G104V1-T01

G104V1-T01 AZDISPLAYS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 26

Technical content

Doc. N o.: Issued Date : Aug.9.2006 Model No :G10 4V1-T01 Appr oval Version 2.1 TFT LCD Approval Specification MODEL NO.: G104V1-T01 記錄 工作 審核 角色 投票 2006-08-15 11:53:32 CST Approve by Dept. Mgr.(QA RA) tomy_chen(陳永一 /52720/54140/43150) Assignee Accept 2006-08-10 18:17:48 CST Approve by Director teren_lin(林添仁/56910/36064) Director Accept Customer: Approved by: Note: FOR MORE INFORMATION: AZ DISPLAYS, INC.

75 COLUMBIA, ALISO VIEJO, CA 92656

Http://www.AZDISPLAYS.com

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 - CONTENTS -

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

2.2.2 BACKLIGHT UNIT

3.1 TFT LCD MODULE

3.2 BACKLIGHT UNIT

4.1 TFT LCD MODULE

4.2 BACKLIGHT UNIT

5.1 TFT LCD MODULE

5.2 SCANNING DIRECTION

5.3 BACKLIGHT UNIT

5.4 COLOR DATA INPUT ASSIGNMENT

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

8.1 PACKING SPECIFICATIONS

8.2 PACKING METHOD

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

10.2 SAFETY PRECAUTIONS

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1

REVISION HISTORY

Version Date Section Description Ver 2.0 Ver 2.1 Nov.07. 05 Aug.09 . 06 All 2.1 G104V1-T01 Specifications was first issued. ABSOLUTE RATINGS OF ENVIRONMENT 1.Change the Operation Temp.

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 1. GENERAL DESCRIPTION G104V1-T01 is an 10.4 inch TFT Liquid Crystal Display module with a 2-CCFL Backlight unit and a-31-pin-and-1ch-TTL interface. This module supports 640 x 480 VGA mode and can display 262,144 colors. The inverter module for Backlight is not built in.

• Wide viewing angle. - High contrast ratio - Fast response time - High color saturation - VGA (640 x 480 pixels) resolution - Wide operating temperature - DE (Data Enable) mode - CMOS/TTL (Transistor –Transistor Logic) Interface - Reversible - scan function

-TFT LCD Monitor -TFT LCD TV - Factory Application - Amusement - Vehicle

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note Diagonal Size 264.0 (10.4 inch ) mm Active Area 211.2x158.4 mm Bezel Opening Area 215.4x161.8 mm (1) Driver Element a-si TFT active matrix - - Pixel Number 640xR.G.B.x480 pixel - Pixel Pitch 0.33x0.33 mm - Pixel Arrangement RGB vertical stripe - - Display Colors 262,144 color - Display Mode Normally Black - - Surface Treatment Hard Coating (3H), AG (Haze 25%) - - Weight 470 g Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Item Min. Typ. Max. Unit Note Horizontal(H) 225.0 225.5 226.0 mm Vertical(V) 175.8 176.3 176.8 mm Module Size Depth(D) - 9.5 10.0 mm (1) I/F connector mounting position The mounting inclination of the connector makes the screen center within ±0.5mm as the horizontal. (2) Note (1) Please refer to the attached drawings for more information of front and back outline dimensions. Note (2) Connector mounting position +/- 0.5mm

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 2. ABSOLUTE MAXIMUM RATINGS No. Test Item Test Condition Note

1 High Temperature Storage Test 80℃, 240 hours

2 Low Temperature Storage Test -20℃, 240 hours

3 Thermal Shock Storage Test -20℃, 0.5hour←→80℃, 0.5hour; 100cycles, 1hour/cycle

4 High Temperature Operation Test 70℃, 240 hours

5 Low Temperature Operation Test -20℃, 240 hours

6 High Temperature & High Humidity

Operation Test 60℃, RH 90%, 240hours

7 Heat Cycle Operation Test -20℃, 1hour←→70℃, 1hour; 50cycles, 4hour/cycle

(1) (2)

8 ESD Test (Operation)

150pF, 330Ω, 1sec/cycle Condition 1 : panel contact, ±8KV Condition 2 : panel non-contact ±15KV (2) 9 Shock (Non-Operating) 220G, 2ms, half sine wave, 1 time for ± X, ± Y, ± Z. (2)(3) 10 Vibration (Non-Operating) 1.5G, 10 ~ 300 Hz , 10min/cycle, 3 cycles each X, Y , Z (2)(3) Note (1) Temperature and relative humidity range is shown in the figure below. (a) 90 %RH Max. (Ta ≦ 40 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC). (c) No condensation. Note (2) No display malfunctions. Note (3) At testing Vibration and Shock, the fixtur e in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. Note (4) The temperature of panel display surface area should be 80 ºC Max.

