G21305521700 CARLOGAVAZZI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Specifications are subject to change without notice (29.04.03) 1 Dupline® is a registered trademark. A product of the CARLO GAVAZZI Group

  • 8 NPN- or PNP-transistor outputs for control of floor-indicators
  • Open printed circuit board
  • Bracket for DIN-rail mounting available
  • LED-indications for supply and Dupline ® carrier
  • 3-wire system with Dupline ® and DC-supply through G 2196 0000 700
  • Channel coding by GAP 1605 Product Description Ordering Key Module with 8 NPN- or PNP- transistor outputs for direct interface to elevator floor indicators. The 8 outputs can either be connected to the 8 inputs of intelligent floor indi- cators which are controlled by bit-combinations or they can be used to drive LED- segments directly. All modules in an elevator is connected to the same 3 wires for bus- communication with the con- trol system and DC-power- supply for the lamps/LED’s. Installer friendly mounting, operation and maintenance without requirement of any special tools or programm- ing. Type: Dupline Open PCB Output-Module Number of I/Os Output type DC-supply Type Selection Supply Ordering no. Ordering no. NPN-outputs PNP-outputs 10-30 VDC G 2130 5511 700 G 2130 5521 700 G 2130 5521 700 Output Specifications Supply Specifications Output-Module for Elevators Outputs 8 PNP-transistors Output voltage drop ≤ 2.0 V Current per output ≤ 100 mA Total load capability (01..08) ≤ 500 mA Reverse polarity protection Yes Short-circuit protection None Built-in protective diodes Yes Off-state leakage current ≤ 200 µA Response time 1 pulse train (136 ms @ 128 channels) Power supply Overvoltage cat. III (IEC 60664) Rated operational voltage (Vin) 10-30 VDC (ripple included) Ripple ≤ 3 V Reverse polarity protection Yes Current consumption ≤ 45 mA Power dissipation ≤ 1 W Inrush current ≤ 1 A Transient protection voltage 800 V Dielectric voltage Supply - Dupline ® None Supply - Outputs None Type G 2130 55.1 700 General Specifications Power ON delay Typ. 2 s Indication for Supply ON LED, green Dupline® carrier LED, yellow Environment Operating temperature -20 to +50°C (-4 to +122°F) Storage temperature -50 to +85°C (-58 to +185°F) Humidity (non-condensing) 20 - 80% Mechanical resistance Shock 15 G (11 ms) Vibration 2 G (6 to 55 Hz) Dimensions Open PCB 74 x 59 mm 4 pcs. of nylon PA6 snap locks are included for mount- ing the PCB in ø 4.8 holes Weight 50 g

2 Specifications are subject to change without notice (28.09.99) Dupline® is a registered trademark. A product of the CARLO GAVAZZI Group Mode of Operation The output unit uses three wires for the communication with all the other I/O-units of an installation, for the sup- ply of the I/O-units and for the loads connected to the outputs of the units. This implies, that the “common” of the communication signal is identical to the “minus” of the supply. The DC supply voltage must connect to the system through a G 2196 0000 700, which also performs the channel generator function and the RS485 communica- tion link to the elevator con- troller (please refer to the data sheet for G2196 0000 700 for details). 8 out of the 128 available Dupline ® adresses should be reserved to control the floor- indicators. Since all the indic- ators must show the same value, the output modules can all be coded to read the same adresses. This implies that only 8 adresses will be occupied for floor indication no matter how many indic- ators are installed. The output status of all out- puts of an output unit may be predefined for cases like loss of power and loss of communication. Please refer to the paragraph “Output status setting” of the data sheet for the GAP 1605 to change the default setting (all outputs OFF). Pin Allocation Terminal DUP GND POW DC + O 1 O 2 O 3 O 4 O 5 O 6 O 7 O 8 Dup (Dupline® S) GND DC + POW (Supply input) Input/Output Dupline® signal Dupline® + supply GND Supply IN DC for output loads Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Wiring Diagrams G 2130 55.1 700 Accessories Aluminium bracket for DIN-mounting 8047- bracket DIN-rail FMD 411 Channel program plug Supply LIne Dup (Dupline® S) GND DC + POW (Supply input) Channel program plug Supply LIne G 21305511... G 21305521...