HCPL-0211

HCPL-2231 AVAGO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 18

Technical content

Features

• 10 kV/µs minimum Common Mode Rejection (CMR) at VCM = 1000 V (HCPL-2211/2212/0211/2232, HCNW2211)
• Wide operating VCC range: 4.5 to 20 Volts
• 300 ns propagation delay guaranteed over the full temperature range
• 5 Mbd typical signal rate
• Low input current (1.6 mA to 1.8 mA)
• Hysteresis
• Totem pole output (no pullup resistor required)
• Available in 8-Pin DIP , SOIC-8, widebody packages
• Guaranteed performance from -40°C to 85°C
• Safety approval – UL recognized -3750 V rms for 1 minute (5000 V rms for 1 minute for HCNW22XX) per UL1577 – CSAapproved – IEC/EN/DIN EN 60747-5-2 approved with VIORM =

630 V peak (HCPL-2211/2212 Option 060 only) and

VIORM = 1414 V peak (HCNW22XX only)

• MIL-PRF-38534 hermetic version available (HCPL-52XX/62XX)

Applications

• Isolation of high speed logic systems
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Ground loop elimination
• Pulse transformer replacement
• High speed line receiver
• Power control systems Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product

The electrical and switching characteristics of the HCPL- 22XX, HCPL-02XX and HCNW22XX are guaranteed from -40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF and wide VCC range allow compati bil ity with TTL, LSTTL, and CMOS logic and result in lower power consump tion compared to other high speed couplers. Logic signals are transmitted with a typical propagation delay of 150 ns. Small- Widebody Minimum CMR Input 8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic On- Single Dual Single Single Single and dV/dt Current Channel Channel Channel Channel Dual Channel (V/µs) VCM (V) (mA) Package Package Package Package Packages 1,000 50 1.6 HCPL-2200[1,2] HCPL-0201 HCNW2201 HCPL-2201 HCPL-2202

1.8 HCPL-2231

2,500 400 1.6 HCPL-2219[1,2] 5,000[3] 300[3] 1.6 HCPL-2211 HCPL-0211 HCNW2211 HCPL-2212

1.8 HCPL-2232

1,000 50 2.0 HCPL-52XX[2] HCPL-62XX[2] Notes: 1. HCPL-2200/2219 devices include output enable/disable function. 2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications. 3. Minimum CMR of 10 kV/µs with VCM = 1000 V can be achieved with input current, IF, of 5 mA. Selection Guide

Ordering Information

HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324. Part number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute rating IEC/EN/DIN EN 60747-5-2 Quantity RoHS Compliant Non RoHS Compliant HCPL-2201 HCPL-2202 HCPL-2211 HCPL-2212 -000E No option 300mil DIP-8 50 per tube -300E -300 X X 50 per tube -500E -500 X X X 1000 per reel -060E -060 X 50 per tube -360E -360 X X X 50 per tube -560E -560 X X X X 1000 per reel HCPL-2231 HCPL-2232 -000E No option 50 per tube -300E -300 X X 50 per tube -500E -500 X X X 1000 per reel HCPL-0201 HCPL-0211 -000E No option SO-8 X 100 per tube -500E -500 X X 1500 per reel -060E -060 X X 100 per tube -560E -560 X X X 1500 per reel HCNW2201 HCNW2211 -000E No option 400mil Widebody DIP-8 X X 42 per tube -300E -300 X X X X 42 per tube -500E -500 X X X X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2202-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-2202 to order product of 300mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘ .

8-Pin DIP Package (HCPL-2201/02/11/12/31/32) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32) 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) A XXXXZ YYWW DATE CODE DIMENSIONS IN MILLIMETERS AND (INCHES). 5678 4321 OPTION CODE* UL RECOGNITION UR TYPE NUMBER * MARKING CODE LETTER FOR OPTION NUMBERS "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 0.635 ± 0.25 (0.025 ± 0.010) 12° NOM. 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 1.080 ± 0.320 (0.043 ± 0.013) 3.56 ± 0.13 (0.140 ± 0.005) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002)