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Value Item Symbol Min. Max. Unit Note Power Supply Voltage Vcc -0.3 6.0 V Logic Input Voltage V IN -0.3 V CC + 0.3 V (1) Value Item Symbol Min. Max. Unit Note Lamp Voltage V L - 2.5K V RMS (1), (2), I L = (5.5)mA Lamp Current I L 2.0 6.0 mA RMS Lamp Frequency F L 45 80 KHz (1), (2) Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to 3.2 for further IL information). Relative Humidity (%RH) Operating Range Temperature (ºC) 100 8060 -20 40 0 20-40

10 Storage Range

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 3. ELECTRICAL CHARACTERISTICS 3 . 1 T F T L C D M O D U L E T a = 2 5 ± 2 º C Value Parameter Symbol Min. Typ. Max. Unit Note Power Supply Voltage V CC 3.0 3.3 / 5 5.25 V - Ripple Voltage V RP - - 100 mV - Rush Current I RUSH - - 1 A (2) White - 420 - mA (3)a Black - 380 - mA (3)b Power Supply Current Vertical Stripe - - 470 - mA (3)c VIH 0.7VCC - V CC V Logic input voltage VIL 0 - 0.3V CC V Note (1) The module should be always operated within above ranges. Note (2) Measurement Conditions: VCC = 3.3 V, Ta = 25 ± 2 ºC. Vcc rising time is 470µs 470µs Vcc GND 0.9Vcc 0.1Vcc (High to Low) (Control Signal) +12V SW 1uF Vcc Vcc 2SK1470 Q1 2SK1475 47K VR1 47K C2 0.01uF 1uF FUSE (LCD Module Input)

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, f v = 60 Hz, whereas a power dissipation check pattern below is displayed. Active Area a. White Pattern Active Area c. Vertical Stripe Pattern R R R R R R R R G G G G B B B B B B G G G G B B B B R R Active Area b. Black Pattern

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Ta = 25 ± 2 ºC Value Parameter Symbol Min. Typ. Max. Unit Note Lamp Input Voltage V L 440 490 540 V RMS (1), I L = (5.5) mA Lamp Current I L 2.0 5.5 6.0 mA RMS (1) - - 770 (25 oC) V RMS (2) Lamp Turn On Voltage V S - - 960 (0 oC) V RMS (2) Operating Frequency F L 45 - 80 KHz (3) Lamp Life Time L BL 50,000 - - Hrs (5) Power Consumption P L - 5.39 - W (4), I L = 5.5 mA Note (1) IL means the lamp current of one lamp. Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise the lamp may not be turned on. Note (3) The lamp frequency may produce interferen ce with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (4) P L = IL ×VL ×2 Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition Ta = 25 ±2 oC and IL = ( 5.5 ) mArms until one of the following events occurs: (a) When the brightness becomes or lower than 50% of its original value. (b) When the effective ignition length becomes or lower than 80% of its original value. (Effective ignition length is defined as an area that ha s less than 70% brightness compared to the brightness in the center point.) Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. The performance of the Backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for the lamp. All the parameters of an inverter s hould be carefully designed to avoid producing too much current leakage from high voltage output of the inverter. When designing or ordering the inverter please make sure that a poor lighting ca used by the mismatch of the Backlight and the inverter (miss-lighting, flicker, etc.) never occu rs. If the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. The output of the inverter must have symmetrical (negative and positive) voltage waveform and symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. Requirements for a system inverter design, which is intended to have a better display performance, a

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its leakage current. a. The asymmetry rate of the inverter waveform should be 10% below; b. The distortion rate of the waveform should be within √2 ± 10%; c. The ideal sine wave form shall be symmetric in positive and negative polarities. I p I -p * Asymmetry rate: | I p – I –p | / Irms * 100% * Distortion rate I p (or I –p) / Irms

