TA = 25°C IO = 3.0 mA IO = 2.4 mA IF = 16 mA, VCC = 4.5 V Logic High Output Current IOH 0.003 0.5 µA TA = 25°C VO = VCC = 5.5 V IF = 0 mA 7 0.01 1 TA = 25°C VO = VCC = 15 V

50 VO = VCC = 15 V

ICCL 50 200 µA IF = 16 mA, VO = Open, VCC = 15 V Logic High Supply Current ICCH 0.02 1 µA TA = 25°C IF = 16 mA, VO = Open,

2 VCC = 15 V

1.5 1.7 V TA = 25°C IF = 16 mA 3 1.8 Widebody 1.45 1.68 1.85 TA = 25°C IF = 16 mA 1.35 1.95 Input Reverse Breakdown Voltage BVR 8-Pin DIP SO-8

5 V IR = 10 µA

Widebody 3 IR = 100 µA Temperature Coefficient of Forward Volt- age ∆VF/ ∆TA 8-Pin DIP SO-8 -1.6 mV/°C IF = 16 mA Widebody -1.9 Input Capacitance CIN 8-Pin DIP SO-8 60 pF f = 1 MHz, VF = 0 V Widebody 90 Transistor DC Current Gain hFE 8-Pin DIP SO-8

150 VO = 5 V, IO = 3 mA

130 VO = 0.4 V, IB = 20 µA Widebody 180 VO = 0.4 V, IB = 20 µA

160 VO = 5 V, IO = 3 mA

*All typicals at TA = 25°C.

Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Propagation tPHL HCPL-4502/3 0.2 0.8 TA = 25°C RL = 1.9 kΩ 5, 6, 8 HCPL-0452/3 1.0 10 HCNW4502/3 Propagation tPLH HCPL-4502/3 0.6 0.8 TA = 25°C RL = 1.9 kΩ 5, 6, 8 HCPL-0452/3 1.0 10 HCNW4502/3 Common Mode |CMH| HCPL-4502 1 kV/µs RL = 1.9 kΩ IF = 0 mA, TA = 25°C, 11 7, 8 HCPL-0452 VCM = 10 Vp-p HCNW4502 CL = 15 pF HCPL-4503 15 30 RL = 1.9 kΩ IF = 0 mA, TA = 25°C, HCPL-0453 VCM = 1500 Vp-p, HCNW4503 CL = 15 pF Common Mode |CML| HCPL-4502 1 kV/µs RL = 1.9 kΩ IF = 16 mA, TA = 25°C, 11 7, 8 HCPL-0452 VCM = 10 Vp-p HCNW4502 CL = 15 pF HCPL-4503 15 30 RL = 1.9 kΩ IF = 16 mA, TA = 25°C, HCPL-0453 VCM = 1500 Vp-p, HCNW4503 CL = 15 pF *All typicals at TA = 25°C. Delay Time to Logic Low at Output Delay Time to Logic High at Output Transient Im- munity at Logic High Level Output Transient Im- munity at Logic Low Level Output

Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8). 2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8). 3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8). 4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8). 5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100. 6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. 7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 9. See Option 020 data sheet for more information. 10. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended. 11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. 12. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. 13. This rating is equally validated by an equivalent ac proof test. Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Input-Output VISO 8-Pin DIP 3750 V rms RH < 50%, 6, 11 Momentary SO-8 t = 1 min., Withstand Widebody 5000 TA = 25°C 6, 12 Voltage** 8-Pin DIP 5000 6, 9, (Option 020) 12 II-O 8-Pin DIP 1 µA 45% RH, t = 5 s, 6, 13 V I-O = 3 kVdc, T A = 25°C Input-Output RI-O 8-Pin DIP 1012 Ω VI-O = 500 Vdc 6 Resistance SO-8 Widebody 1012 10 13 TA = 25°C

1011 TA = 100°C

Input-Output CI-O 8-Pin DIP 0.6 pF f = 1 MHz 6 Capacitance SO-8 Widebody 0.5 0.6 *All typicals at TA = 25°C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage, ” publication num- ber 5963-2203E.

8 PIN DIP, SO-8

16 WIDEBODY

8 PIN DIP , SO-8

8 PIN DIP , SO-8 WIDEBODY

Figure 2. Current transfer ratio vs. input current. Figure 3. Input current vs. forward voltage. Figure 1. DC and pulsed transfer characteristics.

14 NORMALIZED CURRENT TRANSFER RATIO

Figure 6. Propagation delay time vs. load resistance. Figure 5. Propagation delay vs. temperature. Figure 4. Current transfer ratio vs. temperature.

Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-5. Figure 8. Small-signal current transfer ratio vs. quiescent input current. Figure 7. Logic high output current vs. temperature.

0 V 10% 90% 90% 10%

Figure 11. Test circuit for transient immunity and typical waveforms. Figure 10. Switching test circuit. Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved.