G200 MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Miniature DIP Package 1.0 kVDC Isolation 2W Output Power Single & Dual Outputs 3.6 MH MTBF Low Cost Electrical Specifi cations Specifi cations typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 43.2 48.0 52.8 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy !1.0 !3.0 % Output Voltage Balance Dual Output , Balanced Loads !0.1 !1.0 % Line Regulation For Vin Change of 1% !1.2 !1.5 % Load Regulation See Model Selection Guide Ripple & Noise (20 MHz) 100 150 mV P - P Ripple & Noise (20 MHz) Over Line, Load & Temp. 200 mV P - P Ripple & Noise (20 MHz) 5 mV rms Output Power Protection 120 % Temperature Coeffi cient !0.01 !0.02 %/1C Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,000 VDC Isolation Resistance 500 VDC 1,000 M Ω Isolation Capacitance 100 kHz, 1V 80 120 pF Switching Frequency 50 80 100 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range -40 +25 +70 1C Storage Temperature Range -40 +125 1C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic Weight 0.09 Oz (2.7g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 251C, Gnd Benign 3.6 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Internal Power Dissipation All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct Compact MiniDIP, 2W Single & Dual Output DC/DC Converters G200 Series MicroPower Direct TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com WEB: www/micropowerdirect.com
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the top of the unit Model Number Input Output Load Regulation (%, Max) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load G235 48 43.2 - 54.8 28 6 !5.0 !200.0 ! 4.0 8 75 100
232 Tosca Drive, Stoughton, MA 02072
www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481 Mechanical Dimensions MicroPower Direct Pin Single Dual 1 -Vin -Vin 7N C N C
8 No Pin Common
NC = No Connection Pin Connections Single Output µF Max Dual Output µF Max 470 !390 Capacitive Load Model Selection Guide Notes: 1. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common. 2. These units do not require external comonents to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (4.7 µF to 10 µF) may be used to reduce ripple. Derating Curve Ambient Temperature 1C 85-40 -20 0 5 15 25 35 45 55 65 75 95 105 100 Output Power % 0.80 (20.32) 11 9 0.10 0.10 (2.54) 0.01 (0.25) 0.01 (0.25) 0.40 (10.2) 0.12 (3.05) 0.05 (1.25) Bottom Side Note: “T” = 0.27 (6.85) For 5, 12 & 24 VDC Input Models 0.30 (7.50) For 48 VDC Input Models “T”