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 4. BLOCK DIAGRAM (640x3x480) DATA DRIVER IC SCAN DRIVER IC BACKLIGHT UNIT TTL INPUT / TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE INPUT CONNECTOR ( DF9C-31P-1V ) VL LAMP CONNECTOR ( BHR-03VS-1 ) DCLK HS VS R0~R5 G0~G5 B0~B5 DE DPSR V CC GND

3 HV (Pink)

1 LV (White)

2 HV (Pink)

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 5. INPUT TERMINAL PIN ASSIGNMENT

1 GND Ground

2 DCLK Dot clock

3 HS Horizontal synchronous

4 VS Vertical synchronous

5 GND Ground

6 R0 Red data (LSB)

7 R1 Red data

8 R2 Red data

9 R3 Red data

10 R4 Red data

11 R5 Red data (MSB)

12 GND Ground

13 G0 Green data (LSB)

14 G1 Green data

15 G2 Green data

16 G3 Green data

17 G4 Green data

18 G5 Green data (MSB)

19 GND Ground

20 B0 Blue data (LSB)

21 B1 Blue data

22 B2 Blue data

23 B3 Blue data

24 B4 Blue data

25 B5 Blue data (MSB)

26 GND Ground

27 DE Data enable signal

28 Vcc Power supply

29 Vcc Power supply

30 N.C. Reserved, pleas e keep it floating.

31 DPSR Selection of scan direction

Note (1) Connector Part No.: DF 9C-31P-1V or equivalent.

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 The following figures are seen from a front view and the arrow shows the direction of scan. Figure1.Normal scan (DPSR : Low or Open ) Figure 2. Reverse scan (DPSR : High ) Pin Symbol Description Remark

1 LV Ground White

2 HV1 High Voltage Pink

3 HV2 High Voltage Pink

Note (1) Connector Part No.: BHR-03VS-1 ( J.S.T Mfg,Co,Ltd )

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 The brightness of each primary color (red, green an d blue) is based on the 6-bit gray scale data input for the color. The higher the binary input, the brighter t he color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red(0) / Dark Red(1) Red(2) Red(61) Red(62) Red(63) Gray Scale Of Green Green(0) / Dark Green(1) Green(2) Green(61) Green(62) Green(63) Gray Scale Of Blue Blue(0) / Dark Blue(1) Blue(2) Blue(61) Blue(62) Blue(63) Note (1) 0: Low Level Voltage, 1: High Level Voltage

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 6. INTERFACE TIMING The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency Fc 21 25.175 29 MHz - Dot Clock Duty 0.4 0.5 0.6 Setup Time Tlvs 8 - - ns - Dot Data Hold Time Tlvh 12 - - ns - Frame Rate Fr - 60 - Hz Tv=Tvd+Tvb Total Tv - 800 - Th - Display Tvd 640 640 640 Th - Vertical Active Display Term Blank Tvb - 160 Tv-Tvd Th - Total Th - 525 - Tc Th=Thd+Thb Display Thd 480 480 480 Tc - Horizontal Active Display Term Blank Thb - 45 Th-Thd Tc - INPUT SIGNAL TIMING DIAGRAM TH TC DCLK THD TVD Tv DE DE DATA

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below. Timing Specifications: 0.5 < t1 ≦ 10 ms 0 < t2 ≦ 50 ms 0 < t3 ≦ 50 ms t4 ≧ 500 ms t5 ≧ 200 ms t6 ≧ 200 ms Note (1) Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to 0 V. Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight inverter power must be turned off before the power supply for the logic and the interface signal is invalid. - Power Supply for LCD, Vcc - Interface Signal VI - Power for Lamp Restart Power On Power Off 50%50% 10% t6 t5 t3 t2 90% 10% 90% Valid Data ONOFF OFF

