DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

 Finisar Corporation - August 2015 Rev. D Page 1 Product Specification RoHS-6 Compliant 10Gb/s 10km Single Mode Datacom SFP+ Transceiver FTLX1471D3BCL PRODUCT FEATURES

  • Hot-pluggable SFP+ footprint
  • Supports 9.95 to 10.5Gb/s bit rates*
  • Power dissipation < 1W
  • RoHS-6 compliant (lead-free)
  • Commercial temperature range -5°C to 70°C
  • Single 3.3V power supply
  • Maximum link length of 10km
  • Uncooled 1310nm DFB laser
  • Receiver limiting electrical interface
  • Duplex LC connector
  • Built-in digital diagnostic functions

APPLICATIONS

  • 10GBASE-LR/LW 10G Ethernet
  • 1200-SM-LL-L 10G Fibre Channel Finisar’s FTLX1471D3BCL 10Gb/s Enhanced Small Form Factor Pluggable SFP+ transceivers are designed for use in 10-Gigabit Ethernet links up to 10km over Single Mode fiber. They are compliant with SFF-8431 1, SFF-84322 and IEEE 802.3ae 10GBASE-LR/LW3, and 10G Fibre Channel 1200-SM-LL-L4 Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-84725. The FTLX1471D3BCL is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module. The optical transceivers are compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details. PRODUCT SELECTION FTLX1471D3BCL *Contact Finisar for higher data-rate support.

Pin Symbol Name/Description Ref.

1 VEET Transmitter Ground 1

2 TFAULT Transmitter Fault 2

4 SDA 2-wire Serial Interface Data Line 2

5 SCL 2-wire Serial Interface Clock Line 2

10 VEER Receiver Ground 1

11 VEER Receiver Ground 1

12 RD- Receiver Inverted DATA out. AC Coupled. 13 RD+ Receiver Non-inverted DATA out. AC Coupled.

14 VEER Receiver Ground 1

15 VCCR Receiver Power Supply

16 VCCT Transmitter Power Supply

17 VEET Transmitter Ground 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled.

20 VEET Transmitter Ground 1

  1. Circuit ground is internally isolated from chassis ground.
  2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
  3. Internally pulled down per SFF-8431 Rev 2.0.
  4. LOS is open collector output. Should be pulled up with 4.7k – 10kΩ on host board to a voltage

between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Figure 1. Diagram of Host Board Connector Block Pin Numbers and Names.

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 3 II. Absolute Maximum Ratings Exceeding the limits below may damage the transceiver module permanently. Parameter Symbol Min Typ Max Unit Ref. Maximum Supply Voltage Vcc -0.5 4.0 V Storage Temperature TS -40 85 °C Relative Humidity RH 0 85 % 1 1. Non-condensing. III. Electrical Characteristics (TOP = -5 to 70 °C, VCC = 3.14 to 3.46 Volts) Parameter Symbol Min Typ Max Unit Ref. Supply Voltage Vcc 3.14 3.30 3.46 V Supply Current Icc 200 285 mA Transmitter Input differential impedance Rin 100 Ω 1 Differential data input swing Vin,pp 180 700 mV Transmit Disable Voltage VD 2 Vcc V Transmit Enable Voltage VEN Vee Vee+ 0.8 V Receiver Differential data output swing Vout,pp 300 850 mV 2,6 Output rise time and fall time Tr, Tf 28 ps 3 LOS Fault VLOS fault 2 VccHOST V 4 LOS Normal VLOS norm Vee Vee+0.8 V 4 Power Supply Noise Tolerance VccT/VccR Per SFF-8431 Rev 3.0 mVpp 5 Notes: 1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 2. Into 100Ω differential termination. 3. 20 – 80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s sequence in the PRBS 9 is an acceptable alternative. SFF-8431 Rev 3.0. 4. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of signal is logic 1. 6. The FTLX1471D3BCL is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module. IV. Optical Characteristics (TOP = -5 to 70 °C, VCC3 = 3.14 to 3.46 Volts) Parameter Symbol Min Typ Max Unit Ref. Transmitter Optical Modulation Amplitude (OMA) POMA -5.2 dBm Average Launch Power PAVE -8.2 +0.5 dBm 1 Optical Wavelength λ 1260 1355 nm Side-Mode Suppression Ratio SMSR 30 dB Optical Extinction Ratio ER 3.5 dB Transmitter and Dispersion Penalty TDP 3.2 dB Average Launch power of OFF transmitter POFF -30 dBm Tx Jitter Txj Per 802.3ae requirements

