G88405549 CARLOGAVAZZI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Specifications are subject to change without notice (19.01.2017) 1 Product De scrip tion Ordering Key Type: Dupline® Housing Transceiver No. of channels/in- and outputs Output type Remote Transceiver Type G 8840 5549

  • Small-sized transceiver
  • Output load: 8 A/63 VAC
  • Powered via Dupline
  • Address coding by GAP 1605
  • 3 contact inputs
  • 1 tamper channel The Dupline ® decentralised transceiver has a built-in SPDT relay for control of a load of up to 8 A/63 VAC. The module is especially designed for applications requiring a flexible, decentralised instal- Type Selection Ordering no. G 8840 5549 lation with a separate power and signal (control) bus. The compact size of the module makes it fit in small enclosu- res. Output Spec i fi ca tions Output 1 SPDT relay Contact ratings (Ag/Ni 90/10 ) µ (micro gap) Resistive load 8 A/63 VAC

8 A/24 VDC

0,8 A/63 VDC Mechanical lifetime > 2x106 operations Electrical lifetime > 1x106 operations/

24 VDC 2A

1x105 operations/

24 VDC 8A

Minimum load (recommended) 10 mA/12 V Operating frequency ≤ 60 operations/minute Response time 1 pulse train G 8840 5549 Supplied by Dupline® Normal consumption ≤ 1.6 mA Charge consumption ≤ 3.1 mA (for max 1 s after relay state change) Power-on delay Typ. 2 s Power-off delay ≤ 1 s General Spec i fi ca tions Environment Pollution degree 3 (IEC 60664) Operation temperature 0° to +50°C (32° to 122°F) Storage temperature -50° to +85°C (-58° to 185°F) Humidity (non-condensing) 20 to 80% Housing Material Noryl GFN 1, black Dimensions (h x w x d) 26 x 39 x 17 mm Supply Spec i fi ca tions Input Spec i fi ca tions Inputs 3 contacts + one tamper channel (I/O 5-8) Open loop voltage 2 to 3 VDC Short-circuit current 25 µA Operating time for signal “1” ≤ 1 pulse train + 10 ms Operating time for signal “0” ≤ 1 pulse train + 110 ms Contact resistance ≤ 1 kΩ Cable length ≤ 3 m Dielectric Voltage Inputs - Dupline® None Inputs - Output ≥ 200 VAC (rms) Dupline® - Output ≥ 200 VAC (rms)

2 Specifications are subject to change without notice (19.01.2017) S Violet Green White Black Yellow

1 Orange

input: Wiring Diagram G 8840 5549 Mode of Operation The in- and output address- es and fail polarity can be coded by means of the code programmer GAP 1605, with the GAP-THP-CAB cable. Upon loss of the Dupline carrier, the output goes to the predefined fail polarity. The three contact inputs are located on in/out 5, 6 and 7 on the GAP 1605. Tamper channel: If a chan- nel is programmed on in/out 8, it will be transmitted as long as the module is con- nected to Dupline. Wire Connections Bus: White = Dupline® signal Black = Dupline® GND Output: Brown - Blue = Relay contact-set NC Brown - Orange = Relay contact-set NO Bus wires: 2 x 0.75 mm2,

250 V isolation, single core, 150 mm

Output wires: 3 x 1.5 mm2 , Input wires: 3 x 0.25 mm2 , Multi core, 150 mm 2617 Dimensions Channel Configuration On GAP 1605 the in/out configuration is as follows: In/out 1: Relay output. In/out 5: Contact input 1. Green wire. In/out 6: Contact input 2. Yellow wire. In/out 7: Contact input 3. Violet wire. In/out 8: Tamper channel (built-in)