G100R MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
/square6 Miniature DIP Package /square6 1.0 kVDC Isolation /square6 !0.5% Line/Load Regulation /square6 1W Output Power /square6 2.7 MH MTBF /square6 Low Cost Electrical Specifi cations Specifi cations typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Input Filter Internal Capacitor Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy !1.0 !5.0 % Line Regulation For Vin Change of Min to Max !0.5 % Load Regulation For Iout = 20% to 100% !0.5 % Ripple & Noise (20 MHz) 50 mV P - P Output Power Protection 120 % Temperature Coeffi cient !0.01 !0.02 %/1C Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,000 VDC Isolation Resistance 500 VDC 1,000 M Ω Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 80 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range -40 +25 +85 1C Storage Temperature Range -40 +125 1C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic Weight 0.09 Oz (2.7g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 251C, Gnd Benign 2.7 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 6.0 VDC12 VDC Input -0.7 14.0 24 VDC Input -0.7 28.0 Internal Power Dissipation All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct Tightly Regulated, 1W Ultra-Miniature DIP DC/DC Converters G100R Series MicroPower Direct /square6 TEL: (781) 344-8226 /square6 FAX: (781) 344-8481 /square6 E-Mail: sales@micropowerdirect.com /square6 WEB: www/micropowerdirect.com
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit Model Number Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load
232 Tosca Drive, Stoughton, MA 02072
www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481 Mechanical Dimensions MicroPower Direct Pin Single 1- V i n 7N C 9+ V o u t 11 -Vout 14 +Vin NC = No Connection Pin Connections µF Max Capacitive Load Model Selection Guide Derating Curve Ambient Temperature 1C 85-40 -20 0 5 15 25 35 45 55 65 75 95 105 100 Output Power % 0.80 (20.32) 11 9 0.10 0.10 (2.54) 0.01 (0.25) 0.01 (0.25) 0.40 (10.2) 0.12 (3.05) 0.05 (1.25) Bottom Side 0.27 (6.85) Notes: 1. These units do not require external comonents to oper- ate, but the use of an input capacitor (10 µF) may en- hance performance in some applications. An output cap- acitor (4.7 µF to 10 µF) may be used to reduce ripple.