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 7. OPTICAL CHARACTERISTICS Ambient Temperature Ta 25±2 oC Ambient Humidity Ha 50±10 %RH Supply Voltage V CC 3.3 V Input Signal According to typical val ue in "3. ELECTRICAL CHARACTERISTICS" Lamp Current I L 5.5 mA RMS Inverter Operating Frequency F L 61 KHz Inverter (Sumida IV40090T/B2) Note (1) IL means the lamp current of one lamp. The relative measurement methods of optical characteri stics are shown in 7.2. The following items should be measured under the test conditions described in 7.1 and stable environment shown in Note (6). Item Symbol Condition Min. Typ. Max. Unit Note Rx 0.626 Red Ry 0.348 Gx 0.303 Green Gy 0.563 Bx 0.145 Blue By 0.105 Wx 0.319 Color Chromaticity White Wy Typ – 0.03 0.338 Typ + 0.03 - (1), (6) Center Luminance of White L C 400 450 - cd/m 2 (4), (6) Contrast Ratio CR 1000 1500 - - (2), (6) TR - 14 19 Ms Response Time TF - 9 14 Ms (3) White Variation δW θx=0°, θY =0° - 1.25 1.40 - (5) θx+ 80 88 - Horizontal θx- 80 88 - θY+ 80 88 - Viewing Angle Vertical θY- CR ≧ 10 80 88 - Deg. (1),

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Note (1) Definition of Viewing Angle ( θx, θy): Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (5). Note (3) Definition of Response Time (T R, TF) and measurement method:. 12 o’clock direction θy+ = 90º 6 o’clock θy- = 90º θx− θx+ θy- θy+ y- x+ N o r m a l θx = θy = 0º θX+ = 90º θX- = 90º 100% 90% 10% Gray Level 63 Gray Level 0 Gray Level 63 Time TR Optical Response TF 66.67ms66.67ms

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Note (4) Definition of Luminance of White (LC): Measure the luminance of gray level 63 at center point LC = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (5). Note (5) Definition of White Variation (δW): Measure the luminance of gray level 63 at 5 points δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)] Note (6) Measurement Setup: The LCD module should be stabilized at giv en temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room. D W Active Area Vertical Line Horizontal Line : Test Point X=1 to 5 3 4 D/4 D/2 3D/4 W/4 W/2 3W/4 X Photometer CA210, CS-1000T Field of View = 2º 500 mm LCD Module LCD Panel Center of the Screen Light Shield Room (Ambient Luminance < 2 lux)

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 8. PACKAGING (1) 30 LCD modules / 1 Box (2) Box dimensions: 500(L) X 400(W) X 330(H) mm (3) Weight: approximately 15.5Kg (30 modules per box) (1) Carton Packing should have no failure in the following reliability test items. Test Item Test Conditions Note Vibration ISTA STANDARD Random, Frequency Range: 1 – 200 Hz Top & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X) Back & Forth 10 minutes (Y) Non Operation Dropping Test 1 Angle, 3 Edge, 6 Face, 60cm Non Operation Figure. 8-1 Packing method

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 Figure. 8-2 Packing method

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 9. DEFINITION OF LABELS

9.1 CMO MODULE LABEL

The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. (a) Model Name: G104v1 -T01 (b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc. (c) Serial ID: X X X X X X X Y M D L N N N N Serial ID includes the information as below: (a) Manufactured Date: Year: 1~9, for 2000~2009 Month: 1~9, A~C, for Jan. ~ Dec. D a y : 1 ~ 9 , A ~ Y , f o r 1 st to 31st, exclude I ,O, and U. (b) Revision Code: Cover all the change (c) Serial No.: Manufacturing sequence of product (d) Product Line: 1 -> Line1, 2 -> Line 2, …etc. Product Line Year, Month, Date CMO Internal Use CMO Internal Use Revision CMO Internal Use Serial No. CHI MEI OPTOELECTRONICS MADE IN TAIWAN E207943 MADE IN TAIW AN G104V1 -T01 Rev. XX X X X X X X X Y M D L N N N N

D o c . N o . : Issued Date : Aug.9.2006 Model No :G104V1-T01 Approval Version 2.1 10. PRECAUTIONS (1) Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or c ontacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the per formance of module. Please store LCD module within the specified storage conditions. (10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the response time will become slow ly, and the starting voltage of CCFL will be higher than room temperature. (1) The startup voltage of Backlight is approximat ely 1000 Volts. It may cause electrical shock while assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module’s end of life, it is not harmful in case of normal operation and storage.