Small-Outline SO-8 Package (HCPL-0201/11) 8-Pin Widebody DIP Package (HCNW2201/11) XXX YWW 8765 4321 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.050) BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45o X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012) MIN. TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 0.203 ± 0.102 (0.008 ± 0.004) PIN ONE 0 ~ 7o 7.49 (0.295) 1.9 (0.075) 0.64 (0.025) LAND PATTERN RECOMMENDATION 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 1.80 ± 0.15 (0.071 ± 0.006) 5.10 (0.201) MAX. 1.55 (0.061) MAX. 2.54 (0.100) TYP. DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 7o TYP. 0.254 + 0.076 - 0.0051 (0.010 + 0.003) - 0.002) 11.00 (0.433) 9.00 ± 0.15 (0.354 ± 0.006) MAX. 10.16 (0.400) TYP. A HCNWXXXX YYWW DATE CODE TYPE NUMBER 0.51 (0.021) MIN. 0.40 (0.016) 0.56 (0.022) 3.10 (0.122) 3.90 (0.154)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11) Solder Reflow Temperature Profile 1.00 ± 0.15 (0.039 ± 0.006) 7o NOM. 12.30 ± 0.30 (0.484 ± 0.012) 0.75 ± 0.25 (0.030 ± 0.010) 11.00 (0.433) 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 9.00 ± 0.15 (0.354 ± 0.006) 1.3 (0.051) 13.56 (0.534) 2.29 (0.09) LAND PATTERN RECOMMENDATION 1.80 ± 0.15 (0.071 ± 0.006) 4.00 (0.158) MAX. 1.55 (0.061) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.0051 (0.010 + 0.003) - 0.002) MAX. TIME (SECONDS) TEMPERATURE (°C) 200 100 50 150100 200 250 300 SEC. 50 SEC. SEC. 160 °C 140 °C 150 °C PEAK TEMP. 245 °C PEAK TEMP. 240 °C PEAK TEMP. 230 °C SOLDERING TIME 200 °C PREHEATING TIME 150 °C, 90 + 30 SEC. 2.5 C ± 0.5 °C/SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE PREHEATING RATE 3 °C + 1 °C/–0.5 °C/SEC. REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC. NOTE: NON-HALIDE FLUX SHOULD BE USED.

The HCPL-22XX/02XX and HCNW22XX have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (Option 060 and HCNW only) Recommended Pb-Free IR Profile Insulation and Safety Related Specifications 8-pin DIP Package 8-Pin DIP Widebody (300 Mil) SO-8 (400 Mil) Parameter Symbol Value Value Value Units Conditions Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals Air Gap (External to output terminals, shortest Clearance) distance through air. Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals Tracking (External to output terminals, shortest Creepage) distance path along body. Minimum Internal 0.08 0.08 1.0 mm Through insulation distance, Plastic Gap conductor to conductor, usually (Internal Clearance) the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal NA NA 4.0 mm Measured from input terminals Tracking (Internal to output terminals, along Creepage) internal cavity. Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 217 °C RAMP-DOWN 6 °C/SEC. MAX. RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C * 260 +0/-5 °C t 25 °C to PEAK 60 to 150 SEC. 15 SEC. TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATUREtp ts PREHEAT 60 to 180 SEC. tL TL Tsmax Tsmin Tp TIME TEMPERATURE NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C NOTE: NON-HALIDE FLUX SHOULD BE USED. * RECOMMENDED PEAK TEMPERATURE FOR WIDEBODY 400mils PACKAGE IS 245 °C

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-2211/2212 Option 060 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms I-IV for rated mains voltage ≤450 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 630 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.5 = VPR, Type and sample test, VPR 945 V peak t m = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 6000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 12, Thermal Derating curve.) Case Temperature TS 175 °C Input Current IS,OUTPUT 230 mA Output Power PS,OUTPUT 600 mW Insulation Resistance at TS, VIO = 500 V RS ≥109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica - tion.

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤600 V rms I-IV for rated mains voltage ≤1000 V rms I-III Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 1414 V peak Input to Output Test Voltage, Method b* V IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* V IORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak t m = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 12, Thermal Derating curve.) Case Temperature TS 150 °C Current (Input Current IF, PS = 0) IS,INPUT 400 mA Output Power PS,OUTPUT 700 mW Insulation Resistance at TS, VIO = 500 V RS ≥109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica - tion.

Parameter Symbol Min. Max. Units Note Storage Temperature TS -55 125 °C Operating Temperature TA -40 85 °C Average Forward Input Current IF(AVG) 10 mA 1 Peak Transient Input Current (≤ 1 µs Pulse Width, 300 pps) IF(TRAN) 1.0 A 1 (≤ 200 µs Pulse Width, HCNW22XX 40 mA < 1% Duty Cycle) Reverse Input Voltage VR 5 V 1 HCNW22XX 3 Average Output Current IO 25 mA 1 Supply Voltage VCC 0 20 V Output Voltage VO -0.5 20 V 1 Total Package Power Dissipation PT 210 mW 2 HCPL-223X 294 Output Power Dissipation PO See Figure 7 1 Lead Solder Temperature (Through Hole Parts Only) 260°C for 10 sec., 1.6 mm below seating plane HCNW22XX 260°C for 10 sec., up to seating plane Solder Reflow Temperature Profile See Package Outline Drawings section (Surface Mount Parts Only) Recommended Operating Conditions Parameter Symbol Min. Max. Units Power Supply Voltage VCC 4.5 20 V Forward Input Current (ON) IF(ON) 1.6* 5 mA HCPL-223X 1.8† Forward Input Voltage (OFF) VF(OFF) - 0.8 V Operating Temperature TA -40 85 °C Junction Temperature TJ -40 125 °C Fan Out N 4 TTL Loads *The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband. †The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.

