GSERIES XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 6

Technical content

Features

  • Output Voltages from 100V to 6kV
  • Output Voltage Proportional to Input
  • Low Turn-on Voltage 0.7VDC
  • Input to Output Isolation
  • Dual Output Models
  • No Minimum Load
  • 3 Year Warranty Typical Applications
  • Mass Spectrometry
  • Electrostatic Chucks
  • Electrophoresis
  • Capacitor Charging
  • Particle Counter
  • Ignition/Spark
  • Sustaining Ion Pumps CONVECTION COOLED Dimensions Block Diagram OSCILLATOR RECTIFIER & MULTIPLIER (-) In 5+ Center Tap (for Dual Output option) (-) Output (+) Output Transformer (+) In

Notes: 1. Maximum rated output current is available at maximum rated output voltage and derates linearly as input voltage is decreased. 2. Output voltage is load dependent. Under light or no-load conditions, reduce the input voltage so maximum rated output voltage is not exceeded. 3. Specifications after 30 minute warm-up, full load, at 25°C unless otherwise indicated. 4. Proper thermal management techniques are required to maintain safe case temperature at maximum power output. 5. Ripple specification for center-tapped units applies to the voltage between the positive and negative output terminals. 6. Models G40, G50 & G60 do not have internal bleeder resistors on the output. Provisions must be made externally to discharge the output capacitors. DC-HVDC CONVERTERG Series Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 6000 VDC See Models & Ratings table Output Current 15 mA See Models & Ratings table Output Voltage Tolerance ±3 % At Max Vout, Full Load Minimum Load No minimum load required Regulation Unregulated, Output is proportional to Input. Unloaded output voltage is typically 10% higher than unloaded. Ripple and Noise 0.1 2.0 % See Models & Ratings table Response Time 15 msec 0 to Max Vout, Full Load [G01 to G60] Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage 0.7 12 VDC Input Current, No Load 175 mA See Models and Ratings T able. Input Current, Full Load 400 mA See Models and Ratings T able. Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -10 +60 °C Case temperature Storage Temperature -25 +90 °C Cooling Natural convection Humidity 95 %RH Non-condensing Characteristic Minimum Typical Maximum Units Notes & Conditions Isolation: Input to Output 3500 V <±3500 Bias Switching Frequency 60 190 kHz Stable frequency over entire output voltage range Construction Case material is Diallyl Phthalate (DAP). UL 94 V-0 rated solid vacuum encapsulation Mean Time Between Failure 2.29 Mhrs Bellcore TR 332 General

Specifications subject to change without notice. 3 Safety Approvals Safety Agency Standard Notes & Conditions UL IEC/UL/CSA/EN 62368 CE Meets all applicable directives RoHS RoHS 2 and 3 Directive (2011/65/EU) Where applicable External EMI/RFI Shield 0.300 (7.62) 2.000 (50.80) 0.300 (7.62) ø 0.140 (3.56) thru 2 places 4-40 solderable grounding stud 2 places HIGH VOLTAGE 0.31 (7.9) 0.68 (17.3) 0.40 (10.2) 1.60 (40.6) 0.20 (5.1) 0.80 (20.3) 1.60 (40.6) 2.40 (61.0) An AB suffix is used to indicate an added external EMI/RFI Shield as shown above. These five-sided aluminum enclosures feature a durable, non-conductive black anodized finish. On models with outputs of 3kV or higher, special care must be taken to ensure adequate spacing and insulation between the metal can and the high voltage output. Single sided layout, encapsulation, or conformal coating may be required. Case grounding studs must be connected to ground. Case ground is not connected to (-) Input.

