FEP6AT GE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage -50 to 200 Volts Forward Current - 6.0 Amperes

FEATURES

♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive center-tap ♦ Glass passivated chip junctions ♦ Superfast recovery times for high efficiency ♦ Low power loss ♦ Low forward voltage, high current capability ♦ For use in low voltage, high frequency inverters, free wheeling and polarity protection applications ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds MECHANICAL DATA Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals:Plated lead solderable per MIL-STD-750, Method 2026 Polarity:As marked Mounting Position:Any Mounting Torque:5 in. - lb. max. Weight:0.08 ounce, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS FEP6AT FEP6BT FEP6CT FEP6DT UNITS Maximum repetitive peak reverse voltage V RRM 50 100 150 200 Volts Maximum RMS voltage V RMS 35 70 105 140 Volts Maximum DC blocking voltage V DC 50 100 150 200 Volts Maximum average forward rectified current at TC =100° I (AV) 6.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) I FSM 100.0 Amps Maximum instantaneous forward voltage per leg at 3.0A VF 0.975 Volts Maximum DC reverse current T C =25°C 5.0 at rated DC blocking voltage T C =100°C IR 50.0 µA Maximum reverse recovery time per leg (NOTE 1) trr 35.0 ns Typical thermal resistance(NOTE 2) R Θ JA 20.0 °C/W (NOTE 3) R Θ JC 3.6 Typical junction capacitance per leg (NOTE 4) C J 28.0 pF Operating junction and storage temperature range T J, TSTG -55 to +150 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, Ir=1.0A, Irr=0.25A (2) Thermal resistance from junction to ambient in free air, no heatsink (3) Thermal resistance from junction to case per leg mounted on heatsink (4) Measured at 1.0 MH Z and applied reverse voltage of 4.0 Volts 0.415 (10.54) MAX. 0.154 (3.91) 0.148 (3.74)DIA. 0.113 (2.87) 0.103 (2.62) 0.185 (4.70) 0.175 (4.44) 0.055 (1.39) 0.045 (1.14) 0.145 (3.68) 0.135 (3.43) 0.350 (8.89) 0.330 (8.38) 0.160 (4.06) 0.140 (3.56) 0.037 (0.94) 0.027 (0.68) 0.205 (5.20) 0.195 (4.95) 0.560 (14.22) 0.530 (13.46) 0.022 (0.56) 0.014 (0.35) 0.110 (2.79) 0.100 (2.54) PIN 1 2 3 PIN 1 PIN 3 CASE 1.148 (29.16) 1.118 (28.40) 0.105 (2.67) 0.095 (2.41) 0.410 (10.41) 0.390 (9.91) 0.105 (2.67) 0.095 (2.41) 0.635 (16.13) 0.625 (15.87) 0.560 (14.22) 0.530 (13.46) PIN 2 0.370 (9.40) 0.360 (9.14) Dimensions are in inches and (millimeters) TO-220AB

2.0 4.0 6.0 8.0 1 10 100 100 125 150 0.1 1 10 0.1 100 02 0 4 0 6 0 8 0 1 0 0 0.01 0.1 100 RATINGS AND CHARACTERISTIC CURVES FEP6AT THRU FEP6DT FIG. 1 - FORWARD CURRENT DERATING CURVE CASE TEMPERATURE, °C AVERAGE FORWARD CURRENT, AMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG TJ=25°C PULSE WIDTH=300 µs 1% DUTY CYCLE FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD VOLTAGE, VOLTS INSTANTANEOUS FORWARD CURRENT, AMPERES TC =100°C 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES REVERSE VOLTAGE, VOLTS TJ=25°C f=1.0 MHZ Vsig=50mVp-p TJ=125°C NUMBER OF CYCLES AT 60 H Z TJ=125°C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF TJ=25°C TJ=100°C RESISTIVE OR INDUCTIVE LOAD