-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified. All Typicals at TA = 25°C. See Note 7. Logic Low Output Voltage VOL 0.5 V IOL = 6.4 mA (4 TTL Loads) 1, 3 1 Logic High Output Voltage VOH 2.4 ** V IOH = -2.6 mA 2, 3, 1 2.7 IOH = -0.4 mA Output Leakage Current IOHH 100 µA VO = 5.5 V IF = 5 mA 1

500 VO = 20 V

Logic Low Supply ICCL 3.7 6.0 mA VCC = 5.5 V VF = 0 V 4.3 7.0 VCC = 20 V HCPL-223X 7.4 12.0 VCC = 5.5 V 8.6 14.0 VCC = 20 V Logic High Supply ICCH 2.4 4.0 mA VCC = 5.5 V IF = 5 mA 2.7 5.0 VCC = 20 V HCPL-223X 4.8 8.0 VCC = 5.5 V 5.4 10.0 VCC = 20 V Logic Low Short Circuit IOSL 15 mA VO = VCC = 5.5 V VF = 0 V 1, 3

20 VO = VCC = 20 V VO = GND

Logic High Short Circuit IOSH -10 mA VCC = 5.5 V IF = 5 mA 1, 3 -20 VCC = 20 V Input Forward Voltage VF 1.5 1.7 V TA = 25°C IF = 5 mA 4 1 1.85 HCNW22XX 1.5 1.82 TA = 25°C 1.95 Input Reverse Breakdown BVR 5 V IR = 10 µA 1 HCNW22XX 3 IR = 100 µA Input Diode Temperature ∆VF -1.7 mV/°C IF = 5 mA HCNW22XX ∆TA -1.4 Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V 1, 4 HCNW22XX 70 *For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA. **Typical VOH = VCC - 2.1 V. (VOUT < VCC) Current Current Output Current Voltage Coefficient Output Current IO = Open IO = Open

Parameter Sym. Device Min. Units Test Conditions Fig. Note Logic High |CMH| HCPL-2201/02 1,000 V/µs |VCM| = 50 V VCC = 5 V 10 1, 7 Common Mode HCPL-0201 IF = 1.6 mA† T A = 25°C Transient HCPL-2231 Immunity HCNW2201 HCPL-2211/12 5,000 V/µs |VCM| = 300 V HCPL-0211 IF = 1.6 mA‡ HCPL-2232 10,000 V/µs |VCM| = 1 kV HCNW2211 IF = 5.0 mA Logic Low |CML| HCPL-2201/02 1,000 V/µs |VCM| = 50 V VF = 0 V 10 1, 7 Common Mode HCPL-0201 VCC = 5 V Transient HCPL-2231 TA = 25°C Immunity HCNW2201 HCPL-2211/12 10,000 V/µs |VCM| = 1 kV HCPL-0211 HCPL-2232 HCNW2211 *For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA. †IF = 1.8 mA for HCPL-2231. ‡IF = 1.8 mA for HCPL-2232. Switching Specifications (AC) -40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON) * ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V. All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise specified. Propagation Delay Time tPHL 150 ns Without Peaking Capacitor 5, 6 1, 6

160 HCNW22XX

150 300 With Peaking Capacitor Propagation Delay Time tPLH 110 ns Without Peaking Capacitor 5, 6 1, 6

180 HCNW22XX

90 300 With Peaking Capacitor Output Rise Time (10-90%) tr 30 ns 5, 9 1 Output Fall Time (90-10%) tf 7 ns 5, 9 1 to Logic Low Output Level to Logic High Output Level

Notes: 1. Each channel. 2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C. 3. Duration of output short circuit time should not exceed 10 ms. 4. For single devices, input capacitance is measured between pin 2 and pin 3. 5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together. 6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing edge of the output pulse. 7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V. CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V. 8. For HCPL-2202/12, VO is on pin 6. 9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended. 10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable. 11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/DIN EN 60747-5-2 Insulation Characteristics Table. 12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together. Package Characteristics Input-Output Momentary VISO 3750 V rms RH < 50%, t = 1 min. 5, 10 HCNW22XX 5000 TA = 25°C 5, 11 Input-Output Resistance RI-O 1012 Ω VI-O = 500 Vdc 5 HCNW22XX 1012 1013 T A = 25°C

1011 TA = 100°C

Input-Output Capacitance CI-O 0.6 pF f = 1 MHz, 5 HCNW22XX 0.5 0.6 TA = 25°C, VI-O = 0 Vdc Input-Input Insulation II-I 0.005 µA Relative Humidity = 45%, 12 Leakage Current t = 5 s, VI-I = 500 V Resistance (Input-Input) RI-I 1011 Ω V I-I = 500 V 12 Capacitance (Input-Input) CI-I 0.25 pF f = 1 MHz 12 *The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203 Withstand Voltage*

For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved. Obsoletes AV01-0556EN AV02-0674EN - January 28, 2010