Model Number Output Voltage Output Current(1) input Current Ripple No Load Full Load G01 0 to 100V 15mA <100mA <250mA <1.75% G01CT 0 to +/-50V 15mA <100mA <250mA <1.75% G02 0 to 200V 7 .5mA <100mA <250mA <0.75% G02CTAB 0 to +/-100V 7 .5mA <100mA <250mA <0.75% G03 0 to 300V 5mA <100mA <250mA <0.75% G03CTAB 0 to +/-150V 5mA <100mA <250mA <0.75% G04 0 to 400V 3.75mA <100mA <250mA <0.75% G04CTR 0 to +/-200V 3.75mA <100mA <250mA <0.75% G05 0 to 500V 3mA <100mA <250mA <0.1% G06 0 to 600V 2.5mA <100mA <250mA <0.1% G10 0 to 1000V 1.5mA <100mA <250mA <0.1% G12 0 to 1200V 1.25mA <150mA <275mA <0.1% G12AB 0 to 1200V 1.25mA <150mA <275mA <0.1% G12CTR 0 to +/-600V 1.25mA <150mA <275mA <0.1% G15 0 to 1500V 1mA <125mA <275mA <0.5% G15AB 0 to 1500V 1mA <125mA <275mA <0.5% G20 0 to 2000V 0.75mA <165mA <275mA <0.5% G25 0 to 2500V 0.6mA <125mA <275mA <1% G25AB 0 to 2500V 0.6mA <125mA <275mA <1% G25CT 0 to +/-1250V 0.6mA <125mA <275mA <1% G30 0 to 3000V 0.5mA <125mA <300mA <2% G30AB 0 to 3000V 0.5mA <125mA <300mA <2% G30CT 0 to +/-1500V 0.5mA <125mA <300mA <2% G40 0 to 4000V 0.37mA <125mA <300mA <1% G40RAB 0 to 4000V 0.37mA <125mA <300mA <1% G50 0 to 5000V 0.3mA <125mA <300mA <2% G50AB 0 to 5000V 0.3mA <125mA <300mA <2% G50CT 0 to +/-2500V 0.3mA <125mA <300mA <2% G60 0 to 6000V 0.25mA <125mA <300mA <2% G60RAB 0 to 6000V 0.25mA <125mA <300mA <2% G60CT 0 to +/-3000V 0.25mA <125mA <300mA <2% G60CTAB 0 to +/-3000V 0.25mA <125mA <300mA <2% GPMT 0 to 1250V 0.35mA <35mA <75mA <0.05% Models & Ratings Notes: 1. All orderable part numbers are listed above. 3. AB suffix indicates external shield, see Mechanicals. 4. R suffix is used as a RoHS indicator for legacy models. 5. Model GPMT is rated for 0.4375 Watts.

Specifications subject to change without notice. 5 Mechanical Details Notes: 1. All dimensions are in inches (mm) 2. Weight 1.5oz (43g) 3. Tolerance: X.XX±0.02 (0.51) 4. Pin Tolerance: ±0.005 (0.127) G01 to G40 G01CT to G12CT PCB Layout Pin Function 1 (+) Input 2 (-) Input 3 (+) Output 4 (-) Output

5 Dual Output/Center T ap (Optional)

0.031 (0.79) Ø PC pin *5 places TOP VIEW 1.000 (25.40) 1.200 (30.48) G01CT to G20CT Recommended hole & pad O.D. size: *5 places 0.20 (5.1) 0.800 (20.32) RECOMMENDED PCB LAYOUT TOP VIEW use for G01 to G40 & * Optional dual output (center tap) 0.500 (12.70) 0.25 (6.4) 0.35 (8.9) 0.15 (3.8) 0.63 (16.0) 1.50 (38.1) 1.50 (38.1) G25CT to G60CT use for G50 to G60 & HIGH VOLTAGE 0.031 (0.79) Ø PC pin 5 places TOP VIEW 1.200 (30.48) RECOMMENDED PCB LAYOUT Recommended hole & pad O.D. size: *5 places 0.600 (15.24) 0.20 (5.1) 0.800 (20.32) TOP VIEW 0.63 (16.0) 1.50 (38.1) 1.50 (38.1) 0.15 (3.8) 0.35 (8.9) 0.15 (3.8) 1.200 (30.48) * Optional dual output (center tap)

624 Jan 2022

Positive Output Negative Output Dual Output +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 Typical Output vs. Input Voltage 10 20 30 40 50 60 70 80 90 100 100 120 110 Output Voltage (%) Input Voltage (%) Full Load No Load