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 4 Relative Intensity Noise RIN -128 dB/Hz Receiver Receiver Sensitivity (OMA) @ 10.3Gb/s RSENS1 -12.6 dBm 2 Stressed Receiver Sensitivity (OMA) @ 10.3Gb/s RSENS2 -10.3 dBm 3 Average Receive Power PAVE -14.2 +0.5 dBm Optical Center Wavelength λC 1260 1600 nm Receiver Reflectance Rrx -12 dB LOS De-Assert LOSD -17 dBm LOS Assert LOSA -30 dBm LOS Hysteresis 0.5 dB Notes: 1. Average power figures are informative only, per IEEE 802.3ae. 2. Valid between 1260 and 1355 nm. Measured with worst ER; BER<10-12; 231 – 1 PRBS. 3. Valid between 1260 and 1355 nm. Per IEEE 802.3ae. V. General Specifications Parameter Symbol Min Typ Max Units Ref. Bit Rate BR 9.95 10.5 Gb/s 1 Bit Error Ratio BER 10-12 2 Max. Supported Link Length LMAX 10 km 1 Notes: 1. 10GBASE-LR, 10GBASE-LW, 1200-SM-LL-L 10GFC. 2. Tested with a 231 – 1 PRBS. VI. Environmental Specifications Finisar FTLX1471D3BCL transceivers have an operating temperature range from -5°C to +70°C case temperature. Parameter Symbol Min Typ Max Units Ref. Case Operating Temperature Top -5 70 °C Storage Temperature Tsto -40 85 °C VII. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 5 VIII. Digital Diagnostic Functions Finisar FTLX1471D3BCL SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP+ transceivers provide a enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E 2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN- 2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E 2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation 1,5 and Finisar Application Note AN-2030. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 6 IX. Digital Diagnostic Specifications FTLX1471D3BCL transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Symbol Min Typ Max Units Ref. Accuracy Internally measured transceiver temperature ∆DDTemperature 3 ºC Internally measured transceiver supply voltage ∆DDVoltage 3 % Measured TX bias current ∆DDBias 10 % 1 Measured TX output power ∆DDTx-Power 2 dB Measured RX received average optical power ∆DDRx-Power 2 dB Dynamic Range for Rated Accuracy Internally measured transceiver temperature DDTemperature -5 70 ºC Internally measured transceiver supply voltage DDVoltage 3.1 3.5 V Measured TX bias current DDBias 10 90 mA Measured TX output power DDTx-Power -8.2 +0.5 dBm Measured RX received average optical power DDRx-Power -14.2 +0.5 dBm Max Reporting Range Internally measured transceiver temperature DDTemperature -40 125 ºC Internally measured transceiver supply voltage DDVoltage 2.8 4.0 V Measured TX bias current DDBias 0 20 mA Measured TX output power DDTx-Power -10 +2 dBm Measured RX received average optical power DDRx-Power -22 +2 dBm Notes: 1. Accuracy of measured Tx bias current is 10% of the actual bias current from the laser driver to the laser.

Figure 2. FTLX1471D3BCL Mechanical Dimensions.

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 8 XI. PCB Layout and Bezel Recommendations

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 9

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 10 XII. Host - Transceiver Interface Block Diagram Figure 6-Host-Module Interface

FTLX1471D3BCL Datacom SFP+ Product Specification  Finisar Corporation - August 2015 Rev.D Page 11 XIII. References 1. “Specifications for Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module ‘SFP+ ‘”, SFF Document Number SFF-8431, Revision 3.0. 2. “Improved Pluggable Form factor”, SFF Document Number SFF-8432, Revision 4.2, April 18, 2007. 3. IEEE Std 802.3ae, Clause 52, PMD Type 10GBASE-LR. IEEE Standards Department. 4. American National Standard for Information Technology - Fibre Channel - 10 Gigabit Fibre Channel, Rev 3.5, April 9, 2003. 5. “Digital Diagnostics Monitoring Interface for Optical Transceivers”. SFF Document Number SFF-8472, Revision 10.1, March 1, 2007. 6. Directive 2011/65/EU of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. Certain products may use one or more exemptions as allowed by the Directive. 7. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers” XIV. For More Information Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com